Sony Handycam HDR-CX330 User manual

SERVICE MANUAL
SERVICE NOTE (Check the following note before the service.)
Revision History
Published by Sony Techno Create Corporation
Sony Corporation
LEVEL 2
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
983477432.pdf
Digital HD Video Camera Recorder
The components identified by mark
0or dotted line with mark 0are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0sont critiques pour la
sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
9-834-774-32
Ver. Date History Contents S.M. Rev.
issued
1.0 2014.01 Official Release — —
1.1 2014.03 Revised-1
(A1 13-209)
• Addition of HDR-PJ350.
Page 2,1-1,2-1,2-5,2-7
Yes
2014C08-1
© 2014.03
1-1. POWER SUPPLY DURING REPAIRS
1-2. PRECAUTION ON REPLACING THE VC-1025 BOARD
1-3. CHECKING THE Wi-Fi FUNCTION
1-4. SELF-DIAGNOSIS FUNCTION
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
1-6. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Ver. 1.1 2014.03 US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Hong Kong Model
Chinese Model
Korea Model
Brazilian Model
Tourist Model
HDR-CX330/CX330E/PJ330E/PJ340/
PJ340E/PJ350/PJ350E
Photo: HDR-CX330/Black
Revised-1
Replace the previously issued
SERVICE MANUAL 9-834-774-31
with this Manual.

– 2 –
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
SPECIFICATIONS
System
Signal format:
NTSC color, EIA standards (HDR-CX330/
PJ340/PJ350)
PAL color, CCIR standards (HDR-CX330E/
PJ330E/PJ340E/PJ350E)
HD TV
Movie recording format:
AVCHD (AVCHD format Ver.2.0
compatible):
Video: MPEG-4 AVC/H.264
Audio: Dolby Digital 2ch
Dolby Digital Stereo Creator*1
MP4:
Video: MPEG-4 AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
*1 Manufactured under license from Dolby
Laboratories.
Photo file format:
DCF Ver.2.0 Compatible
Exif Ver.2.3 Compatible
MPF Baseline Compatible
Recording media (Movie/Photo):
Internal memory
HDR-PJ350/PJ350E: 32 GB
HDR-PJ340/PJ340E: 16 GB
Memory Stick Micro (Mark2)
media
microSD card (Class 4 or faster)
The capacity that a user can use
(Approx.)
HDR-PJ350/PJ350E: 31.1 GB*2
HDR-PJ340/PJ340E: 15.5 GB*2
*2 1 GB equals 1 billion bytes, a portion of
which is used for system management and/
or application files. Only preinstalled dem-
onstration movie may be deleted.
Image device:
3.1 mm (1/5.8 type) CMOS Sensor
Recording pixels (photo, 16:9):
Max. 9.2 mega pixels
(4 032 × 2 272)*3
Gross: Approx. 2 510 000 pixels
Effective (movie, 16:9)*4:
Approx. 2 290 000 pixels
Effective (photo, 16:9):
Approx. 2 290 000 pixels
Effective (photo, 4:3):
Approx. 1 710 000 pixels
Lens:
G Lens
30× (Optical)*4, 60× (Clear Image
Zoom, while recording movies)*5,
350× (Digital)
Filter diameter: 37 mm (1 1/2 in.)
F1.8 - F4.0
Focal length:
f= 1.9 mm - 57.0 mm (3/32 in. - 2 1/4 in.)
When converted to a 35 mm still camera
For movies*4: 26.8 mm - 804.0 mm
(1 1/16 in. - 31 3/4 in.) (16:9)
For photos: 26.8 mm - 804.0 mm
(1 1/16 in.- 31 3/4 in.) (16:9)
Color temperature: [Auto], [One Push],
[Indoor], [Outdoor]
Minimum illumination:
6 lx (lux) (in default setting,
shutter speed 1/30 second (HDR-CX330/
PJ340/PJ350) or
1/25 second (HDR-CX330E/
PJ330E/PJ340E/PJ350E))
3 lx (lux) ([Low Lux] is set to [On],
shutter speed 1/30 second (HDR-CX330/
PJ340/PJ350) or
1/25 second (HDR-CX330E/
PJ330E/PJ340E/PJ350E))
*3 The unique image processing system of
Sony’s BIONZ-X allows still image resolu-
tion equivalent to the sizes described.
*4 [ SteadyShot] is set to
[Standard] or [Off].
*5 [ SteadyShot] is set to [Active].
Input/Output connectors
HDMI OUT jack: HDMI micro connector
PROJECTOR IN jack (HDR-PJ330E/
PJ340/PJ340E/PJ350/PJ350E):
HDMI micro connector
USB jack: Type A (Built-in USB)
Multi/Micro USB Terminal*
* Supports Micro USB compatible devices.
USB connection is only for output
(HDR-CX330E/PJ330E/PJ340E/PJ350E).
LCD monitor
Picture: 6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels:
230 400 (960 × 240)
Projector (HDR-PJ330E/PJ340/
PJ340E/PJ350/PJ350E)
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Throw Distance: 0.5 m (1.6 feet) or over
Contrast ratio: 1 500:1
Resolution (output): 640 × 360
Continuous projection time (when
using the supplied battery pack):
Approx. 1 h. 45 min.
Wireless LAN
Supported standard:
IEEE 802.11 b/g/n
Frequency: 2.4 GHz
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Protected Setup)/manual
Access method: Infrastructure Mode
NFC: NFC Forum Type 3 Tag compliant
General
Power requirements: DC 6.8 V/7.2 V
(battery pack), DC 5 V 1 500 mA
(AC Adaptor), DC 8.4 V (DC IN jack)
USB Charging: DC 5 V 1 500 mA
Average power consumption:
During camera recording using LCD
monitor at normal brightness: 2.1 W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Dimensions (approx.):
HDR-CX330/CX330E:
57.0 mm × 59.5 mm × 119.0 mm
(2 1/4 in. × 2 3/8 in. × 4 3/4 in.)
(w/h/d) including the projecting parts
57.0 mm × 59.5 mm × 128.5 mm
(2 1/4 in. × 2 3/8 in. × 5 1/8 in.) (w/h/d)
including the supplied
rechargeable battery pack attached
HDR-PJ330E/PJ340/PJ340E/PJ350/PJ350E:
61.0 mm × 59.5 mm × 119.0 mm
(2 1/2 in. × 2 3/8 in. × 4 3/4 in.)
(w/h/d including the projecting parts
61.0 mm × 59.5 mm × 128.5 mm
(2 1/2 in.× 2 3/8 in.× 5 1/8 in.) (w/h/d)
including the supplied rechargeable battery
pack attached
Mass (approx.)
HDR-CX330/CX330E:
190 g (6.7 oz) main unit only
245 g (8.6 oz) including the
supplied rechargeable battery pack
HDR-PJ330E/PJ340/PJ340E/PJ350/PJ350E:
215 g (7.6 oz) main unit only
270 g (9.5 oz) including the
supplied rechargeable battery pack
AC Adaptor AC-UUD11
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 200 mA
Power consumption: 11 W
Output voltage: DC 5.0 V, 1 500 mA
Operating temperature: 0 °C to 50 °C
(32 °F to 122 °F)
Storage temperature: –20 °C to
+60 °C (–4 °F to +140 °F)
Rechargeable battery pack NP-FV50
Maximum output voltage: DC 8.4 V
Output voltage: DC 6.8 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.1 A
Capacity
Typical: 7.0 Wh (1 030 mAh)
Minimum: 6.6 Wh (980 mAh)
Type: Li-ion
Design and specifications of your
camcorder and accessories are
subject to change without notice.
Model information table
Model CX330 CX330E PJ330E PJ340 PJ340E PJ350 PJ350E
Destination US, CND, E,
BR
AEP, UK, NE AEP, UK, NE US, CND, E,
KR, BR
E, HK, JE US CH
COLOR system NTSC PAL PAL NTSC PAL NTSC PAL
Internal recording
media
– – – Internal memory
16 GB
Internal memory
16 GB
Internal memory
32 GB
Internal memory
32 GB
LENS LSV-1610A LSV-1610A LSV-1610A LSV-1610A LSV-1610A LSV-1610A LSV-1610A
Projector – – 33333
G
PS –––––––
E
VF –––––––
Wi-Fi 3333333
NFC 3333333
Multi interface shoe –––––––
Charging capacitor
(for flash)
–––––––
MODEL GROUP
Projector Model: PJ330E/PJ340/PJ340E/PJ350/PJ350E
Non Projector Model: CX330/CX330E
• Abbreviation
BR: Brazilian model
CH: Chinese model
CND: Canadian model
HK: Hong Kong model
JE: Tourist model
KR: Korea model
NE: North European model
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.03

– 3 –
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are pinched or
contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。

1-1
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 Vdc), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-1025 BOARD
Note the following when replacing the board.
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed. In this case, execute the [DESTINATION DATA WRITE]
then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB Serial Save
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
Data for projector (Projector Model)
Before replacing the board with a spare board, acquire the following data from the current board.
• Fixed value (that shows irradiation performance of the projector).
• Serial number of the projector unit.
To acquire the data, start Adjust Manual from Adjust Station and select [Projector Data Reference] on the [DATA] tab.
Update of MAC Address
When replacing a VC board, the IC’s unique number (MAC address) must be reloaded.
After the board has been replaced with a board for service, perform the following procedure to reload the IC’s unique number (MAC address).
Note: Perform this operations after all work has been done.
1. Download the latest-version Adjust Manual.
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN Setting (MAC address)” on the ADJUST tab.
If “Wireless LAN Setting (MAC address)” is not executed and the backup data before replacement is restored, the MAC address in the Wi-Fi module
does not match the MAC address in the flash memory, causing an error during Wi-Fi transfer.
Note: The “LOAD AND WRITE” function in “ADJUSTMENT DATA BACKUP” on the DATA tab in the Adjust manual overwrites all data of the unit. Therefore,
the MAC address updated during the above procedure is also overwritten.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
About unit with Internal Memory Model (PJ340/PJ340E/PJ350/PJ350E)
After the board replacement, execute the procedure below first.
1. Execute the [DESTINATION DATA WRITE] of ADJUST tab in the Adjust Manual.
2. Execute the script files below. (Refer to the flowchart in Fig. 1)
• 14DdmMmcReadTestMINI_v6.vbe
• 14DdmMmcMakePartition_v6.vbe
Unless these script files are executed, the following symptoms may appear.
Make sure execute the above script files.
• The internal memory is not recognized as a media.
• The management file saved in the internal memory model cannot be repaired.
• The internal memory cannot be formatted.
START
END
Reactive the camcorder automatically
Disconnect the USB cable,
and turn off the power switch.
Select the "USB CONNECT" to establish
the connection
Execute
the "14DdmMmcReadTestMINI_v6.vbe"
(several second later)
Wait until "SetOverallReadMINI OK" display
(10 seconds later)
Reactive the camcorder automatically
Execute
the "14DdmMMCMakePartition_v6.vbe"
(several second later)
Wait until "MakePartition OK" display
During the power is turning-on,
pull-out the AC-adapter.
Then connect the AC-adapter Again
(It's running with blue color monitor.)
Connect to the PC with a USB cable,
and turn on the power switch.
*by SEUS driver
Fig.1
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.03

1-2
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-3. CHECKING THE Wi-Fi FUNCTION
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi interface
1. Turn on the power of the unit.
2. Perform the following operations.
[MENU]→[Camera/Mic]→[ Shooting Assist]→[Ctrl with Smartphone]
3. When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.
Ctrl with Smartphone
Operate smartphone to connect to
this device via Wi-Fi.
SSID DIRECT-XXXX:HDR-XXXX
Password XXXXXXXX
Device Name HDR-XXXX
Wi-Fi
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and double-click the “current connection” from the icon
displayed on the notice field, make sure that the unit is displayed in the Wireless internet access column.
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
00
32C
Repaired by:
Refer to “1-4-3. Self-diagnosis Code Tabl e”.
Indicates the appropriate
step to be taken.
E.g.
13 ....
32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2 Hz
C : Corrected by customer
E : Corrected by service
engineer
Format the “memory card”.
Viewfinder or LCD screen
1-4-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
C 0 4 0 0 Non-standard battery is used. Use the InfoLITHIUM battery.
C 0 6 0 0 The battery pack temperature is high. Change the battery pack or place it in a cool place.
C1 3 0 1
Memory card is unformatted.
Memory card is broken.
Format the memory card.
Insert a new memory card.
C 1 3 0 2 Access error Remove the power source. Reconnect it again and operate your cam-
corder again.
C 1 3 0 3 Access error (External media) Turn power off and turn power on again.
C 1 3 0 4 Drive fault (External media) Turn power off and turn power on again.
C
E
32
61
60
00
Difficult to adjust focus
(Cannot initialize focus)
Retry turn the power on by the power switch. If it does not recover, check
the focus drive signal of lens block (pin ek of CN4002 on the VC-1025
board). If it is OK, check the focus motor drive IC (IC6800 on the VC-
1025 board).
E 2 0 0 0 Flash memory data are rewritten. Make flash memory data correct value. (Note 1)
E 3 1 0 0 Drive fault Turn power off and turn power on again.
E 4 1 0 0 Wi-Fi Module Hardware Error Check that connection between CN4902 on the VC-1025 board and
CN2301 on the WF-1004 board by FP-2200 flexible board.
E6 1 1 0
Zoom operations fault
(Cannot initialize zoom lens.)
Inspect the lens block zoom drive signal (pin eg of CN4002 on the VC-
1025 board when zooming is performed when the zoom lever is operated,
and the zoom motor drive circuit (IC6800 on the VC-1025 board) when
zooming is not performed.
*
*
*
()
*
Note 1: Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
Note 2: Functions of codes with * mark are not provided in this unit.

1-3
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-5. METHOD OF COPING WITH SHIFT LENS ERROR
VC-1025 BOARD (SIDE A)
C6814 C6815 C6816 C6817
R1401
IC6800
Fig. 1
Measurement points on the VC-1025 board
approx. 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R1401 on the VC-1025 board
Note 2: Functions of codes with * mark are not provided in this unit.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Self-diagnosis Code
Symptom/State Correction
Repaired by:
Block
Function
Detailed
Code
E6 1 1 1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E6 1 3 0
Reset position detection error on the step-
per iris initializing
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin wg, wh of CN4002 on theVC-1025 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
• Case of the iris blades do not close normally. Replace the lens block.
• Case of E: “61: 30” is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
• Case of LCD is not displayed normally. Check that connection between
CN6702 on CM-1004 board and CN4004 on VC-1025 board by FP-
2190 flexible board.
• Case of LCD is displayed normally. Replace the lens block.
E6 2 0 0
Handshake correction function does not
work well. (With PITCH angular velocity
sensor output stopped.)
Inspect PITCH angular velocity sensors (SE7701 on the JK-1009 board)
peripheral circuits.
E6 2 0 1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Inspect YAW angular velocity sensors (SE7701 on the JK-1009 board)
peripheral circuits.
E 6 2 0 2 Abnormality of IC for steadyshot. Refer to “1-5-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Occurred”.
E6 2 0 3
IC for steadyshot and micro controller
communication abnormality among. Inspect the steadyshot circuit (IC7711 on the VC-1025 board).
E6 2 0 4
Image vibration correction during hand-
shake function does not work.
Inspect the image vibration angular velocity sensors (SE7711 on the VC-
1025 board) peripheral circuits.
E 6 2 1 0 Shift lens initializing failure. Replacement of lens block (Note 3).
If an error occurs again, replace the VC-1025 board.
E 6 2 1 1 Shift lens overheating (Pitch) Refer to “1-5-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred”.
E 6 2 1 2 Shift lens overheating (Yaw) Refer to “1-5-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred”.
E 6 2 2 0 Abnormality of thermistor. Refer to “1-5-4. E : 62 : 20 (Abnormality of Thermistor) Occurred”.
E 6 2 3 0 Abnormal CPU Turn power off and turn power on again.
E 9 1 0 1 Abnormality when flash is being charged. Turn power off and turn power on again.
E 9 1 0 2 Abnormality of LED Video light. Turn power off and turn power on again.
E9 1 0 3
Abnormality of LED Video light Tem-
perature detection. Turn power off and turn power on again.
E9 2 0 1
Battery current value goes over the max
discharge current
Check the remaining battery power because this symptom maybe de-
pended on the remaining battery level, and confirm whether or not the
symptom is occurred after replacing the battery. If the symptom is still
occurred, overhaul inspection is needed. Check each output of DC/DC
converter (IC5100 on the VC-1025 board) with connected the DC JACK
(CN4007) on the VC-1025 board.
(The minimum connection to periphery)
E9 4 0 0
Fault of writing or erasing the flash
memory Inspect the flash memory (IC8101 on the MM-102 board).
E 9 4 0 1 Internal flash memory fault Inspect the flash memory (IC8101 on the MM-102 board).
E 9 4 0 2 BGM data error Check the CPU (IC6000 on the VC-1025 board).
E 9 5 0 0 GPS hardware error Turn power off and turn power on again.
E 9 6 0 0 Map area mount error Turn power off and turn power on again.
E 9 7 0 0 Projector hardware error Turn power off and turn power on again.
*
*
*
*
*

1-4
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-6. NOTE ON REPLACING PROJECTOR UNIT (Projector Model)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Note 2: Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK OK
NG NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED. ( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED. ( 1)
END
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40Syywwnnnnn Enter the red part.
(See page 1-5)
(See page 1-5)
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order Procedure
1 Turn the power OFF.
2While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power
ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect the camera
control circuit (IC6000 of VC-1025 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order Procedure
1 Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SERVICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3While setting the order 1, measure with an oscilloscope the output voltage of C6816 and C6817 in the periphery of IC6800 on the VC-
1025 board to check the output voltage varies.
4If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
5 Turn the power OFF.
6While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power
ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
7If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit IC6000 and IC6800 on the VC-1025 board periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Order Procedure
1 Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SERVICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3While setting the order 1, measure with an oscilloscope the output voltage of C6814 and C6815 in the periphery of IC6800 on the VC-
1025 board to check the output voltage varies.
4If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
5 Turn the power OFF.
6While measuring with an oscilloscope the output voltage of R1401 in the periphery of IC6800 on the VC-1025 board, turn the power
ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
7If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit IC6000 and IC6800 on the VC-1025 board periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order Procedure
1 Turn the power ON.
2 Confirm the connections of flexible flat cables and connectors between the lens block and VC-1025 board.
3In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens
replacement, replace VC-1025 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.

HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
1-5E
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED. ( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40Syywwnnnnn Enter the red part.
(See page 1-4)
(See page 1-4)

2-1
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link ACCESSORIES ASSEMBLY
･Abbreviation
BR : Brazilian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
JE : Tourist model
KR : Korea model
NE : North European Model
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: μF
• COILS
uH: μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...: μA... , uPA... , μPA... ,
uPB... , μPB... , μPC... , μPC... ,
uPD..., μPD...
The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark contain confiden-
tial information.
Strictly follow the instructions whenever the components
are repaired and/or replaced.
Destroy and discard the prescribed board and IC after
they are replaced.
Les composants identifiés par le symbole contiennent
des informations confidentielles.
Suivez scrupuleusement les instructions chaque fois
qu'un composant est remplacé et / ou réparé.
Veuillez détruire et éliminer les circuits imprimés et / ou
les circuits intégrés que vous avez remplacés.
标识有 的元件包含机密信息。
更换或维修元件时，请严格遵守指⽰。
更换后的电路板和IC，应予以报废。
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は,補修用部品であるため,回路図及びセットに付いてい
る部品と異なる場合があります。
• -XX,-Xは標準化部品のため,セットに付いている部品と異なる場合があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
 金 被：金属被膜抵抗。
 サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA...,uPA...,uPB...,uPC...,uPD...等はそれぞれμA..., μPA...,
μPB...,μPC...,μPD...を示します。
図面番号で部品を指定するときは基板名
又はブロックを併せて指定してください。
お願い
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してくださ
い。
• 外装部品色表示
例：
 (SILVER)：セットの色を表す。
 (Silver) ：部品の色を表す。
印の部品には，秘密情報が含まれています。
修理の際は，指示に従った対応を行ってください。
交換後の対象基板及び対象ICは，破壊のうえ廃棄し
てください。
q; Lens Block
• CM-1004 Board
• FP-2190 Flexible Board
qh LCD Block
• PD-1029 Board
• PJ-1009 Board
• FP-2106 Flexible Board
• FP-2193 Flexible Board
qh LCD Block
• PD-1028 Board
• FP-2184 Flexible Board
6IM Block
• MM-102 Board
• FP-2060 Flexible Board
qa JK Block
• JK-1009 Board
• FP-2191 Flexible Board
7Wi-Fi and NFC Block
• WF-1004 Board
• NFC Block Assy
• AN-1006 Flexible Board
• FP-2200 Flexible Board
Non Projector Model Projector Model
3L top Assy 8Control Switch Block (PS45300)
qg Built-In USB Cable
9Inner Cabinet Assy
4F Panel Assy
2Hinge Cover (R) 2Hinge Cover (R)
5Microphone Cabinet Block Assy
qs VC-1025 Board
qj Cabinet (R) Assy
1Cabinet (LR) Assy
qf DC Jack
qd Speaker
PJ340/PJ340E/
PJ350/PJ350E
View Position
Right View
Front View
Bottom View
Back View
Top View
Left View
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.03

2-2
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
– JAPANESE –
– ENGLISH –
作業時の注意
フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。
フレキシブル基板の導電面を素手で触れないようにしてください。
フレキシブル基板は，コネクターの奥までまっすぐに差し込んでください。(図1，図2，図3参照)
OK
(奥までまっすぐに差し込んである)
NG
(斜めに差し込んである)
NG
(差し込み不十分)
コネクター コネクター
フレキシブル
基板
基準線
フレキシブル
基板
コネクター コネクター
基準線
フレキシブル
基板
フレキシブル
基板
コネクター コネクター
基準線
フレキシブル
基板 フレキシブル
基板
図1 図2 図3
コネクターの開閉部を開ける際，A方向に開け過ぎないようにし
てください。
コネクターの開閉部を閉じる際，フレキシブル基板を矢印B方向
に押しながら，開閉部を均一に押してください。
開閉部
コネクター
フレキシブル基板
A
A
開閉部
絶縁面
コネクター
フレキシブル基板
B
• フラットケーブルおよびフレキシブル基板の端子面に欠け，
折れ等がないことを確認してください。
• 金メッキされているフレキシブル基板には，強い負担をかけ
ないでください。
先端の剥がれたメッキ部はカットして
除去してください。
（メッキ破片がコネクター内に残って
いる場合もあるので注意してください）
• コネクターを取り外す際に，線材部（極細）を持って引っ張る
と断線する恐れがありますので，絶対に線材部（極細）を持っ
て引っ張らないでください。
• 線材部（極細）を押さえながらコネクターを差し込むと，線材
部（極細）が断線する恐れがありますので，絶対に線材部（極細）
には負担をかけないでください。
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
NG
(The flexible board was plugged in
crooked.)
NG
(The flexible board was not plugged in
completely.)
Flexible
Board Flexible
Board
Connector Connector
Reference line Flexible
Board
Connector Connector
Flexible
Board
Reference line
Connector Connector
Flexible
Board
Flexible
Board
Reference line
Fig. 1 Fig. 2 Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
Holder
Connector Flexible Board
A
AHolder
Insulation side
Connector Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.

2-3
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
1 4-476-678-01 COVER (R (449)), HINGE (Non Projector Model)
2 4-476-677-01 COVER (R (4441)), HINGE (Projector Model) (BLACK)
2 4-476-677-11 COVER (R (4441)), HINGE (WHITE)
2 4-476-677-21 COVER (R (4441)), HINGE (BLUE)
3 A-1998-398-A LTOP ASSY (444B) (BLACK)
3 A-1998-399-A LTOP ASSY (444W) (WHITE)
3 A-1998-400-A LTOP ASSY (444L) (BLUE)
4 A-1998-352-A CABINET (LR) ASSY (449B) (BLACK, BLUE)
4 A-1998-354-A CABINET (LR) ASSY (449W) (WHITE)
#2 2-635-562-31 SCREW (M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
1. Remove in numerical order (1to 3) in the left figure.
DISASSEMBLY
1Open the LCD (1) →#12 X 1
Screw
1
Right View
#12
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
2#2 X 2
Back View
#2
#2
Bottom View
3#2 X 1 →#12 X 2→#2 X 2 →#12 X 1
Right View Left View
#12
#12
#2
#2
#12
Bottom View
機種によって形状がイラストと異なる場合があります。
The shape may be different from the illustration depending
on models.
A
A
(Claws)
(Claw)
(Claw)
Projector
Model
Non Projector
Model
Front Section
(See page 2-4)
Front Section
(See page 2-4)
2
1
1
1
22
14
33
#2
#2
#12
#12
#12
#12
ns
#2
#2

2-4
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1-2. FRONT SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
51 A-1998-367-A CABINET BLOCK ASSY, MICROPHONE
52 4-447-694-01 CUSHION, MIC
*53 4-533-725-01 SHEET (WF (453)), SHIELD
54 A-1998-402-A PANEL ASSY (444), F
MIC901 1-542-999-21 MICROPHONE UNIT
#11 3-078-890-11 SCREW, TAPPING
#12 3-080-204-21 SCREW, TAPPING, P2
1. Remove in numerical order (1to 2) in the left figure.
DISASSEMBLY
(Claw)
(Hook)
Lens Section
(See page 2-5)
1
2
#11
#11
ns
ns
ns ns
ns
ns
ns
ns
#12
MIC901
51
52
53
54
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
2#12 X 1
#12
Left View

2-5
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1-3. LENS SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
101 8-848-900-01 DEVICE, LENS LSV-1610A
102 1-856-432-21 FILTER BLOCK, OPTICAL (Note 2)
103 4-436-733-01 RUBBER (1610), SEAL
104 A-1903-090-A CM-1004 BOARD, COMPLETE (including CP001
(CMOS imager)) (Note 1)
105 1-889-184-11 FP-2190 FLEXIBLE BOARD
106 1-889-592-11 AN-1006 FLEXIBLE BOARD
107 A-1992-200-A WF-1004 BOARD, COMPLETE
108 1-889-209-11 FP-2200 FLEXIBLE BOARD
109 A-2040-416-A NFC BLOCK ASSY (14Y_TERA) COMP (Note 3)
110 4-489-010-01 SHEET (ANT), ADHESIVE
111 4-274-987-01 TAPE (AS 1/2) (C)
112 1-887-155-11 FP-2060 FLEXIBLE BOARD (PJ340/PJ340E/PJ350/
PJ350E)
113 A-1992-197-A MM-102 BOARD, COMPLETE (PJ350/PJ350E)
113 A-1994-766-A MM-102 BOARD, COMPLETE (PJ340/PJ340E)
114 1-492-709-11 SWITCH BLOCK, CONTROL (PS45300)
115 A-1998-288-A CABINET ASSY (449), INNER
#2 2-635-562-31 SCREW(M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
#140 2-635-562-01 SCREW (M1.7)
#172 2-178-410-01 TITE (UB TITE) 1.4
1. Remove in numerical order (1to 5) in the left figure.
DISASSEMBLY
1#140 X 1
Screw
#140
Left View
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#140: M1.7X 2.0
(Black)
2-635-562-01
2.0
1.7
#172: M1.4 X 4.0 (Tapping)
(Black)
2-178-410-01
1.4
4.0
B
C
A
A
B
C
(Claw)
Cabinet (R) Section
(See page 2-6)
PJ340/PJ340E/PJ350/PJ350E
1
2
3
5
4
(including CP001
(CMOS imager))
(Note 1)
#172
#140
#172
#140
#12
#12
#2
#2
101
115
105
106
108
111
110
109
(Note 3)
112
113
114
107 102
(Note 2)
104
103
2#140 X 2
#140
Left View
3#12 X 1 →#2 X 1
#12
#2
Left View
Top View
4#2 X 1 →#12 X 1
#2 #12
Right View Top View
5#172 X 2
#172
Left View
Note
Note 1: Be sure to read “Precautions for Replacement of Imager”
on page 6-1 of Level 3 when changing the imager.
Note 1: イメージャの交換時はLevel3の6-1ページ，“イメージャ交
換時の注意”を必ずお読みください。
Note 2: Refer to “Assembly-2: How to distinguish the side of Optical
Filter Block facing to Lens Device”.
Note 2:
“Assembly-2:HowtodistinguishthesideofOpticalFilter
BlockfacingtoLensDevice”を参照してください。
Note 3: Be careful not to break the NFC Block Assy. Note 3: NFC部組を折らないよう注意してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.03

2-6
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1-4. CABINET (R) SECTION
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
151 A-1994-767-A VC-1025 BOARD, COMPLETE (SERVICE)
(Non Projector Model)
151 A-1994-768-A VC-1025 BOARD, COMPLETE (SERVICE)
(Projector Model)
152 1-838-712-32 CABLE, BUILT-IN USB
153 4-476-262-01 RETAINER (453), HDMI
154 1-889-185-11 FP-2191 FLEXIBLE BOARD
155 A-1994-762-A JK-1009 BOARD, COMPLETE
*156 3-283-835-01 CUSHION, SP
157 A-1998-390-A CABINET (R) ASSY (444) (Non Projector Model)
157 A-1998-391-A CABINET (R) ASSY (4441) (Projector Model)
158 3-283-643-21 SCREW, TRIPOD (Note 2)
J901 1-842-658-71 JACK, DC
SP901 1-858-075-41 SPEAKER (1.8CM)
#2 2-635-562-31 SCREW(M1.7)
#12 3-080-204-21 SCREW, TAPPING, P2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 1)
1. Remove in numerical order (1to 3) in the left figure.
DISASSEMBLY
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
1.7
5.0
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
1#12 X 1
#12
Front View
Note
Note 1: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 1: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
Note 2: When removing / attaching this part, be careful not to dam-
age the peripheral parts.
Note 2: この部品を取り外し，取り付けるときは，周囲の部品を破
損しないよう注意してください。
A
B
B
A
Projector Model
Non Projector
Model
LCD Section
(Projector Model)
(See page 2-7)
LCD Section
(Non Projector Model)
(See page 2-8)
1
3
3
2
SP901
#12
#12
#2
J901
ns
#288
(Note 1) #2
155
154
151
152
158
(Note 2)
156
157
153
2Open the Jack Lid (2) →#2 X 1 →#12 X 1
#2 #12
2
Right View Top View
3#288 X 2
#288
Left View

2-7
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-1-5. LCD SECTION
(Projector Model)
Refer to page 2-8 about Non Projector Model.
ns: not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
201 A-1998-404-A CABINET (C) ASSY (4441B), P (PJ340 (BLACK)/
PJ340E (BLACK))
201 A-1998-405-A CABINET (C) ASSY (4441W), P (WHITE)
201 A-1998-410-A CABINET (C) ASSY (4441L), P (BLUE)
201 A-1998-411-A CABINET (C) ASSY (4441B), P (PJ350/PJ350E)
201 A-1998-412-A CABINET (C) ASSY (4441B), P (PJ330E)
202 4-476-581-01 HEAT SINK (4441), P
203 A-1903-100-A FP-2106 FLEXIBLE BOARD, COMPLETE
204 4-272-358-01 CUSHION, P
205 A-1847-133-A LSV-1580A (Note 4)
206 A-1994-765-A PJ-1009 BOARD, COMPLETE
207 A-1994-888-A PD-1029 BOARD, COMPLETE (SERVICE)
208 4-209-715-01 JOYSTICK
209 4-476-577-01 INSULATING SHEET (4441)
210 4-476-573-01 KNOB (4441), FOCUS
211 4-476-580-01 RETAINER (4441), LCD
212 4-476-566-01 CUSHION (4441), LCD
213 4-476-579-01 PLATE (4441), PANEL GROUND
214 4-476-572-01 BUTTON (4411), PLAYBACK (PJ)
215 4-476-561-01 CABINET (M (4441)), P
216 4-476-671-01 COVER (C (4441)), HINGE (BLACK)
216 4-476-671-11 COVER (C (4441)), HINGE (WHITE)
216 4-476-671-21 COVER (C (4441)), HINGE (BLUE)
217 X-2585-820-2 HINGE (P) (Y (4071)) ASSY
218 1-471-573-11 MAGNET (Note 5)
219 4-476-570-01 COVER (M (4441)), HINGE
220 1-889-187-11 FP-2193 FLEXIBLE BOARD (Note 3)
221 4-272-354-01 SHEET, P RADIATION
222 4-476-583-01 SHEET PJ (4441)
BH4600 1-251-928-21 SOCKET, BATTERY (Note 1)
BT4600 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
LCD901 1-811-218-31 LCD MODULE
#2 2-635-562-31 SCREW (M1.7)
#11 3-078-890-11 SCREW, TAPPING
#30 3-086-156-11 SCREW B1.2
#288 2-187-345-21 SCREW (M1.7), P2 (Note 2)
B
B
A
C
D
D
A
(Claws)
(Claws)
C
BT4600
(Note 1)
BH4600
ns
LCD901
(Note 1)
Adjust the position.
: BT4600 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-54 of Level 3)
#2
#2
#11
#11
#30
201
207
216
217
218
(Note 5)
219
208
209 211
212
213 214
210
202
222
205
(Note 4)
203
204
221
206
215
#288
(Note 2)
220
(Note 3)
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3.5
1.2
Note
Note 1: Replace the battery holder (BH4600) together when replac-
ingthe lithium storage battery (BT4600) on the PD-1029
board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note 1: PD-1029基板のリチウム蓄電池(BT4600) を交換する場合は
バッテリホルダ(BH4600) も同時に新品に交換してくださ
い。
 (一度使用したバッテリホルダは再使用できません。)
 部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP-
2193”.
Note 3: “Assembly-1:InstallationMethodofFP-2184/FP-2193”を参
照してください。
Note 2: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 2: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
Note 4
PRECAUTIONS WHEN HOLDING THE PROJECTOR UNIT
Lens part
Sheet
The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Copper Plate
Copper Plate
Contact area o
f
Flexible Board
Terminal of
Connector
Very weak
(Don't hold)
Lever
Weak
(Handling attention)
Have to wear
finger stall
Note 5:
Marking
Install the magnet with
the marking oriented
as shown below.
Note 4
プロジェクターを使用した後は，プロジェクターユニットが熱くなっています。
特に銅板の部分は高温になります。
部品を交換する時は，温度が下がってから作業を行なってください。
プロジェクターユニットを持つ際の注意
銅板
銅板 コネクタ部
フレキ接点
レバー
非常に弱い 弱い 指サック着用
のこと
シート
レンズ部
マーキング
Note 5: マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
くだ さ い 。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.03

2-8
HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
251 4-476-667-01 CABINET (C (449)), P
252 4-274-987-01 TAPE (AS 1/2) (C)
253 A-1994-877-A PD-1028 BOARD, COMPLETE (SERVICE)
254 4-209-715-01 JOYSTICK
255 4-446-970-01 INSULATING SHEET (409)
256 4-476-576-01 PLATE (441), PANEL GROUND
257 4-476-572-11 BUTTON (4411), PLAYBACK (PJ)
258 4-476-562-01 CABINET (M (444)), P
259 4-476-672-01 COVER (C (449)), HINGE
260 X-2585-819-1 HINGE (Y (409)) ASSY, T TYPE
Ref. No. Part No. Description
Ref. No. Part No. Description
261 1-471-573-11 MAGNET (Note 4)
262 4-476-560-01 COVER (M (449)), HINGE
263 1-889-097-11 FP-2184 FLEXIBLE BOARD (Note 3)
BH4500 1-251-928-21 SOCKET, BATTERY (Note 1)
BT4500 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
LCD901 1-811-218-31 LCD MODULE
#2 2-635-562-31 SCREW(M1.7)
#11 3-078-890-11 SCREW, TAPPING
#288 2-187-345-21 SCREW (M1.7), P2 (Note 2)
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
4.0
1.7
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
4.0
1.7
#288: M1.7 X 2.5
(Black)
2-187-345-21
2.5
1.7
2-1-6. MOUNT SECTION
(Non Projector Model)
Refer to page 2-7 about Projector Model.
ns: not supplied
(Claws)
A
A
(Claws)
BT4500
(Note 1)
ns
LCD901
BH4500
(Note 1)
: BT4500 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-53 of Level 3)
#2
#2
#11
#288
(Note 2)
251
252
253
255
256
257
258
259
260
263
(Note 3)
261
(Note 4)
262
254
Note
Note 1: Replace the battery holder (BH4500) together when replac-
ing the lithium storage battery (BT4500) on the PD-1028
board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium storage battery next.
Note 1: PD-1028基板のリチウム蓄電池(BT4500) を交換する場合は
バッテリホルダ(BH4500) も同時に新品に交換してくださ
い。
 (一度使用したバッテリホルダは再使用できません。)
 部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Note 3: Refer to “Assembly-1: Installation Method of FP-2184/FP-
2193”.
Note 3: “Assembly-1:InstallationMethodofFP-2184/FP-2193”を参
照してください。
Note 2: This screw cannot be reused. Discard the screw removed
once in servicing. Instead, use a new screw.
Note 2: このねじは再利用することができません。サービス対応時
に一度でも外した場合は新品のねじと交換してください。
Note 5:
Marking
Install the magnet with
the marking oriented
as shown below.
マーキング
Note 5: マグネットを取付ける
際は，マ−キング面を
図の位置にあわせて
くだ さ い 。

HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
2-9E
ACCESSORIES
901 902 903 904 905
Ref. No. Part No. Description
8-022-373-30 Rechargeable battery pack NP-FV50/UC (US, CND)
8-022-373-50 Rechargeable battery pack NP-FV50/CE (EXCEPT US, CND, NE, CH)
8-022-373-55 Rechargeable battery pack NP-FV50/RU (NE)
8-022-373-71 Rechargeable battery pack NP-FV50/CN (CH)
Ref. No. Part No. Description
901 1-492-768-12 AC Adaptor (US, CND, JE, E: NTSC)
901 1-492-768-21 AC Adaptor (CH)
901 1-492-769-11 AC Adaptor (AEP, NE, E: PAL)
901 1-492-769-21 AC Adaptor (BR)
901 1-492-769-31 AC Adaptor (KR)
901 1-492-771-11 AC Adaptor (UK, HK)
902 1-569-007-12 Conversion (2P) Adaptor (E: NTSC, JE)
903 1-838-714-31 USB connection support cable
904 1-846-028-21 HDMI cable
*905 4-529-735-11 Operating Guide (ENGLISH)
*905 4-529-735-21 Operating Guide (SPANISH)
*905 4-529-735-41 Operating Guide (TRADITIONAL CHINESE)
*905 4-531-076-21 Operating Guide (KOREAN)
Ref. No. Part No. Description
*905 4-531-077-11 Operating Guide (GERMAN, DUTCH, ITALIAN,
PORTUGUESE)
*905 4-531-077-21 Operating Guide (GREEK, POLISH, CZECH,
HUNGARIAN)
*905 4-531-077-31 Operating Guide (SLOVAK, SWEDISH, DANISH,
FINNISH, ROMANIAN)
*905 4-531-077-41 Operating Guide (RUSSIAN)
*905 4-531-077-51 Operating Guide (UKRAINIAN)
*905 4-531-077-61 Operating Guide (SIMPLIFIED CHINESE)
*905 4-531-077-71 Operating Guide (ARABIC, PERSIAN)
*905 4-531-077-81 Operating Guide (TURKISH)
*905 4-531-078-31 Operating Guide (SIMPLIFIED CHINESE)
This Item is not supplied with the unit as an accessory, but it is prepared as a service part.
When the customer requests printed one, ask Head Quarter.
941
Ref. No. Part No. Description
*941 4-531-073-11 Help Guide (ENGLISH)
*941 4-531-073-21 Help Guide (FRENCH)
*941 4-531-073-31 Help Guide (SPANISH)
*941 4-531-073-41 Help Guide (GERMAN)
*941 4-531-073-51 Help Guide (ITALIAN)
*941 4-531-073-61 Help Guide (DUTCH)
*941 4-531-073-71 Help Guide (PORTUGUESE)
*941 4-531-073-81 Help Guide (BRAZILIAN PORTUGUESE)
*941 4-531-073-91 Help Guide (TURKISH)
*941 4-531-074-11 Help Guide (GREEK)
*941 4-531-074-21 Help Guide (CZECH)
*941 4-531-074-31 Help Guide (HUNGARIAN)
*941 4-531-074-41 Help Guide (SLOVAK)
*941 4-531-074-51 Help Guide (POLISH)
*941 4-531-074-61 Help Guide (SWEDISH)
*4-531-074-71 Help Guide (DANISH)
Ref. No. Part No. Description
*941 4-531-074-71 Help Guide (DANISH)
*941 4-531-074-81 Help Guide (FINNISH)
*941 4-531-074-91 Help Guide (ROMANIAN)
*941 4-531-075-11 Help Guide (RUSSIAN)
*941 4-531-075-21 Help Guide (UKRAINIAN)
*941 4-531-075-31 Help Guide (TRADITIONAL CHINESE)
*941 4-531-075-41 Help Guide (SIMPLIFIED CHINESE)
*941 4-531-075-51 Help Guide (KOREAN)
*941 4-531-075-61 Help Guide (ARABIC)
*941 4-531-075-71 Help Guide (PERSIAN)
*941 4-531-075-81 Help Guide (INDONESIAN)
*941 4-531-075-91 Help Guide (THAI)

HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
3-1E
3. ASSEMBLY
Assembly-1: The Method of attachment of FP-2184/FP-2193
Flexible Board
1Fold dotted line parts of the FP-2184/FP-2193 flexible
board as shown in figure.
Adhesive tape Adhesive tape
Adhesive tape
Adhesive tape
Adhesive tape
Adhesive tape
Valley fold
Valley fold
Mountain fold
FP-2193
Flexible Board
FP-2184
Flexible Board
Mountain fold
Valley fold
2Roll the FP-2184/FP-2193 Flexible Board 2 times
in the Hinge Assy as shown in figure.
3Install the Cover (M) Hinge/Cover (C) Hinge.
Cover (M) Hinge
Cover (C) Hinge
2 Times
4Attach the FP-2184/FP-2193 Flexible Board as
shown in figure.
Flexible Board
Hinge Assy
FP-2184/FP-2193
Flexible Board
Assembly-2: How to distinguish the side of Optical Filter Block
facing to Lens Device
• IR cut coating surface
The red coating is reflected.
• The other surface
The red coating is
not reflected. • Side view
The red belt
is seen.
Lens Device side
Lens Device side
Hold it with tweezers or the like.
Optical Filter Block
[IR Cut Coated Side] [The Other Side]
The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).

HDR-CX330/CX330E/PJ330E/PJ340/PJ340E/PJ350/PJ350E_L2
7-1E
7. ADJUSTMENT
(ENGLISH)
For adjusting these models, the Adjust manual and the Adjust station are required.
Adjust station
It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.
Adjust manual
It is the software to adjust and check digital cameras and camcorders for service.
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.
Note 1: Be sure to install Adjust station first.
Note 2: To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
Install the Adjust manual of the DSC-WX50 series in advance.
(JAPANESE)
これらの機種で調整を行なうには，アジャストマニュアルとアジャストステーションが必要です。
アジャストステーションとは
機種別のアジャストマニュアルを起動するためのソフトウェアです。
アジャストステーションのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認してくださ
い。
アジャストマニュアルとは
デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで，調整及び各種動作確認を行うことが可能です。
アジャストマニュアルのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認してください。
注意1： インストールは必ずAdjuststationを先に行なってください。
注意2： この機種で仕向け設定を行うには，DSC-WX50シリーズの Adjustmanualがインストールされている必要があ
ります。
 先にDSC-WX50シリーズのAdjustmanualをインストールしてください。