—2 —
SAFETY-RELATED COMPONENTWARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1. Check theareaof your repair for unsolderedorpoorly-soldered
connections. Checktheentire board surfaceforsolder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, showobvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
DCR-PC8E
TABLE OF CONTENTS
4. PRINTEDWIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS ··········································4-19
• VC-265D (A/D CONVERTER)(1/16)
SCHEMATIC DIAGRAM ····························4-19
• VC-265D (CAMERA SIGNAL PROCESS)(2/16)
SCHEMATIC DIAGRAM ····························4-21
• VC-265D (LENS DRIVER)(3/16)
SCHEMATIC DIAGRAM ····························4-23
• VC-265D (DV SIGNAL PROCESS)(4/16)
SCHEMATIC DIAGRAM ····························4-25
• VC-265D (DV INTERFACE)(5/16)
SCHEMATIC DIAGRAM ····························4-27
• VC-265D (HI CONTROL)(6/16)
SCHEMATIC DIAGRAM ····························4-29
• VC-265D (LINE IN/OUT)(7/16)
SCHEMATIC DIAGRAM ····························4-31
• VC-265D (LINE A/D)(8/16)
SCHEMATIC DIAGRAM ····························4-33
• VC-265D (REC/PB AMP)(9/16)
SCHEMATIC DIAGRAM ····························4-35
• VC-265D (MECHA CONTROL)(10/16)
SCHEMATIC DIAGRAM ····························4-37
• VC-265D (DRUM/CAPSTAN MOTOR)(11/16)
SCHEMATIC DIAGRAM ····························4-39
• VC-265D (AUDIO IN/OUT)(12/16)
SCHEMATIC DIAGRAM ····························4-41
• VC-265D (EVF RGB DRIVER)(13/16)
SCHEMATIC DIAGRAM ····························4-43
• VC-265D (DC/DC CONVERTER)(14/16)
SCHEMATIC DIAGRAM ····························4-45
• VC-265D (DC/DC CONVERTER)(15/16)
SCHEMATIC DIAGRAM ····························4-47
• VC-265D (CONNECTOR)(16/16)
SCHEMATIC DIAGRAM ····························4-49
4-3. PRINTED WIRING BOARDS
• VC-265D (A/D CONVERTER, CAMERA SIGNAL
PROCESS, LENS DRIVE, MS INTERFACE, DV
SIGNAL PROCESS, HI CONTROL, LINE IN/OUT,
REC/PB AMP, MECHA CONTROL, SERVO, AUDIO,
DC/DC CONVERTER)
PRINTED WIRING BOARD ·······················4-65
4-4. WAVEFORMS ······························································4-71
4-5. MOUNTED PARTS LOCATION ·································4-75
6. REPAIR PARTS LIST
6-2. ELECTRICAL PARTS LIST ········································6-12