Sony Handycam DCR-TRV940 Guide

SECTION 6
ADJUSTMENTS
DCR-TRV940/TRV940E/TRV950/TRV950E
RMT-811
ADJ
Revision History
Revision History
Ver 1.0 2002. 05
Link
Link
Adjusting items when replacing main parts and boards
Before starting adjustments
Adjusting items when replacing main parts and boards
Before starting adjustments
LCD SYSTEM ADJUSTMENTS
ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
INITIALIZATION OF 8, A, B, C, D, E, F, 1B, 1E, 1F PAGE DATA
PREPARATIONS BEFORE ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
INITIALIZATION OF 8, A, B, C, D, E, F, 1B, 1E, 1F PAGE DATA
PREPARATIONS BEFORE ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
TAPE PATH ADJUSTMENT
HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE
HOW TO ENTER RECORD MODE WITHOUT CASSETTE
MECHANISM SECTION ADJUSTMENTS
TAPE PATH ADJUSTMENT
HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE
HOW TO ENTER RECORD MODE WITHOUT CASSETTE
MECHANISM SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO AND RF SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO AND RF SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
Sony EMCS Co. 2002E0500-1
©2002.5
Published by DI Customer Center
9-929-978-51
Contents of LEVEL 2 and LEVEL 3 Service Manual
CONTENTS
1. SERVICE NOTE
2. DISASSEMBLY
3. BLOCK DIAGRAMS
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
5. REPAIR PARTS LIST
LEVEL 2
a
a
OVERALL
POWER
CD-389, CK-116, JK-222,
LB-080, MA-410, PD-168,
SE-132 BOARD
FP-100, FP-102, FP-228,
FP-495, FP-497, FP-500,
FP-503, FP-504
FLEXIBLE
EXPLODED VIEWS
ELECTRICAL PARTS
LEVEL 3
✕
✕
✕
DB-014, VC-288 BOARD
✕
a
(DB-014, VC-288 BOARD)

DCR-TRV940/TRV940E/TRV950/TRV950E
— 2 —
TABLE OF CONTENTS
6. ADJUSTMENTS
Before Starting Adjustments ·····················································6-1
1-1. Adjusting Items when Replacing
Main Parts and Boards ····················································6-2
6-1. Camera Section Adjustments···········································6-4
1-1. Preparations before Adjustments (CAMERA Section) ···6-4
1-1-1.List of Service Tools ························································6-4
1-1-2.Preparations ·····································································6-5
1-1-3.Precaution ········································································6-7
1. Setting the Switch····························································6-7
2. Order of Adjustment ························································6-7
3. Subjects ···········································································6-7
4. Preparing the Flash Adjustment Box·······························6-8
1-2. Initialization of 8, A, B, C, D, E, F, 1B, 1E,
1F Page Data ···································································6-9
1-2-1.Initialization ofA, D Page Data ····································6-10
1. Initializing A, D Page Data············································6-10
2. Modification of A, D Page Data ····································6-10
3. A Page Table··································································6-11
4. D Page Table··································································6-11
1-2-2.Initialization of 8, C Page Data ·····································6-12
1. Initializing 8, C Page Data ············································6-12
2. Modification of 8, C Page Data ·····································6-12
3. 8 Page Table···································································6-13
4. C Page Table ··································································6-13
1-2-3.Initialization of E, F, 1E, 1F Page Data ·························6-15
1. Initializing of E, F, 1E, 1F Page Data ····························6-15
2. Modification of E, F, 1E, 1F Page Data·························6-15
3. E Page Table ··································································6-16
4. F Page Table ··································································6-17
5. 1E Page Table ································································6-19
6. 1F Page Table ································································6-20
1-2-4.Initialization of B, 1B Page Data···································6-21
1. Initializing of B, 1B Page Data ·····································6-21
2. Modification of B, 1B Page Data ··································6-21
3. B Page Table ··································································6-21
4. 1B Page Table ································································6-21
5. Initializing of Network Setting Data
(DCR-TRV950/TRV950E) ············································6-22
1-3. Camera System Adjustments ·········································6-23
1. 66MHz/54MHz Origin Oscillation Adjustment
(VC-288 Board)·····························································6-23
2. Hall Adjustment·····························································6-24
3. MR Adjustment ·····························································6-25
4. Flange Back Adjustment
(Using the Minipattern Box) ·········································6-26
5. Flange Back Adjustment
(Using the Flange Back Adjustment Chart
and Subject More than 500 m Away) ····························6-27
6. Flange Back Check························································6-28
7. Picture Frame Setting ····················································6-29
8. AWB Standard Data Input ·············································6-30
9. MAX GAIN Adjustment ···············································6-30
10. F No. & ND Light Quality Standard Data Input ···········6-31
11. LV Standard Data Input ·················································6-31
12. Auto White Balance Adjustment ···································6-32
13. Auto White Balance Check ···········································6-33
14. Color Reproduction Adjustment····································6-34
15. PSD Sensor Gain Adjustment········································6-35
16. Angular Velocity Sensor Sensitivity Adjustment ··········6-37
17. Mechanical Shutter Adjustment ····································6-38
18. Strobe Light Level Adjustment ·····································6-38
19. Strobe White Balance Adjustment·································6-39
20. Hologram AF Output Adjustment ·································6-40
21. Hologram AF Angle Check ···········································6-41
1-4. Color Electronic Viewfinder SystemAdjustments ········6-42
Section Title Page Section Title Page
1. VCO Adjustment (DB-014 Board)································6-42
2. RGB AMP Adjustment (DB-014 Board)·······················6-43
3. Contrast Adjustment (DB-014 Board)···························6-43
4. Back Light Adjustment (DB-014 Board) ······················6-44
5. White Balance Adjustment (DB-014 Board)·················6-44
1-5. LCD System Adjustments ·············································6-45
1. VCO Adjustment (PD-168 Board) ································6-45
2. RGB AMP Adjustment (PD-168 Board) ·······················6-46
3. Contrast Adjustment (PD-168 Board) ···························6-46
4. V-COM LevelAdjustment (PD-168 Board) ··················6-47
5. V-COM Adjustment (PD-168 Board) ····························6-47
6. White Balance Adjustment (PD-168 Board) ·················6-48
6-2. Mechanism Section Adjustments ··································6-49
2-1. How to Enter Recod Mode Without Cassette ················6-49
2-2. How to Enter Playback Mode Without Cassette ···········6-49
2-3. Tape Path Adjustment ····················································6-49
6-3. Video Section Adjustments ···········································6-50
3-1. Preparations before Adjustments ···································6-50
3-1-1.Equipment Required······················································6-50
3-1-2.Precautions on Adjusting ···············································6-51
3-1-3.Adjusting Connectors ····················································6-52
3-1-4.Connecting the Equipment ············································6-52
3-1-5.Alignment Tapes····························································6-53
3-1-6.Input/Output Level and Impedance ·······························6-53
3-2. System Control System Adjustments ····························6-54
1. Initialization of 8, A, B, C, D, E, F, 1B, 1E,
1F Page Data ·································································6-54
2. Touch Panel Adjustment ················································6-54
3. Node Unique ID No. Input ············································6-55
3-1. Input of Company ID ····················································6-55
3-2. Input of Serial No. ·························································6-55
3-3. Servo and RF System Adjustments ······························6-57
1. CAP FG Duty Adjustment (VC-288 Board) ·················6-57
2. PLL f0& LPF f0Pre-Adjustment (VC-288 Board) ·······6-57
3. Switching Position Adjustment (VC-288 Board) ··········6-58
4. AGC Center Level andAPC & AEQAdjustment ·········6-58
4-1. Preparations before Adjustments ···································6-58
4-2. AGC Center LevelAdjustment (VC-288 Board) ··········6-59
4-3. APC & AEQ Adjustment (VC-288 Board) ··················6-59
5. PLL f0& LPF f0 Final Adjustment (VC-288 Board) ·····6-60
3-4. Video System Adjustments············································6-61
1. Chroma BPF f0Adjustment (DB-014 Board)················6-61
2. S VIDEO OUTY LevelAdjustment
(DB-014 Board)·····························································6-62
3. S VIDEO OUT Chroma LevelAdjustment
(DB-014 Board)·····························································6-62
4. VIDEO OUT Level Check (DB-014 Board) ·················6-63
3-5. Audio System Adjustments ···········································6-64
1. Playback Level Check ···················································6-64
2. Overall Level Characteristics Check ·····························6-64
3. Overall Distortion Check···············································6-64
4. Overall Noise Level Check············································6-65
5. Overall Separation Check··············································6-65
6-4. Service Mode·································································6-66
4-1. Adjusting Remote Commander ·····································6-66
1. Using the Adjustment Remote Commander ··················6-66
2. Precautions Upon Using the Adjustment
Remote Commander······················································6-66
4-2. Data Process ··································································6-67
4-3. Service Mode·································································6-68
1. Setting the Test Mode ····················································6-68
2. Emergence Memory Address ········································6-68
2-1. C Page Emergence Memory Address ····························6-68
2-2. EMG Code (Emergency Code) ·····································6-69
2-3. MSW Code ····································································6-70
3. Bit Value Discrimination ···············································6-71

DCR-TRV940/TRV940E/TRV950/TRV950E
— 3 —
*The color reproduction frame is shown on page 6-75
Section Title Page
4. Jack Check (1) ·······························································6-71
5. Jack Check (2) ·······························································6-71
6. Switch Check·································································6-72
7. LED, LCD (Display Window) Check ···························6-72
8. Record of Use Check (1) ···············································6-73
9. Record of Use Check (2) ···············································6-73
10. Record of Self-diagnosis Check ····································6-74

DCR-TRV940/TRV940E/TRV950/TRV950E
6-1
SECTION 6
ADJUSTMENTS
1. Before starting adjustments
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
Remove the EEPROM and install it.
(Former board) (New board)
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed
EEPROM to the replaced board.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)
(Machine before starting repair) (Machine after a board is replaced) PC PC
Save the EVR data
to a personal computer. Download the saved
data to a machine.
(Machine to be repaired) (Machine to be repaired)
(The same model of the same destination)
Save the data.
Download the data.
PC
COVER
COVER

DCR-TRV940/TRV940E/TRV950/TRV950E
6-2
COVER
COVER
1-1. Adjusting items when replacing main parts and boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by zin the following table.
Table 6-1-1 (1)
Note 1: When replacing the drum assy or mechanism deck, reset the drum rotation counted time.
(Refer to “Record of Use Check”of “6-4. SERVICE MODE”)
Replaced part
Block replacement Mounted part replacement
Adjustment Section Adjustment
(LCD panel (EVF)) (LCD panel (LCD) (Fluorescent tube) (Touch panel) (Drum assembly) (Note 1) (Capstan motor) (Prism block (CCD imager)) (S/H) (Timing generator) (A/D converter) (EVR) (DV signal process) (EQ, A/D CONV., PLL) (REC/PB AMP) (Video IN/OUT) (LCD driver (EVF)) (Timing generator (EVF)) (Back light (EVF)) (PITCH, YAW sensor) (LCD driver (LCD)) (Timing generator (LCD))
Lens device FLASH unit LASER unit D501 Mechanism deck (Note 1) EVF block LCD903 LCD block LCD901 LCD block ND901 LCD block TA901 Mechanism deck M901 Mechanism deck M902 CD-389 board IC100, 101, 105 CD-389 board IC102, 103, 104 VC-288 board IC1202, X1201 VC-288 board IC1203, 1204, 1205 VC-288 board IC1801 VC-288 board IC2101 VC-288 board IC1901 VC-288 board IC1902 DB-014 board IC7001 DB-014 board IC4201 DB-014 board IC4202 LB-080 board D6102 SE-132 board SE4001, 4002 PD-168 board IC5701 PD-168 board IC5702
Initialization of Initialization of A, D page data
8, A, B, C, D, E, F, Initialization of 8, C page data
1B, 1E, 1F Initialization of E, F, 1E, 1F page data
page data Initialization of B, 1B page data
Camera 66MHz/54MHz origin oscillation adj. zz
HALL adj. zz
MR adj. zz
Flange back adj. zz
AWB standard data input zz z
MAX GAIN adj. zz z
F No. & ND light quality standard data input z
LV standard data input zz z
Auto white balance adj. zz z
Color reproduction adj. zz z
PSD sensor gain adj. z z
Angular velocity sensor sensitivity adj. z z
Mechanical shutter adj. z
Strobe light level adj. z
Strobe white balance adj. zzzz
Hologram AF output adj. z
Hologram AF angle check z
Color EVF VCO adj. zz
RGB AMP adj. z
Contrast adj. zz
Back light adj. zz
White balance adj. zzz
LCD VCO adj. zz
RGB AMP adj. z
Contrast adj. zz
V-COM level adj. z
V-COM adj. zz
White balance adj. zz z
System control Touch panel adj. z
Node uniqe ID No. input
Servo, RF CAP FG duty adj. zz
Switching position adj. zz
AGC center level adj. zz zz
APC & AEQ adj. zz zz
PLL f 0 & LPF f 0 adj. zz zz
Video Chroma BPF f 0 adj. z
S VIDEO OUT Y level adj. z
S VIDEO OUT chroma level adj. z
Mechanism Tape path adj. zzz

DCR-TRV940/TRV940E/TRV950/TRV950E
6-3
•Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by zin the following table.
Table 6-1-1 (2)
Replaced part
Adjustment Section Adjustment
(COMPLETE) (Note 2, 3) (COMPLETE) (COMPLETE) (COMPLETE) (COMPLETE) (COMPLETE) (COMPLETE) (Note 4) (EEP ROM) (EEP ROM)
BT-003 board CD-389 board SE-132 board DB-014 board LB-080 board PD-168 board VC-288 board VC-288 board IC2502 VC-288 board IC2901 Supporting Radar W
Initialization of Initialization of A, D page data zz
8, A, B, C, D, E, F, Initialization of 8, C page data zz
1B, 1E, 1F Initialization of E, F, 1E, 1F page data zz
page data Initialization of B, 1B page data zz
Camera 66MHz/54MHz origin oscillation adj. zz
HALL adj. zz z
MR adj. zz z
Flange back adj. zz z
AWB standard data input zzzz
MAX GAIN adj. zzzz
F No. & ND light quality standard data input zz z
LV standard data input zzzz
Auto white balance adj. zzzz
Color reproduction adj. zzz
PSD sensor gain adj. zzz
Angular velocity sensor sensitivity adj. zzz
Mechanical shutter adj. zz z
Strobe light level adj. zz z
Strobe white balance adj. zzzz
Hologram AF output adj. zz z
Hologram AF angle check z
Color EVF VCO adj. zzz
RGB AMP adj. zzz
Contrast adj. zzz
Back light adj. zz zz
White balance adj. zz zz
LCD VCO adj. zzz
RGB AMP adj. zzz
Contrast adj. zzz
V-COM level adj. zzz
V-COM adj. zzz
White balance adj. zzz
System control Touch panel adj. zz
Node uniqe ID No. input zz
Servo, RF CAP FG duty adj. zz z
Switching position adj. zz z
AGC center level adj. zz z
APC & AEQ adj. zz z
PLL f0& LPF f0adj. zz z
Video Chroma BPF f0adj. zzz
S VIDEO OUT Y level adj. zzz
S VIDEO OUT chroma level adj. zzz
Mechanism Tape path adj.
Note 2: DCR-TRV950/TRV950E only
Note 3: After BT-003 board is replaced,
check the “Info.”is correctly dis-
played with the following proce-
dure.
1) Turn the power switch to
“MEMORY/NETWORK”.
2) Press the “NETWORK”but-
ton.
3) Select/Execute the “Setup”at
the network menu.
4) Select/Execute the “Bluetooth”
at the network menu.
5) Select/Execute the “Info.”at
the network menu.
6) Check that the following infor-
mation is displayed.
Name SONY DCR-TRV950
(or DCR-TRV950E)
Address 08 : 00 : 46 : XX : XX : XX
Note 4: When VC-288 board is replaced,
before and after the replacement,
execute “Initializing of Network
Setting Data”and initialize network
personal information (mail address,
bookmark).
(DCR-TRV950/TRV950E only)
(Refer to “1-2-4. Initialization of B,
1B Page Data”)

DCR-TRV940/TRV940E/TRV950/TRV950E
6-4
COVER
COVER
J-1 J-2
J-6
J-3
J-7 J-8
J-4 J-5
Fig. 6-1-1
J-9 J-10
J-11
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
J-12
J-13
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander (RM-95 upgraded).
(Note)
Siemens star chart
Clear chart for pattern box
CPC-8 jig
Extension cable (60 P, 0.5 mm)
Mini pattern box
Camera table
CPC-jig for LCD panel
Background paper
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-388-A
J-6082-466-A
J-6082-353-B
J-6082-384-A
J-6082-529-A
J-2501-130-A
Usage
Auto white balance adjustment/check
White balance adjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For adjusting the video section
For adjusting the color viewfinder
For extension between the CD-389 board (CN100) and
VC-288 board (CN1201)
For adjusting the flange back
For adjusting the flange back
For adjusting the LCD system
6-1. CAMERA SECTION ADJUSTMENTS
1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION)
1-1-1. List of ServiceTools
•Oscilloscope •Color monitor •Vectorscope
•Regulated power supply •Digital voltmeter •Frequency counter
Note 1: If the micro processor IC in the adjustment remote com-
mander is not the new micro processor (UPD7503G-
C56-12), the pages cannot be switched. In this case, re-
place with the new micro processor (8-759-148-35).
J-12 J-13

DCR-TRV940/TRV940E/TRV950/TRV950E
6-5
Fig. 6-1-2
1-1-2. Preparations
Note 1: For details of how remove the cabinet and boards, refer
to “2. DISASSEMBLY”.
Note 2: When performing only the adjustments, the lens block
and boards need not be disassembled.
Note 3: Before perform the adjustment, check that the data of
page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set data “00”.
1) Connect the equipment for adjustments according to
Fig. 6-1-3.
Note 4: As removing the cabinet (R) (removing the CK-116 board
CN5203) means removing the lithium 3V power supply
(BT5201), data such as date, time, user-set menus will
be lost. After completing adjustments, reset these data.
If the NS-014 board has been removed, the self-diagno-
sis data, data on history of use (total drum rotation time,
etc. ) will not be lost. (Refer to “SELF-DIAGNOSIS
FUNCTION”for the self-diagnosis data, and to “6-4.
Service Mode”for the data on the history use)
Note 5: Setting the “Forced Camera Power ON”Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press
the PAUSE button of the adjustment remote com-
mander.
The above procedure will enable the camera power
to be turned on with the power switch (PS-1870 block)
removed. After completing adjustments, be sure to
exit the “Forced Camera Power ON Mode”.
Note 6: Exiting the “Forced Camera Power ON”Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press
the PAUSE button of the adjustment remote com-
mander.
3) Select page: 0, address: 01, and set data: 00.
Pattern box
Front of the lens
1m

DCR-TRV940/TRV940E/TRV950/TRV950E
6-6
Fig. 6-1-3
Must be connected when
performing the EVF system
adjustment.
Must be connected when
performing the LCD system
adjustment.
Must be connected when
performing the video or
EVF system adjustment.
Must be connected to FLASH unit
when performing the strobe
adjustment.
Must be connected to
SE-132 board when performing
the steady shot check
VC-288 board
FP-498
flexible
FP-499
flexible
CK-116 board
JK-222 board
MA-410
board
CN1006
CN1901 CN1007
CN1024
CN1008
CN5205
CN5204
CN5203
CN5206
CN5201CN5202
CN1009
CN1023
CN1201
CN1022
CN1005
CN1021
CN1003
CN1002
DB-014 board
CD-389 board
LENS BLOCK
EVF BLOCK
FRONT PANEL BLOCK
Extension cable (60P, 0.5mm) (J-6082-466-A)
CABINET (R)
CN7211 CN1010
CN7205
CN7207 CN7206
CN1501
CN1004
CN7200
CN7202
CN100
CN7201
CN7204
CN1001
CPC-jig for LCD panel
(J-6082-529-A)
CPC-8 jig
(J-6082-388-A)
61
Must be connected
Must be connected
Connect to Mechanism deck
Must be
connected
CN5904
CN5906
AC power adaptor (8.4 Vdc)
AC-L10, AC-VQ800 etc.
Vectorscope
Color monitor
Video (Yellow)
Audio/Video
jack
HEAD PHONE
jack
S Video
jack
LANC jack
USB jack
DV jack
Audio L
(White)
Audio R
(Red)
Terminated at 75 Ω
Adjustment remote
commander
DC IN jack

DCR-TRV940/TRV940E/TRV950/TRV950E
6-7
H
A=B
C=D
AB B
CD
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
BA
Difference in level
Yellow
Cyan
Green
White
Magenta
Red
Blue
Yellow
Cyan
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame)
Fig. a
(VIDEO terminal of A/V jack
output waveform)
Fig. b (monitor TV picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig.a and
the monitor TV display shown in Fig.b.
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (PS-1870 block) ..........................CAMERA
2. FOCUS (FP-504 flexible) ............................................ MAN
3. BACK LIGHT (CK-116 board) ..................................... OFF
4. SPOT LIGHT (CK-116 board) ...................................... OFF
5. ZEBRA (CK-116 board) ................................................ OFF
6. PROGRAM AE (KP-1870 block) .................................. OFF
7. SHUTTER SPEED (KP-1870 block) ......................... AUTO
8. WHITE BAL (KP-1870 block) ...................................... OFF
9. EXPOSURE (KP-1870 block) .................................... AUTO
10. P EFFECT (MENU setting) ........................................... OFF
11. FLASH LVL (MENU setting).............................. NORMAL
12. D ZOOM (MENU setting) ............................................. OFF
13. STEADY SHOT (MENU setting) .................................. OFF
14. DEMO MODE (MENU setting) .................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig. 6-1-4
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clearchart in its place. (Do not perform zoom operations during
this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm ×841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
Fig. 6-1-5
Black
White 841 mm
1189 mm