Sony WALKMAN WM-FX483 User manual

House Current
Connect the AC power adaptor AC-E30HG (not
supplied) to the DC IN 3 V jack and to the mains. Do not
use any other AC power adaptor.
Specifications for AC-E30HG varies for each area. Check
your local voltage and the shape of plug before
purchasing.
To use the belt clip
With the supplied belt clip, you can wear your Walkman
on a belt for convenient use.
To remove the belt clip
To attach the belt clip
Connecting the Headphones/
Earphones
2
2
1Connect the headphones/earphones to 2.
2Wear the “L” marked side to the left ear and the “R”
marked side to the right ear.
If the earphones do not fit to your ears or the sound is
unbalalnced, turn round the earphones a little to fit to
your ears firmly.
p
œ
REW
FF
zOperating the Walkman
Playing a Tape
1Open the cassette holder and insert a cassette.
2Make sure the HOLD function is turned off.
If it is on, slide the HOLD switch to turn it off.
3Press MENU repeatedly to set the cursor to TAPE in
the display.
Then press SET to select the tape type.
No message: normal (TYPE I)
METAL: CrO2(TYPE II) or metal (TYPE IV)
4Press œ(play) to start playing then adjust the
volume.
When adjusting the volume on the Walkman (FX487
only)
Set the VOL control on the remote control at maximum.
When adjusting the volume on the remote control
(FX487 only)
Set the VOL control on the Walkman slightly above the
appropriate level.
Note on the cassette holder
When opening the cassette holder, press the p(stop) button and
make sure the tape is stopped by checking through the cassette
window, then slide the OPEN switch.
If the cassette holder is opened before the tape is stopped, the
tape may loosen and be damaged.
TAPE
HOLD
VOL
SET
œ
MENU
HOLD
œ
VOL
TAPE
HOLD
VOL
SET
œ
MENU
Sony Corporation 1998 Printed in Malaysia
Radio Cassette Player
Operating Instructions
zGetting Started
Preparing a Power Source
Dry Battery
Open the battery compartment lid, and insert two size
AA (R6) dry batteries with correct polarity.
If the battery compartment lid comes off
When to replace the batteries
Replace the batteries when “n” flashes in the display.
The battery remainder mark has 3 steps to show the
remaining battery power.
The battery power is full.
The battery power is decreasing.
The batteries are exhausted.
Replace them with new ones.
Notes
•The battery remainder mark may temporarily show a lower
level during fast forwarding or rewinding or use in extremely
low temperatures.
•When replacing batteries, replace both batteries within 30
seconds; otherwise all the memories including the preset radio
stations will be canceled.
Battery life (Approx. hours) (EIAJ*)
Tape playback Radio reception
Sony alkaline LR6 (SG) 24 38
Sony R6P (SR) 7.5 14
* Measured value by the standard of EIAJ (Electronic Industries
Association of Japan). (Using a Sony HF series cassette tape)
Note
•The battery life may shorten depending on the operation of the
unit.
For maximum performance we recommend that you use
alkaline batteries.
3-861-494-13(1) Listening to the Radio
VOL
HOLD
RADIO ON
/BAND
p•RADIO OFF
TUNING +/–
VOL
HOLD
RADIO ON/BAND
p•RADIO OFF
TUNING +/–
1Make sure the HOLD function is turned off.
If it is on, slide the HOLD switch to turn it off.
2Press RADIO ON/BAND to turn on the radio.
3Press RADIO ON/BAND repeatedly to select FM1,
FM2, FM3 or AM.
4Press TUNING+/– to tune in to the desired station.
If you keep pressing TUNING+/– for a few seconds,
the Walkman will start tuning to the stations
automatically.
To turn off the radio
Press p•RADIO OFF .
WM-FX487/FX485/FX483
For the customers in the U.S.A.
OWNER'S RECORD
The model number is located at the bottom and the serial
number is located inside the cassette holder. Record the model
and serial numbers in the spaces provided below. Refer to these
numbers whenever you call upon your Sony dealer regarding
this product.
Model No. _________________ Serial No.___________________
INFORMATION
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for
help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
About This Manual
The instructions in this manual are for WM-FX487, WM-
FX485 and WM-FX483. Before you start reading, check
your model number. WM-FX487 is the model used for
illustration purposes. Any differ2ences in operation are
clearly indicated in the text, for example, “FX487 only”.
WALKMAN is a registered trademark of Sony Corporation.
1
2
To select playback mode
Press MENU repeatedly to set the cursor to MODE in the
display. Then press SET to select the desired mode.
To play Select
Both sides repeatedly a
Both sides once from the side Å
facing the cassette holder
To play a tape recorded with Dolby* NR system
(FX487/FX485 only)
Press MENU repeatedly to set the cursor to aNR
(Dolby noise reduction) in the display. Then press SET to
show “ON”.
* Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
“DOLBY”and the double-D symbol aare trademarks of
Dolby Laboratories Licensing Corporation.
FX487 FX485/FX483
œ
FF
p
REW
œ
FF
p
REW
SET
MENU
MODE aNR
FX487
FX485/FX483
FX487
FX485/FX483
FX487
SET
MENU
MODE aNR MODE
FX485 FX483
FX487
FX485/FX483
turn over m
To Press
play the other side œ (play) during playback
stop playback p
fast forward FF during stop
rewind REW during stop
play the same side from the REW during playback
beginning (Rewind Auto
Play function)
play the other side from the FF during playback
beginning (Skip Reverse
function)
OPEN
Polarity of
the plug

To improve the broadcast reception
•For FM: Extend the cord of the remote control , the
aerial (FX487 only). Extend the headphones/earphones
cord, the aerial (FX485/FX483 only). If the reception is
still not good, press MENU repeatedly to set the cursor
to FM MODE or FM SENS in the display. Then press
SET to choose the mode for best reception.
•For AM: The Walkman has a built-in antenna. Reorient
the Walkman horizontally to obtain optimum AM
reception.
Note
•Do not remove the power sources while listening to the radio,
or the received stations may not be stored.
Presetting Radio Stations
You can store radio stations into the unit’s memory. You
can preset up to 20 radio stations, 5 for each FM1, FM2,
FM3 or AM bands.
RADIO ON
/BAND
1~5
PRESET +/–
BAND
(RADIO ON•BAND)
1~5
RADIO ON/BAND
1Tune in the station you wish to store. (Follow steps 1-
4 in “Listening to the Radio”.)
2Press and hold one of the 1-5 buttons for more than 2
seconds. The display flashes twice with a beep sound,
and the station is preset.
If a station is already stored, and the new station
replaces the old one.
To play the preset radio stations
1Press RADIO ON/BAND to select the band.
2Press the corresponding button (1-5) on the unit.
Or press PRESET+/– on the remote control (FX487
only).
Receiving Stations Outside
Your Country (Excluding
models for Europe and Saudi
Arabia)
The frequency range differs depending on the area (see
the chart “Area indication and frequency range”). If you
listen to the radio in an area of different frequency range,
change the area indication in the display.
RADIO ON
/BAND
TUNING +/–
RADIO ON/BAND
TUNING +/–
1Turn on the radio and press RADIO ON/BAND for
more than 10 seconds until the area indication flashes
in the display.
2While the display is flashing, press TUNING+/– to
select either “U” or “E” indication.
3Press RADIO ON/BAND to set the area indication.
Note
•If you change the frequency range, all the preset stations will
be canceled.
Area indication and frequency range
Area* Frequency range
FM (MHz) AM (kHz)
E 87.5–108 531–1,602
U 87.5–108 530–1,710
* E: European and other countries
U: USA, Canada, and Central and South America
zAdditional Information
Precautions
On batteries
•Do not charge a dry battery.
•Do not carry the dry or rechargeable batteries with
coins or other metallic objects. It can generate heat if the
positive and negative terminals of the batteries are
accidentally contacted by a metallic object.
•When you do not use the Walkman for a long time,
remove the battery to avoid any damage caused by
battery leakage and subsequent corrosion.
On the unit
•Do not drop the unit or give a shock to the unit, or it
may cause a malfunction.
•Do not leave the unit in a location near heat sources, or
in a place subject to direct sunlight, excessive dust or
sand, moisture, rain, mechanical shock, or in a car with
its windows closed.
•The LCD display may become hard to see or slow down
when using the unit at high temperatures (above 40°C/
104°F) or at low temperatures (below 0°C/32°F). At
room temperature, the display will return to its normal
operating condition.
•If the unit has not been used for long, set it in the
playback mode and warm it up for a few minutes
before inserting a tape.
On tapes longer than 90 minutes
We do not recommend the use of tapes longer than 90
minutes except for a long continuous playback. They are
very thin and tend to be stretched easily.
On the remote control (FX487 only)
Use the supplied remote control only with this unit.
On headphones/earphones
Road safety
Do not use headphones/earphones while driving,
cycling, or operating any motorized vehicle. It may create
a traffic hazard and is illegal in some areas. It can also be
potentially dangerous to play your headphones/
earphones at high volume while walking, especially at
pedestrian crossings.
You should exercise extreme caution or discontinue use
in potentially hazardous situations.
Preventing hearing damage
Do not use headphones/earphones at high volume.
Hearing experts advise against continuous, loud and
extended play. If you experience a ringing in your ears,
reduce volume or discontinue use.
Caring for others
Keep the volume at a moderate level. This will allow you
to hear outside sounds and to be considerate to the
people around you.
If you have any questions or problems concerning your
unit, please consult you nearest Sony dealer.
Troubleshooting
The volume cannot be turned up.
•If “ ” appears for AVLS display, press SET so that “ ”
disappears.
The sound is unstable or no audio.
•Insert two R6 (size AA) batteries properly.
•Replace all batteries if they are weak.
The display shows incorrect information.
•The batteries are weak. Replace the batteries with new
ones.
Specifications
Radio section
Frequency range
FM: 65–74/87.5–108 MHz (Eastern Europe)
87.5–108 MHz (other countries)
AM: 530–1,710 kHz (North, Central and South America)
531–1,602 kHz (other countries)
Tape section
Frequency response
(Dolby NR off)
Playback: 30–14,000 Hz
Output
Headphones/earphones (2jack)
Load impedance 8–300 ohms
General
Power requirements
3 V
Two size AA (R6) batteries
Dimensions (w/h/d)
FX487:
Approx. 115.5 x 83.5 x 35.5 mm (45⁄8 x 33⁄8x 17⁄16 inches) incl.
projecting parts and controls
FX485/FX483:
Approx. 115.5 x 83.5 x 34.0 mm (45⁄8 x 33⁄8x 13⁄8inches) incl.
projecting parts and controls
Mass
Approx. 150 g (5.3 oz)/Approx. 230 g (8.2 oz) incl. batteries
and a cassette
Supplied accessories
Stereo headphones or Stereo earphones with remote control
(1) (FX487 only)
Stereo headphones or Stereo earphones (1) (FX485/FX483
only)
Belt clip (1)
Design and specifications are subject to change without notice.
Maintenance
To clean the tape head and path
Use the cleaning cassette CHK-1
(not supplied) every 10
hours of use.
Note
•Use only the recommended cleaning cassette.
To clean the exterior
Use a soft cloth slightly moistened with water. Do not
use alcohol, benzine or thinner.
Note
•Clean the headphones/earphones plug periodically.
For the customers in the U.S.A.
Using Other Functions
To emphasize bass sound
Press MENU repeatedly to set the cursor to SOUND in
the display. Then, press SET to select the desired mode.
With each press, the indications change as follows.
MB (MEGA BASS) : emphasizes bass sound
GRV (GROOVE) : emphasizes deeper bass sound
No message: off (normal)
Notes
•If the sound is distorted with the mode “GRV”, select the mode
“MB” or no message.
•Bass emphasis may not show great effect if the volume is
turned up too high.
To protect your hearing—AVLS
(Automatic Volume Limiter System)
When you set the AVLS function to active, the maximum
volume is kept down to protect your ears.
Press MENU repeatedly to set the cursor to AVLS in the
display. Then press SET to show “ ”.
Notes
•If the sound is distorted when you listen to the bass-boosted
sound with the AVLS function, turn down the volume.
•The AVLS setting may be canceled when you replace the
batteries.
To lock the controls
Set the HOLD switch to the direction of the arrow to lock
the controls.
SET
MENU
SET
MENU
FX487
FX485/FX483
FX487
FX485/FX483
MODE AVLS SOUND
SET
MENU
MODE AVLS SOUND
SET
MENU
FX487
FX485/FX483
(MONO ST)
FM MODE
(LOCAL DX)
FM SENS
FX487
FX485/FX483
or
HOLD
HOLD