Sony Dcr-ip210 User manual

SERVICE MANUAL

DIGITAL VIDEO CAMERA RECORDER

V MECHANISM

LEVEL 2

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (992999551.pdf).

• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (992999541.pdf).

• For MECHANISM ADJUSTMENTS, refer to the “MICRO MV MECHANICAL ADJUSTMENT MANUAL 1

V MECHANISM ” (9-929-911-11).

• Reference No. search on printed wiring boards is available.

• Table for differences of function of each model.

Link

SERVICE NOTE

DISASSEMBLY

BLOCK DIAGRAMS

FRAME SCHEMATIC DIAGRAMS

SCHEMATIC DIAGRAMS

PRINTED WIRING BOARDSSPECIFICATIONS

REPAIR PARTS LIST

SERVICE NOTE

DISASSEMBLY

BLOCK DIAGRAMS

FRAME SCHEMATIC DIAGRAMS

SCHEMATIC DIAGRAMS

PRINTED WIRING BOARDS

REPAIR PARTS LIST

SPECIFICATIONS

Link

Revision History

Ver 1.0 2002. 09

On the CD-406, DI-087 andVC-308 board

This service manual provides the information that is premised the circuit board replacement service and not intended repair

inside the CD-406, DI-087 and VC-308 board.

Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the

CD-406,

DI-087 and VC-308

board are not shown.

The following pages are not shown.

Schematic diagram .............................Pages 4-25 to 4-78

Mounted parts location

Pages 4-114 to 4-116

Printed wiring board............................Pages 4-97 to 4-106 Electrical parts list Pages 5-18 to 5-30

Waveforms ...........................................

Pages 4-110 to 4-111

DCR-IP210/IP210E/

IP220/IP220E

RMT-817

US Model

Canadian Model

DCR-IP220

AEP Model

UK Model

Australian Model

DCR-IP220E

East European Model

DCR-IP210E/IP220E

Tourist Model

DCR-IP210/IP210E

E Model

DCR-IP210/IP210E/IP220/IP220E

Chinese Model

DCR-IP210E

Korea Model

DCR-IP210

Hong Kong Model

DCR-IP210/IP220E

Photo : DCR-IP220E

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

—2 —

DCR-IP210/IP210E/IP220/IP220E

SPECIFICATIONS

SAFETY-RELATED COMPONENTWARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH

MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

COVER

CAUTION :

Dangerofexplosion if batteryisincorrectlyreplaced.

Replace only with the same or equivalent type.

Video camera

recorder

System

Video recording system

2 rotary heads

Helical scanning system

Audio recording system

MPEG1 Audio Layer2

(Fs 48 kHz, stereo)

Video signal

DCR-IP210/IP220:

NTSC color, EIA standards

DCR-IP210E/IP220E:

PAL colour, CCIR standards

Usable cassette

MICROMV cassette with the

mark printed

Tape speed

Approx. 5.66 mm/s

Recording/playback time

(using cassette MGR60)

1 hour

Fastforward/rewind time

(using cassette MGR60)

Approx. 1 min. and 30 seconds

Viewfinder

Electric viewfinder (colour)

Image device

5.0 mm (1/3.6 type) CCD

(Charge Coupled Device)

Gross: Approx. 2 110 000 pixels

Effective (still):

Approx. 1 920 000 pixels

Effective (moving):

Approx. 1 080 000 pixels

Lens

Carl Zeiss Vario-Sonnar T*

Combined power zoom lens

Filter diameter 37 mm (1 13/16 in.)

10×(Optical), 120×(Digital)

Focal length

4.5 – 45 mm (3/16 – 1 13/16 in.)

When converted to a 35 mm still

camera

CAMERA:

52 – 520 mm (2 1/8 – 20 1/2 in.)

MEMORY:

39 – 390 mm (1 11/16 – 16 5/8 in.)

Colour temperature

AUTO, HOLD, INDOOR

(3 200K), OUTDOOR (5 800K)

Minimum illumination

7 lx (lux) (F 1.8)

0 lx (lux) (in the NightShot mode)*

* Objects unable to be seen due to

the dark can be shot with infrared

lighting.

Input/Output connectors

Audio/Video input/output

10-pin connector

Input/output auto switch

Video signal: 1 Vp-p, 75 Ω(ohms),

unbalanced, sync negative

Luminance signal: 1 Vp-p, 75 Ω

(ohms), unbalanced

Chrominance signal:

DCR-IP210/IP220: 0.286 Vp-p,

DCR-IP210E/IP220E: 0.3 Vp-p,

75 Ω (ohms), unbalanced

Audio signal: 327 mV, (at output

impedance more than 47 kΩ

(kilohms))

Input impedance with more than

47 kΩ(kilohms)

Output impedance with less than

2.2 kΩ(kilohms)

i.LINK (MICROMV Interface)

input/output

4-pin connector S400

LANC jack

Stereo mini-minijack (ø 2.5 mm)

USB jack

mini-B

Headphone jack

Stereo minijack (ø 3.5 mm)

LCD screen

Picture

6.2 cm (2.5 type)

Total dot number

211 200 (960 ×220)

Wireless communication

(DCR-IP220/IP220E only)

Communication system

Bluetooth specification Ver.1.1

Maximum communication

speed

1) 2)

Approx. 723 kbps

Maximum output

Bluetooth specification Power

Class2

Communication distance

Approx. 10 m (33 feet) (Open space,

when using a Sony BTA-NW1/

NW1A Modem Adaptor with

Bluetooth Function)

Compatible Bluetooth profiles

Generic Access Profile

Dial-up Networking Profile

Usable frequency band

2.4 GHz band

(2.400 – 2.483 5 GHz)

The maximum rate defined by

Bluetooth specification Ver.1.1

Depends on obstacles between the

Bluetooth devices, radio wave

conditions, etc.

Defined by Bluetooth

specification for intended use

between the Bluetooth devices

General

Power requirements

7.2 V (battery pack)

8.4 V (AC power adaptor)

Average power consumption

(when using the battery pack)

During camera recording using

LCD: 4.8 W

Viewfinder: 4.2 W

Operating temperature

0°C to 40°C (32°F to 104°F)

Storage temperature

–20°C to +60°C (–4°F to +140°F)

Dimensions (approx.)

98 ×75.5 ×136 mm

(3 7/8 ×3 ×5 3/8 in.) (w/h/d)

Mass (approx.)

520 g (1 lb 2 oz)

excluding the battery pack and

cassette

630 g (1 lb 6 oz)

including the battery pack,

NP-FF70, cassette MGR60, lens cap

and stylus

Supplied accessories

See page 4.

AC power adaptor

Power requirements

100 – 240 V AC, 50/60 Hz

Power consumption

23 W

Output voltage

DC OUT: 8.4 V, 1.5 A in the

operating mode

Operating temperature

0°C to 40°C (32°F to 104°F)

Storage temperature

–20°C to +60°C (–4°F to +140°F)

Dimensions (approx.)

125 ×39 ×62 mm (5 ×1 9/16 ×2 1/2

in.) (w/h/d) excluding projecting

parts

Mass (approx.)

280 g (9.8 oz)

excluding mains lead

Battery pack

Maximum output voltage

DC 8.4 V

Output voltage

DC 7.2 V

Capacity

9.6 Wh (1 350 mAh)

Operating temperature

0°C to 40°C (32°F to 104°F)

Dimensions (approx.)

40.8 ×24.1 ×49.1 mm

(1 5/8 ×31/32 ×1 15/16 in.)

(w/h/d)

Mass (approx.)

90 g (3.2 oz)

Type

Lithium ion

“Memory Stick”

Memory

Flash memory

8MB: MSA-8A

Operating voltage

2.7 – 3.6 V

Power consumption

Approx. 45 mA in the operating

mode

Approx. 130 µA in the standby

mode

Dimensions (approx.)

50 ×2.8 ×21.5 mm

(2 ×1/8 ×7/8 in.) (w/h/d)

Mass (approx.)

4 g (0.14 oz)

Design and specifications are

subject to change without notice.

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

—3 —

DCR-IP210/IP210E/IP220/IP220E

1. Check the areaof your repairfor unsoldered orpoorly-soldered

connections. Check the entireboard surface for soldersplashes

and bridges.

2. Check the interboard wiring to ensure that no wires are

"pinched" or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which,through functioning, show obvious signs

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350°C.

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than

ordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

DCR-IP210

E/HK/KR/JE

NTSC

DCR-

IP210E

EE/E/JE/CH

PAL

16Mbit

DCR-IP220E

AEP/UK/EE/

E/AUS/HK

PAL

1AC-L20A AC power adaptor (1), Mains lead (1)

2NP-FF70 battery pack (1)

3A/V connecting cable (1)

4Wireless Remote Commander (1)

5R6 (Size AA) batteries for the Remote

Commander (2)

6Lens cap (1)

7Lens hood (1)

8“Memory Stick” (1)

9USB cable (1)

q; CD-ROM (SPVD-008 USB Driver) (1)

qa CD-ROM (Movie Shaker Ver.3.1 for

MICROMV) (1)

qs Cleaning cloth (1)

qd Stylus (1) (DCR-IP220/IP220E only)

qf 21-pin adaptor (1) (AEP, UK, EE model only)

qsqa

qg qh

qg 2-pin conversion adaptor (1)

(DCR-IP210 : JE/IP210E : JE only)

qh 2-pin conversion adaptor (1)

(DCR-IP210 : E, HK/IP210E : E/

IP220 : E/ IP220E : E, HK)

•Abbreviation

CND : Canadian model

EE : East European model

HK : Hong Kong model

AUS : Australian model

JE : Tourist model

CH : Chinese model

KR : Korea model

Table for difference of function

•SUPPLIED ACCESSORIES

Makesure thatthe followingaccessories are suppliedwith yourcamcorder.

Model

Destination

Color System

NETWORK

(Bluetooth)

BT-012, AN-025 boards

Flash memory

(VC-308 board IC-904)

DCR-IP220

US/CND/E

NTSC

Remark

With BT-012,

AN-025 boards

64Mbit

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

—4 —

DCR-IP210/IP210E/IP220/IP220E

TABLE OF CONTENTS

1. SERVICE NOTE

1-1. SERVICE NOTE ·····························································1-1

1. POWER SUPPLY DURING REPAIRS ··························1-1

2. TO TAKE OUTA CASSETTE WHEN NOT EJECT

(FORCE EJECT) ·····························································1-1

3. DISCHARGING OF THE FLASHLIGHT POWER

SUPPLY CAPACITOR ···················································1-2

3-1. PREPARING THE SHORT JIG ······································1-2

3-2. DISCHARGING THE CAPACITOR······························1-2

4. HOW TO OPEN THE FLASH WHEN THE FLASH

DOESN’T OPEN ····························································1-2

5. COAXIAL CONNECTOR OF THE BLUETOOTH

HARNESS·······································································1-2

6. NOTES ON HANDLING THE LASER DIODE·······1-3

[LASER UNIT (D5104)]················································1-3

6-1. Soldering Conditions of Laser Unit (D5104) ··················1-3

1-2. SELF-DIAGNOSIS FUNCTION····································1-4

1. SELF-DIAGNOSIS FUNCTION ····································1-4

2. SELF-DIAGNOSIS DISPLAY ·······································1-4

3. SERVICE MODE DISPLAY ··········································1-4

3-1. Display Method ·······························································1-4

3-2. Backup No. ······································································1-4

3-3. End of Display·································································1-4

4. SELF-DIAGNOSIS CODE TABLE································1-5

2. DISASSEMBLY

2-1. LCD UNIT (PD-166 BOARD) ·······································2-3

2-2. FRONT CAP ASSEMBLY··············································2-4

2-3. CABINET (F) BLOCK ASSEMBLY-1···························2-4

2-4. CABINET (F) BLOCK ASSEMBLY-2···························2-5

2-5. EVF COVER ASSEMBLY (FP-539 BOARD) ···············2-5

2-6. CABINET (UPPER) BLOCK ASSEMBLY ···················2-6

2-7. LD-112 BOARD ·····························································2-7

2-8. EMBLEM CABINET ASSEMBLY ································2-8

2-9. VF BLOCK ASSEMBLY················································2-8

2-10. VF-155 BOARD······························································2-9

2-11. AN-025 BOARD (IP220/IP220E), DC-098 BOARD ···2-10

2-12. VF BLOCK ASSEMBLY, BT HOLDER BLOCK

ASSEMBLY, LENS BLOCK ASSEMBLY, CABINET

(LOWER) BLOCK ASSEMBLY ··································2-11

2-13. VF BLOCK ASSEMBLY, BT HOLDER BLOCK

ASSEMBLY ··································································2-12

2-14. LENS BLOCK ASSEMBLY········································2-12

2-15. CD-406 BOARD ···························································2-13

2-16. CABINET (REAR) BLOCK ASSEMBLY ···················2-14

2-17. DI-087 BOARD·····························································2-15

2-18. VC-380 BOARD, JK-234 BOARD·······························2-17

2-19. MECHANISM DECK (V100) ······································2-17

2-20. CABINET (L) BLOCK ASSEMBLY ···························2-20

2-21. CONTROL SWITCH BLOCK (PW-2980)···················2-21

2-22. ST-076 BOARD ····························································2-21

2-23. FP-541 BOARD ····························································2-22

2-24. FLASH UNIT (FL-2980) -1 ··········································2-23

2-25. FLASH UNIT (FL-2980) -2 ··········································2-24

2-26. BT-012 BOARD (IP220/IP220E)··································2-25

2-27. FP-538 BOARD ····························································2-26

2-28. 760A (CZ) BLOCK ASSEMBLY ·································2-27

2-29. GMR SENSOR (M) ······················································2-28

2-30. IRIS FLEXIBLE ASSEMBLY (760) ····························2-29

2-31. CONTROL SWITCH BLOCK (SS-2980) ····················2-30

2-32. PK-067 BOARD, SW-380 BOARD,

HINGE ASSEMBLY ·····················································2-31

2-33. CIRCUIT BOARDS LOCATION ·································2-32

2-34. FLEXIBLE BOARDS LOCATION ······························2-33

3. BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/5) ···························3-1

3-2. OVERALL BLOCK DIAGRAM (2/5) ···························3-3

3-3. OVERALL BLOCK DIAGRAM (3/5) ···························3-5

3-4. OVERALL BLOCK DIAGRAM (4/5) ···························3-7

3-5. OVERALL BLOCK DIAGRAM (5/5) ···························3-9

3-6. POWER BLOCK DIAGRAM (1/2) ······························3-11

3-7. POWER BLOCK DIAGRAM (2/2) ······························3-13

4. PRINTEDWIRING BOARDS AND

SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM (1/3) ·······················4-1

FRAME SCHEMATIC DIAGRAM (2/3) ·······················4-3

FRAME SCHEMATIC DIAGRAM (3/3) ·······················4-5

4-2. SCHEMATIC DIAGRAMS

•BT-012 (BLUETOOTH MODULE), AN-025 (AN-

TENNA), FP-538, FP-539, FP-554

SCHEMATIC DIAGRAM ······························4-9

•LD-112 (FOCUS, ZOOM, IRIS, ND FILTER CON-

TROL) SCHEMATIC DIAGRAM ····························4-11

•ST-076 (IR LED DRIVE), fP-541, FP-542, FL-2980

SCHEMATIC DIAGRAM ····························4-13

•JK-234 (JACK BOARD)

SCHEMATIC DIAGRAM ····························4-15

•PD-166 (RGB DRIVE/TG)

SCHEMATIC DIAGRAM ····························4-17

•VF-155 (PITCH/YAW SENSOR, AMP, EVF)

SCHEMATIC DIAGRAM ····························4-19

•CONTROL SWITCH BLOCK (SS-2980, PW-2980),

DC-098 (DC IN)

SCHEMATIC DIAGRAM ····························4-21

•FP-140, FP-141, FP-228 FLEXIBLE,

DH-037 (TAPE TOP/END SENSOR, MODE)

SCHEMATIC DIAGRAM ····························4-23

Shematic diagram of the CD-406 board, DI-087 board

andVC-308 board are not shown.

Pages from 4-25 to 4-78 are not shown.

4-3. PRINTED WIRING BOARDS

•BT-012 (BLUETOOTH MODULE)

PRINTED WIRING BOARD ·······················4-81

•AM-025 (ANTENNA)

PRINTED WIRING BOARD ·······················4-82

•LD-112 (FOCUS, ZOOM, IRIS, ND FILTER CON-

TROL) PRINTED WIRING BOARD ·······················4-83

•ST-076 (IR LED DRIVE)

PRINTED WIRING BOARD ·······················4-85

•NS-016 (REMOTE COMMANDER RECEIVER)

PRINTED WIRING BOARD ·······················4-85

•JK-234 (JACK BOARD), SW-380 (PANEL REVERSE),

PK-067 (PANEL ANGLE SW)

PRINTED WIRING BOARD ·······················4-87

•PD-166 (RGB DEIVE/TG)

PRINTED WIRING BOARD ·······················4-89

•VF-155 (PITCH/YAW SENSOR, AMP, EVF),

DC-098 (DC IN)

PRINTED WIRING BOARD ·······················4-91

•FP-538 FLEXIBLE BOARD ·····································4-93

•FP-539, FP-541 FLEXIBLE BOARD························4-95

Printed wiring board ofthe

CD-406board,DI-087board

and VC-308 board

are not shown.

Pages from 4-97 to 4-106 are not shown.

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

—5 —

DCR-IP210/IP210E/IP220/IP220E

•CONTROL SWITCH BLOCK (SS-2980, PW-2980),

FP-140, FP-141, FP-228 FLEXIBLE, DH-037

(TAPE TOP/END SENSOR, MODE SWITCH,

DEW SENSOR, MIC)

PRINTED WIRING BOARD ·····················4-107

4-4. WAVEFORMS ····························································4-109

Waveforms of the CD-406 board, DI-087 board and

VC-308 board are not shown.

Pages from 4-110 to 4-111 are not shown.

4-5. MOUNTED PARTS LOCATION ·······························4-112

Mounted parts location of the

CD-406 board, DI-087

board and VC-308 board

is not shown.

Pages from 4-114 to 4-116 are not shown.

5. REPAIR PARTS LIST

5-1. EXPLODED VIEWS ······················································5-1

5-1-1.OVERALL SECTION·····················································5-1

5-1-2.CABINET (F) SECTION ················································5-2

5-1-3.CABINET (UPPER) SECTION, BATTERY HOLDER

SECTION ········································································5-3

5-1-4.VF SECTION ··································································5-4

5-1-5.LENS SECTION ·····························································5-5

5-1-6.CABINET (LOWER) SECTION ····································5-6

5-1-7.CABINET (L) SECTION················································5-7

5-1-8.CABINET (REAR) SECTION-1 ····································5-8

5-1-9.CABINET (REAR) SECTION-2 (LCD UNIT) ··············5-9

5-1-10. OVERALL (MECHANISM DECK-V100) ················5-10

5-1-11. LS CHASSIS BLOCK ASSEMBLY ··························5-11

5-1-12. MACHANISM CHASSIS BLOCK ASSEMBLY ······5-12

5-2. ELECTRICAL PARTS LIST ········································5-13

Parts list of the CD-406 board, DI-087 board

and VC-308 board are not shown.

Pages from 5-18 to 5-30 are not shown.

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

1-1

DCR-IP210/IP210E/IP220/IP220E

SECTION 1

SERVICE NOTE

COVER

1-1. SERVICE NOTE

1. POWER SUPPLY DURING REPAIRS

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so

that the unit cannot operate.

These following two methods are available to prevent this. Take note of which to use during repairs.

Method 1.

Use the AC power adaptor (AC-L20, AC-VF50).

Method 2.

Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ”side.

2. TOTAKE OUT A CASSETTEWHEN NOT EJECT (FORCE EJECT)

1Remove the power supply (Battery or AC power adaptor).

2Refer to 2-3. and 2-4. to remove the cabinet (F) assembly.

3Discharge the flashlight power supply capacitor. (Refer to “3. DISCHARGING OF THE FLASHLIGHT POWER SUPPLY

CAPACITOR”.)

4Refer to 2-5. to remove the EVF cover.

5Refer to 2-6. to remove the upper cabinet assembly and heat sink.

Note: Be careful not to damage the coaxial connector of the Bluetooth harness. (Refer to “5. COAXIAL CONNECTOR OF THE BLUETOOTH

HARNESS”.)

6Refer to 2-12. to remove the lens block, battery holder and EVF block.

7Disconnect CN453 (31P, 0.3mm) of VC-308 board.

8Open the cassette lid.

9Supply +4.5V from the regulated power supply between pins 3, 4and pins 1, 2of the flexible board which disconnected from

CN453, and unload the cassette. (Be careful not to short-circuit.)

VC-308

Regulated power supply

Enlargement

CN453

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

1-2

DCR-IP210/IP210E/IP220/IP220E

3. DISCHARGING OFTHE FLASHLIGHT POWER SUPPLY CAPACITOR

The capacitor (ST-076 board C4208) of the flash unit is charged up to the maximum 300V potential. There is a danger of electric shock by

this high voltage when the ST-076 board is handled by hand. The electric shock is caused by the charged voltage which is kept without

discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.

3-1. PREPARINGTHE SHORT JIG

To preparing the short jig. a small clip is attached to each end of a resistor of 1kÉ/1W (1-215-869-11). Wrap insulating tape fully around the

reads of the resistor to prevent electric shock.

3-2. DISCHARGINGTHE CAPACITOR

1Remove the power supply (Battery or AC power adaptor).

2Refer to 2-3. and 2-4. to remove the cabinet (F) assembly.

3Short-circuit between TP4201 of the ST-076 board and the LND421 (GND) with the short

jig about 10 seconds.

4. HOWTO OPENTHE FLASH WHENTHE FLASH DOESN’T OPEN

1Remove the power supply (Battery or AC power adaptor).

2Refer to 2-2. to remove the front cap assembly.

3Press the Stopper in the direction of the arrow using a rod.

1 k

Ω

/1 W

Wrap insulating tape

Short jig

Ω

/1W

resister

ST-076 board

LND421

C4208

TR4201

Bluetooth harness

Connector of the

Bluetooth harness

5. COAXIAL CONNECTOR OF THE BLUETOOTH HARNESS (DCR-IP220/IP220E model)

When the coaxial connector of the Bluetooth harness isn’t pulled out vertically toward the board, the connector may be damaged. So, when

disconnecting the connector, be sure to take the connector of the Bluetooth harness, and pull iPress the Stopper in the direction of the arrow

using a rod/t out vertically toward the board.

Stoppe

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

1-3

DCR-IP210/IP210E/IP220/IP220E

6. NOTES ON HANDLING THE LASER DIODE

[LASER UNIT (D5104)]

The laser diode may suffer electrostatic breakdown because of the

potential difference generated by the charged electrostatic load, etc.

on clothing and the human body.

During repair, pay attention to electrostatic breakdown and also use

the procedure in the printed matter which is included in the repair

parts.

The flexible board is easily damaged and should be handled with

care.

6-1. Soldering Conditions of Laser Unit (D5104)

Temperature of Less than 350 °C

the Soldering Iron

Time to Solder 3 seconds

Interval to Solder Next terminal is soldered after

waiting for 1 second

Note: Adjustment is needed when laser unit (D5104) is replaced.

Refer to “18. AF Laser Output Adjustment”and “19. AF Laser

Axis Check”of SERVICE MANUAL, ADJ (992999551.pdf).

Laser Unit

(D5104)

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

1-4

DCR-IP210/IP210E/IP220/IP220E

1-2. SELF-DIAGNOSIS FUNCTION

1. SELF-DIAGNOSIS FUNCTION

When problems occur while the unit is operating, the self-diagnosis

function starts working, and displays on the viewfinder, or LCD

screen what to do. This function consists of two display; self-

diagnosis display and service mode display.

Detailsof theself-diagnosisfunctions areprovidedin the Instruction

manual.

2. SELF-DIAGNOSIS DISPLAY

When problems occur while the unit is operating, the counter of the

viewfinder orLCDscreenconsists of analphabet and 4-digitnumber,

which blinks at 3.2Hz. This 5-character display indicates the

“repairedby:”,“block”inwhich theproblemoccurred, and“detailed

code”of the problem.

3. SERVICE MODE DISPLAY

The service mode display shows the last self-diagnosis code shown in past.

3-1. Display Method

While pressing the “BACK LIGHT”key, set the switch from OFF to ON, and continue pressing the “BACK LIGHT”key for 5 seconds

continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-chracter self-diagnosis code.

3-2. Backup No.

The backup No. in the [ ] indicates the order in which the problem occurred. (If the Number of problems which occurred is less than 6, only

the number of problems which occurred will be shown.)

[1] : Occurred first time [4] : Occurred fourth time

[2] : Occurred second time [5] : Occurred fifth time

[3] : Occurred third time [6] : Occurred last time

Note: Switching of destination can’t be done.

3-3. End of Display

Turning OFF the power supply will end the service mode display.

Note: The self-diagnosis display data will be kept even if the lithium battery (BT4101 of the control switch block (PW-2980)) is removed.

1 1

3 1C

Repaired by:

Refer to page 1-5.

Self-diagnosis Code Table.

Indicates the appropriate

step to be taken.

E.g.

31 ....Reload the tape.

32 ....Turn on power again.

Block Detailed Code

Blinks at 3.2Hz

C : Corrected by customer

H : Corrected by dealer

E : Corrected by service

engineer

Viewfinder or LCD screen

C : 3 1 : 1 1

Order of previous errors

Backup No. Self-diagnosis Codes

C : 3 1 : 1 1

[3]

Lights up

Viewfinder or LCD screen

[3] C : 3 1 : 1 1

WWW.FREESERVICEMANUALS.INFO

12/2

WWW.NOSTATECH.NL

Worlf of free manuals

1-5E

DCR-IP210/IP210E/IP220/IP220E

4. SELF-DIAGNOSIS CODETABLE

Block

Function

Detailed

Code

Symptom/State

Non-standard battery is used.

Condensation.

Video head is dirty.

LOAD direction. Loading does not

complete within specified time

UNLOAD direction. Loading does not

complete within specified time

T reel side tape slacking when unloading

Winding S reel fault when unloading.

T reel fault.

S reel fault.

FG fault during capstan operations.

Capstan reverse rotation.

FG fault when starting drum.

PG fault

when starting drum.

FG fault during normal drum operations.

PG fault during normal drum operations.

LOAD direction loading motor time-

out.

UNLOAD direction loading motor

time-out.

T reel side tape slacking when

unloading.

Winding S reel fault when unloading.

T reel fault.

S reel fault.

FG fault during capstan operations

Captan reverse operations

FG fault when starting drum

PG fault when starting drum

FG fault during normal drum

operations

PG fault during normal drum

operations

Difficult to adjust focus

(Cannot initialize focus.)

Zoom operations fault

(Cannot initialize zoom lens.)

Self-diagnosis Code

Repaired by:

Correction

Use the info LITHIUM battery.

Remove the cassette, and insert it again after one hour.

Clean with the optional cleaning cassette.

Load the tape again, and perform operations from the beginning.

Remove the battery or power cable, connect, and perform