SonoSite Edge Stant H-Universal Stand User manual

1
Edge Stand
H-Universal Stand
Assembly Instructions
Introduction
Assembly for the Edge™ Stand or H-Universal™ Stand
includes the base, column, and system platform.
You can install optional peripherals and accessories on
the stand; refer to their separate installation
instructions. Each product is packaged separately. If
installing multiple products on the stand, you may
receive duplicate tools, cords, and instructions across
kits. Please disregard any duplicates.
Install products in the order listed on the enclosed
insert Installation sequence of products on the stand.
Assembly is easiest with more than one person.
See the stand’s user guide for information on setting
up the ultrasound system to use accessories and
peripherals and for information on cleaning and
disinfecting.
Assembled H-Universal Stand. Shown with M-Turbo®
ultrasound system and optional basket, black-&-
white printer, and Triple Transducer Connect.
Contents
See also “Cables and connectors” on page4.
Description
(Quantity)
Illustration
Column
(1)
Base
(1)
System
platform
(1)
Storage cup
(4)
Cord catch
pre-installed
(4)
Cord hook
(2)
Back plate for
cord hook
(2)
Stand hook
(2)

2
Tools included
Assembly
1 Lock wheels.
Press down the lever on two or more wheels.
2 Attach column to base.
1Orient the back of the column with the back of the
base.
The back of the base has the SonoSite logo.
The back of the column has a lever at the top.
2Without pinching the cords, slide the column onto
the two pegs on the base. Place the cords in the
side grooves of the column.
3Insert the Allen bit into the magnetic wrench.
4Place a 12mm Allen-head screw onto the
magnetic wrench.
Placing the screw onto the magnetic wrench helps
prevent it from falling into the stand.
5Insert the screw into the hole at the lower front of
the column, and tighten.
The last few turns require additional force because
of a special coating on the screws. The coating
helps prevent them from coming loose.
6Using the magnetic wrench, insert and tighten the
three additional 12mm Allen-head screws into the
column: One at the back, and one on each side.
3 Attach system platform.
1Place the system platform onto the column: Insert
the column pole into the cylinder, aligning the peg
on the pole with the notch on the cylinder.
2Using the tamper resistant Allen wrench, tighten
the following:
• 1/2” hex bolt into the back of the cylinder
• Two preinstalled set screws on the front of the
cylinder
3Insert the four cups: Align the grooves and press
into place.
4Insert the small end of a hook into the slot at the
front of the system platform, and push it down
into place. Repeat for other side.
4 Insert system and attach mini-dock.
1Insert the ultrasound system:
aRotate system latches outward.
1/2” tamper-
resistant screw
(1)
12mm Allen-
head screw
(4)
Cord-hook
screw
(2)
Description Illustration
Magnetic
wrench
Allen bit
5/32” tamper-
resistant Allen
wrench Set screws
Cup
Hook
Cup

3
bPlace the ultrasound system on the system
platform, ensuring that the transducer cable is
positioned between the handles of the stand.
cSecure the system by rotating the system
latches inward.
2Attach the mini-dock if using AC-powered
peripherals:
aPlace the mini-dock on the system platform.
bSlide the mini-dock feet under the ultrasound
system, and firmly press the mini-dock into the
I/O connector on the back of the system.
The mini-dock is correctly attached when there
is no gap between the system and mini-dock.
5 Connect remaining cables.
See also “Connectivity” on page4.
1Connect the DC power supply cord (A).
2Connect the system power cord (K) to a hospital-
grade electrical outlet.
6 Secure cables.
1Remove cord catches from column sides: Turn
catches counter-clockwise and pull.
2Place the system cable (and any other cables, such
as accessory cables) into the groove on either side
of the column.
3Attach each cord hook:
The cord hooks are for holding the system cord
when not in use.
aAssemble the cord hook with a screw and back
plate as below:
Insert the screw only until it is flush with the
back plate.
bInsert the back plate of the cord hook into the
lower opening of the column side, oriented as
below.
The first cord hook faces upward, and the
second faces downward.
The edges of the back plate grip the column.
Insert the hooks on whichever side of the
column best suits your setup (for example, has
more space).
cSlide the hook up the column to the desired
location, and then tighten the screw using a
Phillips screwdriver.
Tip:As you slide the hook, pull it toward you to
maintain proper orientation.
4Re-attach cord catches: Insert each cord catch into
the side slot on the column where desired, and
turn clockwise to secure.
Cord catches help to keep the cables in the
column.
System latch
System
Mini-dock
Installed cord hooks.
The first points upward,
and the second
downward.

4
Connectivity
Cables and connectors
Table 1: Connectivity Symbols on Mini-Dock
Edge, H-Universal, M-Turbo, SonoSite, and the SonoSite logo are
registered (in some jurisdictions) and unregistered trademarks
owned by SonoSite, Inc.
Non-SonoSite product names may be trademarks or registered
trademarks of their respective owners.
The SonoSite ultrasound systems referenced in this document may
be covered by one or more of the following U.S. patents: 5722412,
5817024, 5893363, 6135961, 6203498, 6364839, 6371918, 6383139,
6416475, 6447451, 6471651, 6569101, 6648826, 6575908, 6604630,
6817982, 6835177, 6962566, 7169108, 7449640, 7534211, 7549961,
7588541, 7591786, 7604596, 7643040, 7686766, 7694814, 7727153,
7740586, 7804970, 7809400, 7819807, 7841575, 7849250, 7867168,
7883276, D456509, D461895, D509900, D538432, D544962,
D558351, D559390, D591423, D592750, D592760, D625014,
D625015, and by the following counterpart foreign patents:
AU727381, AU730822, CA2372152, CA2372158, CA2373065, CN ZL
97113678.5, CN ZL 98106133.8, CN ZL 98108973.9, CN ZL
200830007734.8, DE60021552.0, DE60029777.2, DE60034670.6,
DE69730563.5, DE6980539.6, DE69831698.3, DE60 2004 23 816.3-08,
FR0815793, FR0875203, FR0881492, FR1175713, FR1180970,
FR1589878, GB0875203, GB0881492, GB1175713, GB1180970,
GB1180971, GB1589878, IT0815793, IT0881492, IT1175713,
IT1589878, KR528102, KR532359, NO326202, NO326814, NZ542968,
RCD000897368-0001, SP0815793, SP0881492, SP1589878. Patents
pending.
WARNING: To avoid the risk of a shock hazard, do
not plug the power cord of the stand
into a multiple portable socket outlet
(MPSO) or into an extension cord.
Caution: To avoid damaging the system, use
only accessories and peripherals
recommended by SonoSite with the
ultrasound system.
Symbol Definition
DC input
Print control
USB
Ethernet
RS-232 (DVD recorder or bar code
scanner)
S-video out
S-video in
DVI video out
Composite video out
Audio out
ECG/Footswitch
SonoSite, Inc.
21919 30th Drive SE
Bothell, WA 98021 USA
T: 1-888-482-9449 or
1-425-951-1200
F: 1-425-951-1201
SonoSite Ltd
Alexander House
40A Wilbury Way
Hitchin, Herts
SG4 OAP UK
T: [phone]
F: [phone]
10/2011
Copyright 2011 by
SonoSite, Inc.
All rights reserved. 
P12434-02
*P12434-02*
Table 2: Cables and Connectors
Cable
[Letter]
[Name]
[Length]
[Illustration]
Connector 1
[Illustration]
[Connects to]
Connector 2
[Illustration]
[Connects to]
A
DC power
supply cord
6.8 ft./2 m
See “Contents”
on page1.
System
or mini-dock
Pre-installed
J
AC power cord
39 in./1 m
See “Contents”
on page1.
AC-powered
peripheral
Pre-installed
K
System AC
power cord
10 ft./3 m AC connector on
rear of stand base
Wall outlet
Caution: Federal (United States) law restricts
this device to sale by or on the order
of a physician.