Soleo AMADEO User manual

DIRECT VENT GAS FIREPLACES
AMADEO MODEL
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
- WHAT TO DO IFYOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not
use any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
- Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
This appliance may be installed in an
aftermarket, permanently located
This appliance may be installed in an
aftermarket, permanently located
This appliance may be installed in an
aftermarket, permanently located
manufactured home (USA only) or in a mobile
home, where not prohibited by local codes.
This appliance is for use only with the type of
gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified conversion kit is used.
Installation and Operation Manual
This appliance has been certified by OMNI-Test
Laboratories, Inc. to ANSI Z21.88-2009 • CSA
2.33-2009 Vented Gas Fireplace Heaters,
CAN/CGA-2.17-M91(R2009),Gas-Fired
Appliances for Use At High Altitudes and CSA
P. P.4.1-02.
Report # 496-S-04-5

2
DO NOT DISCARD
It contains very important installation, operating and maintenance instructions included.
Must read, understand and follow correctly these instructions and details for safety installation and operating. It has to be
consulted by qualified personnel for installation, operation and maintenance.
WARNING
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.
VERY HOT! DO NOT TOUCH!
SEVERE BURNS MAY RESULT!
CLOTHING IGNITION MAY RESULT!
Glass and other surfaces are hot during operation and cool down.
Keep children away.
Carefully supervise children in the same room as appliance. Toddlers are especially susceptible to accidental contact burns. A physical
barrier such as a purpose designed child gate or safety screen will provide increased safety and is highly recommended for use around
appliances where young children are likely to be present.
Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a
professional service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, et cetera. It is
imperative that control compartments, burners and circulating air passageways of the appliance be kept clean
Alert children and adults to hazards of high temperatures.
Do not operate with door or protective parts removed.
Clothing or other flammable material should not be placed on or near the appliance
Installation must be performed by a qualified personnel, factory trained professionals, technician supervised or agency service or official
gas supplier.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.
Do not use this appliance if any part has been under water. Immediately call a qualified technician to inspect the appliance and to replace
any part of the control system and any gas control which has been under water.
The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the National Gas and Propane Installation code, CSA B149.1.
A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations,
ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreation Vehicles and Mobile Housing, CSAZ240.4
Check building codes prior to installation.
Installation must comply with local, regional, state and national codes and regulations.
Consult local building, fire officials or authorities having jurisdictions about restrictions, installation inspection and permits.
Keep appliance dry (mold or rust may cause odors and water may damage controls)
Inspect appliance and components for damage, damaged parts may disturb safe operation.
Do not install damaged, incomplete and substitute components.
SOCA INDUSTRIES INC disclaims all responsibility and warranty if: Installation and use of any damaged appliance or vent system
component. Modification of this appliance or vent system by installation other than as instructed by SOCA INDUSTRIES INC. Improper
positioning of the gas media or the glass door. Installation and use of any component not approved by SOCA INDUSTRIES INC.

3
WARNING
RISK OF FIRE
Provide adequate clearance around air openings, combustibles and service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. Install appliance on hard
metal or wood surfaces extending full width and depth of appliance.
Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may
be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access
to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and
away from hot surfaces
Do not install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.
Construct chase to all clearance specifications in manual.
Locate and install appliance to all clearance specification in manual.
Maintain vent clearance to combustibles as specified.
Do not pack air space with insulation or other materials.
Do not connect this gas appliance to a chimney flue serving a separate solid-fuel or gas burning appliance.
Vent this appliance directly outside.
Use separate vent system for this appliance only.
Always maintain specified clearances around venting and fire stop systems.
Install wall shield and ceiling fire stops as specified.
Do not notch into the framing around the appliance spacers.
Follow these instructions exactly.
Facing materials must be installed properly to prevent fire.
No materials may be substituted without authorization.
Overlap pipe slip section at least 1-1/2”.
Use pilot holes for screws.
Screws must not exceed 1” long.
Pipe may separate if not properly joined.
Do not allow vent to sag below connection point to appliance.
Telescoping flue section of termination cap must be used when connecting pipe section to termination cap.
Maintain a 1-1/2” min. overlap on telescoping flue section of termination cap.
Ensure no debris blocks cap.
Restricted air flow affects burner operation.
Support control when attaching pipe to prevent bending gas line.
Disconnect gas supply piping before pressure testing.
Close the manual shutoff valve before pressure testing.
High pressure may cause over fire condition.
Low pressure may cause explosion.
Verify minimum pressure when other household gas appliances are operating.
Gas buildup during line purge may ignite.
Purge should be performed by qualified technician.
Ensure adequate ventilation.
Ensure there are no ignition sources such as spark or open flames.

4
Check all fittings and connections.
Do not use open flame.
After the gas line installation is completed, all connections must be tightened and check for leaks with non-corrosive leak check solution
and rinse it all after checking.
Do not change the valve settings.
Changing valve settings may result in fire hazard or bodily injury.
Do not wire 110V to valve.
Do not wire 110V to wall switch.
Non combustible clearance must be maintained.
Wood or other combustibles must not be used as sheathing or facing in the non combustible zone.
Facing and/or finishing material must never overhang into the glass opening.
Finishing material must not interfere with operation of louvers or doors or access service.
Finishing must never pass the ½” of metal edge around opening and overhang into glass opening.
Glass door must be in place when appliance is operating.
The glazing frame/assembly shall only be replaced as a complete unit supplied by the manufacturer.
The door glass cannot be replaced except by the manufacturer.

5
TABLE OF CONTENTS
1. GENERAL SAFETY INFORMATION ...............................................................................................................................................7
1.1 CARBON MONOXIDE POISONING..................................................................................................................................................... 7
1.2 INSTRUCTIONS .................................................................................................................................................................................7
2. SPECIFICATIONS ...........................................................................................................................................................................10
2.1 CONSUMPTION, GAS PRESSURE AND EFFICIENCY.......................................................................................................................... 10
2.2 DIMENSIONS OF THE FIREPLACE ....................................................................................................................................................11
3. PREPARING FOR INSTALLATION ...............................................................................................................................................12
3.1 INSTALLATION DESIGN AND PREPARATION ....................................................................................................................................12
3.2 FRAMING THE FIREPLACE...............................................................................................................................................................12
3.3 CLEARANCES TO COMBUSTIBLES.................................................................................................................................................... 17
3.4 TOP CLEARANCES ........................................................................................................................................................................... 18
3.5 FINISHING MATERIAL ..................................................................................................................................................................... 19
4. INSTALLATION OF THE VENT SYSTEM .......................................................................................................................................19
4.1 INSTALLATION PRECAUTIONS.........................................................................................................................................................19
4.2 LOCATION OUT VENT......................................................................................................................................................................20
4.3 SCHEMATIC CHIMNEY INSTALLATION INSTRUCTIONS ....................................................................................................................20
4.4 EXHAUST AND INTAKE RESTRICTION ADJUSTMENT ....................................................................................................................... 23
4.5 FLEXIBLE VENT HORIZONTAL TERMINATION ..................................................................................................................................25
4.6 RIGID PIPE VENTING ARRANGEMENTS........................................................................................................................................... 26
4.7 HORIZONTAL TERMINATIONS.........................................................................................................................................................29
4.8 INSTRUCTIONS FOR VERTICAL TERMINATIONS .............................................................................................................................. 30
4.9 INSTALLATION PROCEDURES ..........................................................................................................................................................33
4.10 GENERAL VENTING SYSTEM INSTALLATION INSPECTION ............................................................................................................. 34
5. FIREPLACE INSTALLATION ............................................................................................................................................................35
5.1 INSTALLATION ITEMS NEEDED........................................................................................................................................................35
5.2 INSTALLATION CODE....................................................................................................................................................................... 37
5.3 LEAK TESTING ................................................................................................................................................................................. 37
5.4 CHECKING GAS PRESSURE .............................................................................................................................................................. 38
6. FINISH..........................................................................................................................................................................................40
6.1 GLASS REMOVAL ............................................................................................................................................................................40
6.2 DECORATIVE GRANULATED GLASS INSTALLATION.......................................................................................................................... 41
7. OPERATING INSTRUCTIONS .........................................................................................................................................................42
7.1 FIRST USE OF YOUR FIREPLACE....................................................................................................................................................... 43
8. CLEANING AND MAINTENANCE ...................................................................................................................................................44
8.1 CLEANING THE GLASS.....................................................................................................................................................................44
9.2 FIREBOX AND BURNER CLEANING ..................................................................................................................................................44
8.3 GLASS REPLACEMENT .................................................................................................................................................................... 46
8.4 BATTERY REPLACEMENT................................................................................................................................................................. 48

6
AMADEO –PROFLAMME 885...................................................................................................................................................49
1. ELECTRICAL WIRING ......................................................................................................................................................................... 50
2. INITIALIZING THE SYSTEM FOR THE FIRST TIME................................................................................................................................ 51
3. LIGHTNING INSTRUCTIONS ..............................................................................................................................................................52
4. REMOTE ...........................................................................................................................................................................................54
5. INSTALLATION PROCEDURE FOR THE CONVERSION KIT................................................................................................................... 58
AMADEO –NOVA 844..................................................................................................................................................................63
1. ELECTRICAL WIRING ......................................................................................................................................................................... 64
2. INITIALIZING THE SYSTEM FOR THE FIRST TIME................................................................................................................................ 65
3. LIGHTNING INSTRUCTIONS ..............................................................................................................................................................66
4. REMOTE ...........................................................................................................................................................................................68
5. INSTALLATION PROCEDURE FOR THE CONVERSION KIT ..................................................................................................................71
TROUBLESHOOTING ........................................................................................................................................................................76
GENERAL TROUBLESHOOTING .........................................................................................................................................................77
SPARE PARTS ...................................................................................................................................................................................78
CHIMNEY ACCESSORIES ...................................................................................................................................................................80
LIMITED LIFETIME WARRANTY ........................................................................................................................................................82

7
INSTALLER MUST READ THIS MANUAL CAREFULLY BEFORE INSTALLING OR OPERATING THIS APPLIANCE.
PLEASE CONSULT LOCAL CODES IF NECESSARY.
1. GENERAL SAFETY INFORMATION
1.1 CARBON MONOXIDE POISONING
Early signs of carbon monoxide poisoning are similar to the flu with headaches, dizziness and nausea. If you have
these signs, the fireplace may not have been installed properly. Turn off the gas fireplace and Get fresh air! Have the
fireplace inspected by a qualified service person. Some people such as pregnant women, people with heart, lungs
diseases, anemia, alcohol dependent, and those who scared of heights are easier and more affected by carbon
monoxide than others.
Propane/LP gas and natural gas are both odorless. An odor-making agent is added to each of these gases. The odor
helps you detect a gas leak. However, the odor added to these gases can fade. Gas may be present even though no
odor exists. So, we strongly recommend that the carbon monoxide detector is installed near this appliance for safety.
The fireplace in this manual that you own now is a direct vent product. Make sure this fireplace will be properly
installed by qualified personnel with license. The glass door must be properly seated and sealed. Combustion leakage
can occur if this unit is not properly installed.
1.2 INSTRUCTIONS
Make sure you read and understand all above warnings. This manual will guide you to safe and proper operation of
this fireplace, please retain it for future reference. This unit is approved for living room, bedrooms, and bathrooms.
Any violation of the following requirement may also cause danger.
1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is convertible
for use with other gases but it has to be done by a qualified service technician using the certified conversion
kit.
2. For propane/LP fireplace, do not place propane/LP supply tank(s) inside any structure. Locate propane/LP
supply tank(s) outdoors. To prevent performance problems, do not use propane/LP fuel tank less than 100
gallons capacity.
3. If you smell gas, please do the following items immediately and exactly :
a.Shut off the gas supply.
b.Do not try to light any appliances.
c. Do not touch any electrical switch; do not use any phone in your building.
d.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
4. Never install the fireplace in a recreational vehicle, high traffic or windy or drafty area, and where curtains,
furniture, clothing, or other flammable objects are less than 42" from the front, top, or sides of the fireplace.
5. This fireplace reaches high temperatures. Keep away from touching any hot surfaces to avoid burns or
clothing ignition. Also since the fireplace will remain hot for a time after shutdown, never touch surfaces
before it cools down.

8
6. Carefully supervise young children and make sure they will not touch and operate any gas fireplace.
7. Installation and any repairs to this fireplace should be carried out by a qualified service person. A
professional service person should be contacted to inspect this fireplace annually. Make it a practice to have
all of your gas fireplaces checked annually.
8. Turn the fireplace off and let it cool before servicing, installing, or repairing. Only a qualified service person
should install, service, or repair the fireplace. Have the burner system inspected annually. If the gas fireplace
needs to be modified, make sure that everything is done correctly according to this manual and the
regulations. Please check and make sure that all the parts of this fireplace are replaced in position before its
operation.
9. Always keep control compartments, burners, and circulating air passages clean. More frequent cleaning may
be needed due to excessive lint and dust from carpeting, bedding material, pet hair, etc. Turn off the fireplace
gas valve and pilot light, cut the gas supply to the gas fireplace before cleaning the fireplace.
10. Have the venting system inspected annually by a qualified service technician before the heating season. If
needed, have venting system cleaned or repaired. See Cleaning and Maintenance. If anything needs to be
changed, you must follow the technician’s advices and make the necessary maintenance and reparations.
11. Never put any combustible materials and any flammable vaporous liquids such as gasoline or alcohol around
your fireplace. Also never place anything on top of fireplace.
12. This fireplace is designed for room heating; never use it to cook food or burn anything.
13. This fireplace is designed to be used with the type of gas indicated on the rating plate; never use any solid
fuels (wood, coal, paper, cardboard, etc.) in this fireplace.
14. All SOLEO Fireplaces, when installed with some electric accessories, must be electrically grounded in
accordance with local codes, in case of the absence of local codes, use the National Electrical Code
(ANSI/NFPA 70), or the Canadian Electrical Code (CSA C22.1).
15. Do not obstruct the flow of combustion and ventilation air in any way.
16. When the appliance is installed directly on carpeting, tile, combustible material other than wood flooring,
you must set the appliance on a sheet metal, wood panel or hearth pad extending the full width and depth of
the appliance.
17. Your fireplace is designed to be used in zero clearance installations. Where air spaces are needed for safety,
standoffs are provided on the fireplace. Combustible materials may be placed against the standoffs. Follow
the installation instructions exactly to prevent fire hazards.
18. This fireplace requires adequate ventilation and combustion air to operate properly.
19. Do not connect this fireplace venting to a chimney flue serving a separate solid-fuel burning fireplace or
appliance.
20. If any part has been exposed to or under water, stop using it and call a qualified service technician to arrange
and replace anything needed as soon as possible.
21. If any log and brick liner is broken, do not operate the fireplace until a qualified service person replace it.
22. Do not use any accessories NOT recommended by the SOLEO Fireplace Company.
23. Do not use a blower insert, heat exchanger insert, or any other accessory not approved for use with this
fireplace.
24. Do not use the fireplace with glass door removed, cracked, or broken.
25. When the fireplace is not in use it is recommended that the gas control valve be set to the “OFF” position.

9
NOTICE
1. During heat-up or cool-down periods, cracking noises may occur, this is normal for
steel heating appliances.
2. It is normal for all gas fireplaces to give off some odor the first time it is burnt. This is
due to the paint and some materials used in the fireplace. When using of this fireplace
for the first time, we strongly suggest that you open the widows in the room where
this appliance is installed.
There are few facts that can help you understand and enjoy this fireplace
* Install and use this fireplace with care. Follow all local codes. In the absence of local codes, use the current
National Fuel Gas Code CAN /CGA-B149 (.1 or .2) Installation codes for Gas Burning Fireplaces and
Equipment. For USAinstallations, follow local codes and/or the current National Fuel Gas Code ANSI Z223.1.
* This fireplace may be installed in any room of your house provided all local codes and these installation
instructions are followed.
* The fireplace must be properly connected to a venting system. The vent pipe installation is very important
to allow for proper operation. You must follow the venting instructions very carefully for either vertical or
horizontal applications.
* This direct-vent gas fireplace is a balanced and sealed gas operating unit. It requires approximately
10-20 minutes of operating time before the flame pattern stabilizes.

10
2. SPECIFICATIONS
2.1 CONSUMPTION, GAS PRESSUREAND EFFICIENCY
INPUT
GAZ NATUREL
(NG)
PROPANE (LP)
Input Rating - BTU/hr
27,000
27,000
Min. Input - BTU/hr
15,000
15,000
Orifice –DMS
#39
#53
GAZ SUPPLY
Manifold pressure
3.8”w.c./0.95kPa
11.0”w.c./2.8kPa
Min. Supply Pressure
5.0”w.c./1.25kPa
12.0”w.c./3.0kPa
Max. Supply Pressure
10.0”w.c./2.5kPa
13.0”w.c./3.3kPa
EFFICIENCY
Maximum Observed Steady Efficiency1
76,80%
78,50%
Steady State Efficiency2
54,10%
55,60%
Annual Fuel Utilization Efficiency [AFUE]3
52,50%
53,60%
Canadian p.4 Efficency3
50,00%
53,30%
1The maximum achievable steady state efficiency can vary depending on the installation and how the fireplace is operated.
2At Min. Input Rate and with Minimum Allowable Vent Length.
3With Minimum Allowable Vent Length.
It is recommended that the pilot flame be turned off if the appliance will not be in use for an extended period of time.
This appliance is equipped for use with the fuel type indicated on the rating place.
This appliance has been certified by OMNI-test Laboratories, Inc. to ANSI Z21.88b-2008 •
CSA 2.33b-2008, Vented Gas Fireplace Heaters, CAN/CGA 2.17-M91, Gas-Fired Appliances for Use at High Altitudes
and CSA P.4.1-02.
These fireplaces are approved for installation at elevations up to 2000 feet in the U.S. and 1370 meters (4500 feet) in
Canada without change. If your installation is at an elevation greater than these, consult with the local authority having
jurisdiction for gas product installations to determine the specific requirements for high altitude installations.

11
2.2 DIMENSIONS OF THE FIREPLACE
Model
A
(mm)
B
(mm)
C
(mm)
D
(mm)
E
(mm)
F
(mm)
G
(mm)
H
(mm)
I
(mm)
J
(mm)
K
(mm)
L
(mm)
AMADEO ST
900
435
930
218
53
363
1057
100
178
1142
246
433
AMADEO 2
900
435
930
218
53
363
1028
100
178
1142
471
433
AMADEO 3
900
435
930
218
53
363
1028
100
178
1142
444
433
AMADEO SEE THROUGH
AMADEO 2 FACES CORNER (LC, RC)
AMADEO 3 FACES

12
3. PREPARING FOR INSTALLATION
3.1 INSTALLATION DESIGN AND PREPARATION
This unit is designed to operate from an On/Off switch or a remote control.
When planning a fireplace installation, it’s necessary to determine:
1- Where the unit is to be installed.
2- The vent system configuration to be used.
3- Gas supply piping configuration.
4- Framing design.
5- Finishing details.
6- Optional accessories (remote control, fan, wall switch).
7- List of installation tools and supply necessary.
8- Appliance and components have to be inspected carefully.
9- Report all defective components to the dealer.
3.2 FRAMING THE FIREPLACE
It is best to build the fireplace framing AFTER the appliance is set in place. Refer to the dimensions relative to
your fireplace. The framing headers may rest on the top of the firebox standoffs.
The firebox may be installed directly on a combustible floor or be raised on a platform of an appropriate height.
Do not place the fireplace on carpeting, vinyl, or other soft floor coverings. It may, however, be placed on a flat
wood, plywood, particle board, or other hard surfaces. Make sure that the firebox rests on a solid continuous
floor or platform with appropriate framing for support. No cold air should enter in the room from under the
firebox.
NOTE: If installed in a mobile home, the fireplace must be bolted securely to the floor.

13
AMADEO-THROUGH INSTALLATION, FLUSH WALLABOVE FIREPLACE –CLEARANCES TO
ADJACENT COMBUSTIBLES

14
AMADEO CORNER INSTALLATION, FLUSH WALLABOVE FIREPLACE –CLEARANCES TO
ADJACENT COMBUSTIBLES

15
AMADEO 3 FACES INSTALLATION, FLUSH WALLABOVE FIREPLACE –CLEARANCES TO
ADJACENT COMBUSTIBLES

16
AMADEO 3 FACES PENINSULA INSTALLATION, ¾” (19mm) MANTEL TRIM, 4” (102mm) MANTEL
OVERHANG –CLEARANCES TO ADJACENT COMBUSTIBLES

17
3.3 CLEARANCES TO COMBUSTIBLES
WARNING
Follow these instructions carefully to ensure safe installation. Failure to follow instructions exactly can create a fire
hazard. The appliance cannot be installed on a carpet, tile or other combustible material other than wood flooring. If
installed on carpet or vinyl flooring, the appliance shall be installed on a metal, wood or noncombustible material panel
extending full width and depth of the appliance.
CAUTION
The combustible area above the facing must not protrude more than 3/4" from the facing. If it does, it is considered a
mantel and must meet the mantel requirements listed in this manual.
1) For ease of installation, frame your fireplace after it is positioned and the vent system is installed.
Remember to install the top standoffs.
CAUTION
Verify your fireplace dimensions, frame methods and finished wall facing details before framing. Determine the total
thickness of facing material - drywall plus ceramic tiles, slate, etc. Allow the finish surface to be flush with the front or
side of the unit.
2) When locating your appliance on an exterior wall or in a chase, apply a vapor barrier and drywall as per
local building codes. DO NOT INSULATE THE FIREPLACE ITSELF.
MINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION
Fireplace Glass Faces to Opposing Walls –All Models
38” (965mm)
Fireplace Face at Vent End to Adjacent Wall –All Models
5” (127mm)
Fireplace Top to Ceiling –All Models
10.5” (267mm)
Vent Pipe to Ceiling –All Models
4.5” (114mm)
Fireplace Back Wall to Adjacent Materials –Model 122
1” (25mm)
Fireplace Trim to Back Wall Filler Piece –Model 122
0.25” (6.4mm)
Mantel Clearances (See Adjacent Illustration)
A
13” (330mm)
V
10” (254mm)
B
11” (279mm)
W
8” (203mm)
C
9” (229mm)
X
6” (152mm)
D
7” (179mm)
Y
4” (101mm)
E
5’’ (127mm)
Z
2’’ (51mm)

18
CAUTION
The unit does not have to be completely enclosed in a chase. The clearance on top of the unit is 0" to the
standoffs so combustible building materials can be laid directly on top of the standoffs. You must maintain
clearance from the vent to combustible materials.
3.4 TOP CLEARANCES
The top and air intake side stand-offs for the multi-sided gas fireplace are shipped from the factory in the
folded-down position. They must be unfolded and secured in the full-up position before the fireplace is installed.
Two sheet metal screws are provided to secure each stand-off in the extended position. Please refer to the
illustrations below.
Stand-offs in the shipping position (folded-down)
Stand-offs in the extended position (unfolded and secured with screws)

19
3.5 FINISHING MATERIAL
WARNING
Any remote wiring (i.e. remote control, wall switch) must be done prior to final finishing to avoid costly reconstruction.
WARNING
Never obstruct or modify the air inlet or outlet, this may create a fire hazard.
Only noncombustible materials (i.e. brick, tile, slate, steel, or other materials with a UL fire rating of Zero) may be used to cover the
black-painted faces of the appliance.
4. INSTALLATION OF THE VENT SYSTEM
WARNING
Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious
injury, property damage or loss of life. Operation of improperly installed and maintained venting system could result in
serious injury, property damage or loss of life.
CAUTION
Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious
injury, property damage or loss of life. Operation of improperly installed and maintained venting system could result in
serious injury, property damage or loss of life.
4.1 INSTALLATION PRECAUTIONS
NOTE: This appliance must be installed with an I NDUSTRI ES SO CA INC .approved venting system only.
Consult local building codes before beginning the installation. The installer must make sure to select the proper vent system for
installation. Before installing vent kit, the installer must read this fireplace manual and vent kit instructions. Only a qualified
installer/service person should install venting systems. The installer must follow these safety rules:
. Wear gloves and safety glasses for protection.
. Use extreme caution when using ladders or when on rooftops.
. Be aware of electrical wiring locations in walls and ceilings.
The following actions will void the warranty on your venting system:
.Installation of any damaged venting component.
. Unauthorized modification of the venting system.
. Installation of any component, part not manufactured or approved by IN D U S T RI E S SO C A I N C .
. Installation other than permitted by these instructions.

20
4.2 LOCATION OUT VENT
VENT TERMINAL CLEARANCES
Venting terminals shall not be recessed into a wall or siding
VENT TERMINAL CLEARANCES