d & b audiotechnik Z Series User manual

ZZ5054
Mounting instructions 2.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
Z5054 Mounting instructions
Version: 2.1 en, 04/2020, D2946.EN.01
Copyright © 2020 by d&b audiotechnik GmbH & Co. KG; all
rights reserved.
Keep this document with the product or in a safe place
so that it is available for future reference.
When reselling this product, hand over this document to the new
owner.
d&b audiotechnik GmbH & Co. KG
Eugen-Adolff-Str. 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1 Z5054 Flying adapter........................................................ 4
1.1 Scope of supply.......................................................................... 4
1.2 Safety precautions...................................................................... 4
1.3 Intended use................................................................................ 5
1.4 Assembly..................................................................................... 5
1.5 Operation.................................................................................... 5
2 Manufacturer's declarations........................................... 6
2.1 EU conformity (CE symbol)........................................................ 6
2.2 Disposal....................................................................................... 6
Contents
d&b Z5054 Mounting instructions 2.1 en 3

1.1 Scope of supply
Pos. Qty. d&b Code Description
[1] 1 Z5054 Flying adapter
including:
[2] 4 M10 x 25 Hex head bolt
[3] 4 Plain washer
[4] 4 Self-securing nut M10
1 D2946.EN.01 Z5054 Mounting instructions
Weight 2.2 kg (4.9 lb)
1.2 Safety precautions
General safety
Installation and setup should only be carried out by qualified and
authorized personnel observing the valid national Rules for the
Prevention of Accidents (RPA).
It is the responsibility of the person installing the assembly to ensure
that the suspension/fixing points are suitable for the intended use.
Always carry out a visual and functional inspection of the items
before use. In case there is any doubt as to the proper functioning
and safety of the items, these must be withdrawn from use
immediately.
Load safety information
The maximum permitted safe working load (SWL) for the adaptor
is 65 kg/143.3 lb. This is equivalent to the combined weight of
two applicable cabinets, two applicable horizontal brackets and
one Z5552 bracket connector. This value must under no
circumstances be exceeded. Secondary safety should always be
provided and used when flying or fixing loudspeaker loads
overhead.
Scope of supply
1 Z5054 Flying adapter
d&b Z5054 Mounting instructions 2.1 en4

1.3 Intended use
The flying adapter is intended to suspend loudspeakers mounted to
horizontal brackets at a precisely defined vertical flying angle. The
flying adapter can be:
▪ flown using the Z5015 TV spigot 02 in conjunction with Z5012
Pipe clamp.
▪ flown using the Z5147 Rota clamp.
Applicable horizontal brackets:
▪ Z5388 VP Horizontal bracket
▪ Z5398 YP Horizontal bracket
▪ Z5409 Horizontal bracket 10S
▪ Z5411 Horizontal bracket 12S
▪ Z5554 Horizontal bracket 24S
1.4 Assembly
Tools required:
▪ Open-ended or ring spanner/wrench SW 17 mm.
Fixing bolts with a thread length of more than 25 mm must not be
used.
ÞThe flying adapter [1] is bolted to the four holes at the rear of
the horizontal bracket using the four hex head bolts [2], the
plain washers [3] and the self-locking nuts [4].
1.5 Operation
The flying adapter is equipped with eleven locating holes (12 mm)
at 30 mm spacing. The vertical flying angle depends on which of
these holes is used as the flying point of the cabinet - the resulting
angles, upwards (positive angle) or downwards (negative angle),
are shown in the graphic opposite. The loudspeaker will adopt a
stable vertical position without the need for additional stabilizing
guy lines. A 24 mm hole is provided at the rear of the adapter for
securing cables.
Intended use
Assembly
Hole index of the flying adapter
d&b Z5054 Mounting instructions 2.1 en 5

2.1 EU conformity (CE symbol)
This declaration applies to:
d&b Z5054 Flying adapter
manufactured by d&b audiotechnik GmbH & Co. KG.
All product variants are included, provided they correspond to the
original technical version and have not been subject to any later
design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered
from d&b or downloaded from the d&b website at
www.dbaudio.com.
2.2 Disposal
When out of use the rigging components must be disposed of in
accordance with the national environmental regulations.
Ensure that damaged rigging components are disposed of in a
way that they cannot be used again.
2 Manufacturer's declarations
d&b Z5054 Mounting instructions 2.1 en6

D2946.EN.01, 04/2020 © d&b audiotechnik GmbH & Co. KG
www.dbaudio.com