Sonifex HY-03DTD User manual

HY-03DTD Fitting & Configuration
HY-03DTD Fitting & Configuration
Enabling Dial Tone Disconnect on the HY-03
On the rear panel of the HY-03 is a set of 4 DIP switches These switches are used to configure the HY-03 in the modes
that you want it to operate A label on the top panel of the unit shows the orientation of the switches :
Figure 1-1 : Configuration Settings Switches
To enable the dial tone disconnect option, set switch SW1 to ON When enabled (ON), the HY-03 will automatically
disconnect from the telephone line when an appropriate dial tone is detected
Configuring the Dial Tone Disconnect oard
To configure the dial tone disconnect board, the appropriate jumper(s) JP1-JP16 on the Dial Tone Disconnect PCB must
be fitted to enable detection of the required tone(s) in the country in which the HY-03 is being used, or for the equipment
to which the HY-03 is to be connected For example, to enable the HY-03 to detect the dial tone in Finland, set the
jumpers for JP1, JP2 and JP3
Figure 1-2 : Jumper settings on the HY-03DTD board
See Table 1-1 below for a list of the tones currently implemented
Country or
Equipment Type
Frequencies Type Details Jumper(s) set on
JP…
Austria 440Hz Continuous - 1
Avaya PBX 400Hz Cadence 375ms on, 375ms pause 2 + 3 + 4 + 5
Belgium 450Hz Continuous - 2
Bulgaria 425Hz Cadence 250ms on, 750ms pause,
750ms on, 1000ms pause
1 + 2
Cyprus 350Hz and 450Hz Continuous - 3
Czech Republic 425Hz Continuous - 1 + 3
Denmark 425Hz Continuous - 2 + 3
Finland 425Hz Continuous - 1 + 2 + 3
France 440Hz Continuous - 4
Germany 425Hz Continuous - 1 + 4
Greece 440Hz Continuous - 2 + 4
Hungary 440Hz Continuous - 1 + 2 + 4
Iceland 425Hz Continuous - 3 + 4
India 400Hz Cadence 750ms on, 750ms pause 1 + 3 + 4 + 5
Ireland 400Hz and 450Hz Continuous - 1 + 3 + 4
Israel 400Hz Continuous - 1 + 4 + 5
Italy 425Hz Cadence 200ms on, 200ms pause,
600ms on, 1000ms pause
2 + 3 + 4
Italy2 425Hz Cadence 200ms on, 200ms pause 1 + 2 + 3 + 4 + 5
Italy PBX 425Hz Cadence 500ms (+-20ms) on, 500ms 6
Sonifex HY-03DTD User Handbook 1
Plug-in
Header
Mounting screw
on a pillar
JP1JP16

HY-03DTD Fitting & Configuration
(+-20ms) off
Japan 400Hz Continuous - 2 + 4 + 5
Luxembourg 425Hz Continuous - 1 + 2 + 3 + 4
Netherlands 450Hz Continuous - 5
Norway 425Hz Continuous - 1 + 5
Poland 425Hz Continuous - 2 + 5
Portugal 425Hz Continuous - 1 + 2 + 5
South Korea 350Hz and 440Hz Continuous - 1 + 2 + 4 + 5
Spain 425Hz Continuous - 3 + 5
Sweden 425Hz Continuous - 1 + 3 + 5
Switzerland 425Hz Continuous - 2 + 3 + 5
Taiwan 350Hz and 440Hz Continuous - 3 + 4 + 5
United Kingdom 350Hz and 440Hz Continuous & Cadence 750ms on, 750ms pause 1 + 2 + 3 + 5
UK PBX 425Hz Cadence 480 ms on, 480ms pause 6 + 1
United States 440Hz and 480Hz Continuous - 4 + 5
Table 1-1 : Supported Dial Tone Details
The unit can be programmed with other settings, so please contact us if you need the settings for a different country to
be implemented In this case, it would be useful to have an audio recording of the dial-tone and a specification of the dial
tone parameters
Fitting the HY-03DTD oard
Warning : The power must be switched off at the supply or the power lead must be disconnected before attempting to
open the unit Removal of the cover can expose dangerous voltages
Warning : The telephone line plug should be disconnected from the telecommunications network exchange line before
removing the cover
To open the HY-03, simply remove the 4 screws in the corners of the rear panel The rear panel and main PCB will slide
backwards out of the metal chassis
Figure 1-3 : HY-03 Preset Controls and Alignments
Fit the HY-03DTD board onto the main HY-03 PCB as shown above Make sure that there is a secure and firm connection
between the plug-in headers, and fix the supplied threaded M3 x 12mm pillar between the two boards using the supplied
M3 x 6mm pan head posidrive screws (one top and one bottom)
2 Sonifex HY-03DTD User Handbook
Mic Gain
Limit Level
Noise Gate
Disable
Res Auto
Disable
Line
Reverse
K-Break
Cap Auto
Disable
Noise Gate
Threshold
Optional
HY-03DTD
Board
On units serial number
HY000323 upwards
Plug-in
Header
Mounting screw
on a pillar
Output
Level
Sample
Threshold Rings
Res Set
Cap Set
RV4
RV7
RV2
JP1
JP4JP5
JP1JP16
JP2 JP3
RV6
RV5 RV8
RV3 RV1

HY-03DTD Fitting & Configuration
Then, reinsert the main HY-03 PCB back into the chassis When re-inserting the main PCB, ensure that the PCB edges are
in the runners inside the chassis and also that the front panel LED and divert button are in the correct place in the front
panel The HY-03 should now automatically detect the dial-tone
If you have any problems, contact technical support on technical support@sonifex co uk
V1 03 HY-03DTD handbook © Sonifex Ltd, 2009
Sonifex Ltd, 61, Station Road, Irthlingborough, Northants, NN9 5QE, UK
T: [phone] F:[phone] E: technical support@sonifex co uk I: www sonifex co uk
Sonifex HY-03DTD User Handbook 3