SolaX Power X1-EVC Series User manual

X1/X3-EVC Series 7.2 kW-22 kW
(Home Edition)
Packing List
Installation Steps
EV-Charger *1
Expansion bolt *3/5
(3 for Socket Type,
5 for Plug Type)
Manual *1
European terminal *3/5
(3 for single-phase;
5 for three-phase)
CT (single-phase)
*1
RJ45 terminal adapter
*1
Cable hook *1
(only for Plug Type)
Quick Installation Guide
*1
CT(three-phase)
*1
STEP 1: Remove the screw from the EV-Charger with the cross screwdriver. Then remove the back bracket away carefully.
STEP 2: Fix the back bracket and the cable hook (only for Plug Type) to the wall.
- Mark the position of the holes. - Insert the expansion bolts.
- Drill holes with φ 8 drill.
- Depth: at least 45 mm.
- Align the bracket and the cable hook (only for Plug Type)
with the holes, and screw the self tapping screws with the
cross screwdriver.
STEP 3: Hang the EV-Charger on the wall for trial, then estimate the required length of input cable (three-core for single-phase, five-core for
three-phase, outer diameter: 12.5-18 mm) and communication cable. After that, take the EV-Charger down.
STEP 4: Unscrew the EV-Charger’s rear cover with the cross screwdriver and take it down. the fastening heads and take the Then undo
waterproof materials away as shown below.
STEP 5: Unscrew the countersunk screw of the base plate of communication board with the cross screwdriver. Then pull the base plate of
communication board out .
Self tapping screw *3/5
(3 for Socket Type,
5 for Plug Type)
Gasket *3/5
(3 for Socket Type,
5 for Plug Type)
RFID Card *2
≥400 mm
(torque:1.5~2 N·m)
②
①
X1/X3-EVC Series 7.2 kW-22 kW
(Home Edition)
X1/X3-EVC Series User Manual
7.2 kW - 22 kW (Home Edition)
Copyright Declaration
The copyright of this manual belongs to SolaX Power Network Technology (Zhejiang) Co., Ltd.
Any corporation or individual should not plagiarize, partially or fully copy it (including
software, etc.), and no reproduction or distribution of it in any form or by any means shall be
allowed. All rights reser ved. SolaX Power Network Technology (Zhejiang) Co., Ltd. reser ves the
right of final interpretation.

CT & WiFi Connection
614.00742.04
Installation Steps
STEP 6: Insert the prepared communication cable through the waterproof connector in sequence as shown below (If the cable is self-made, also
insert the wires into the RJ45 terminals and then use crimping pliers to press them tightly).
STEP 7: Strip the outer sheath of the input cable for a length of 60-70 mm, ensuring all the wires can reach the terminal blocks with a little
excessive length. Use the stripping pliers to strip approx. 12 mm of insulation from the end of all the coloured wires as below. Then crimp the
European terminal with the wire crimper.
STEP 8: Insert the input cable through the waterproof connector in sequence as shown below.
①
③
②
strip length
L1 L2 L3
60-70 mm
60-70 mm
Ou t er Shea t h
12 mm
STEP 9: Insert the wires into the appropriate holes of the terminal
blocks, traight screwdriver then block the terminals with the s .
STEP 10: Press the spring upward and push the base plate of
communication board in. Then screw the countersunk screw.
Diagram:
-Steady the CT on the public grid.
-Insert the other end of the communication cable and the terminal
of CT on each side of the RJ45 terminal adapter.
STEP 11: Push the rear cover to appropriate position of the cables and screw the self tapping screws with the cross screwdriver. Then tighten the
waterproof fastening head.
STEP 12: Hang the EV-Charger up carefully and steady the EV-Charger with the self tapping screw and the cross screwdriver.
For Plug Type, connect the charging connector with the
EV-Charger and hang the connecting cable on the hook.
► CT Connection ► WiFi Connection
Step 1: Use your smart phone to scan below QR code or search
for the keyword “SolaXCloud” in browser to download the
Monitoring App.
Step 2: Create a new account on the Monitoring App.
Step 3: Login and turn to Account page in the app. Then click “Wi-Fi
Connection” and follow the instructions to complete the process.
IOS Google
• Do not place the CT on the N Wire or the PE wire.
• Do not place the CT on the N and L wire
simultaneously.
• Do not place the CT on the non-insulated wires.
• When using the three-phase CT, please clip the CT
clamps on the corresponding phases.
NOTE!
1 2 3456 7 8
1) White with orange stripes
2) Orange
3) White with green stripes
4) Blue
5) White with blue stripes
6) Green
7) White with brown stripes
8) Brown
①
③
②
PIN
Definition
1 2 3 4 5 6 7 8
A1
L1_CT+ B1 L1_CT- L3_CT+ L3_CT-L2_CT+ L2_CT-
* PIN 3, 6, 7, 8 is null for single-phase.
<4 mm
(torque:1.5~1.8 N·m)
L1
L2
L3
N
PE
grid EV- Charger
(torque: 2~2.5 N·m)
L line
CT
Public grid
electricity
Notice: The arrow on the CT
must point at the public grid.
Electrical
grid
other home Load
PV array
AC distribution box
Inverter
CT
Electricity meter,
bidirectional
XXX
Ver s i on:Vx x x x.xx.x x
(torque:0.8~1.5 N·m)
(torque: 2~2.5 N·m)