Sony ICD-R100PC Operating Instructions (primary... User manual

Ver 1.0 1999.05
MICROFILM
ICD-R100PC
SERVICE MANUAL
IC RECORDER
SPECIFICATIONS
US Model
Canadian Model
AEP Model
Connection cable x 1
Froppy disc x 3

– 2 –
Specifications ........................................................................... 1
1. SERVICING NOTE....................................................... 2
2. GENERAL ....................................................................... 3
3. DISASSEMBLY
3-1. Lid ASSY, Upper ........................................................ 5
3-2. Digital Board .............................................................. 5
3-3. Unit, Switch ................................................................ 6
3-4. Jack Board .................................................................. 6
3-5. Main Board ................................................................. 6
4. DIAGRAMS
4-1. Explanation of IC Terminals....................................... 7
4-2. Block Diagrams .......................................................... 9
4-3. Printed Wiring Boards (Main Section) ......................11
4-4. Schematic Diagram (Main Section) ......................... 13
4-5. Printed Wiring Boards (Digital Section) .................. 17
4-6. Schematic Diagram (Digital Section)....................... 18
5. EXPLODED VIEWS
5-1. Case Section ............................................................. 23
5-2. Main Board Section .................................................. 24
6. ELECTRICAL PARTS LIST.................................... 25
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TABLE OF CONTENTS
Jig (J-2503-010-A)
Main boar
d
Digital board
SECTION 1
SERVICING NOTE
Using the special connector jig (J-2503-101-A) to connect the main
board and digital board will prove convenient when servicing the
unit with power applied.
Note : Do not apply excessive amounts of flux during replace-
ment of electronic components since this may cause elec-
trical shorts due to moisture.
Wipe off flux after electronic components exchange.
CAUTION ON REPLACING FLASH MEMORY
The BAD-BLOCK check* must be executed, when the flash
memory (IC701) in this set was replaced.
The set will not operation normally, unless this check is finished.
* The BAD-BLOCK check detects an area (bad-block) in the flash
memory where data validity cannot be guaranteed, and saves
this information in the TOC-AREA so that a bad-block is not
used.
BAD-BLOCK check procedure :
1. Apply 3V from regulated power supply to the battery
terminals.
2. Once the power is supplied, the check starts and then
proceeds for approx. 3 minutes. (Be sure to keep applying
the power during the check)
3. When the check completes, the result is shown as bellows.
OK: Only the LCD back light LED (D503, 504) turns on.
NG: Red LED blinks or turns on or green LED turns on in
the OPR LED (D502),
4. In case of OK, press the STOP button.
Note :
• In case of NG, check system control IC (IC704), flash memory
IC (IC701) and the peripheral circuit. (Particularly, check care-
fully the soldering of the flash memory)
• After finishing the BAD-BLOCK check, assemble the set, load
the dry battery, and confirm if the set operates normally.

– 3 –
SECTION 2
GENERAL
LOCATION AND FUNCTION OF CONTROLS
This section is extracted from
instruction manual.

– 4 –

– 5 –
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. LID ASSY, UPPER
rThe equipment can be removed using the following procedure.
Set Lid ASSY, Upper Unit, Switch
Digital board Jack board Main board
Case ASSY
2 Screws (B1.7X9)
1 Screw (B1.7X10
)
4
3 Remover solder
Lid ASSY, Upper
3-2. DIGITAL BOARD
Digital board
Case ASSY
2
1
Remove the
connector
(CN703)
Note : Not using a screw (10mm) of step
1for this place.

– 6 –
3-4. JACK BOARD
3-5. MAIN BOARD
Case ASSY
1 Screw (B1.7X4)
Jack boar
d
2 Remove the
connector
(CN102)
3
Cap (PC)
Case ASS
Y
2 Claw
3 Claw
Main boar
d
Cap (Terminal)
4
1
3-3. UNIT, SWITCH
Unit, Switch
Digital board
Double-sided adhesive tap
e
2
1
Note : The switch unit is secured with double-sided
adhesive tape.
When removed the switch unit, change it for
a new component.

– 7 –
SECTION 4
DIAGRAMS
4-1. EXPLANATION OF ICTERMINALS
IC704 µPD780308GC-113-8EU (SYSTEM CONTROL)
Pin No. Pin name I/O Description
1 KEY0 I Key input
2 KEY1 I Key input
3 SPDSW I Playback speed switch input.
4 XHOLD I Hold switch input.
5 HPMUTE O Earphone mute output.
6 PCLE O PC link permission signal output.
7 XFMCE O CE output for flash memory.
8 VDDO – Power supply terminal.
9 AVREF I A/D reference voltage input.
10 XFMWE O Write enable signal output for flash memory.
11 XFMALE O ALE signal output.
12 VSS1 – Ground.
13 XFMR/B I Flash memory Ready/Busy signal input.
14 XFMCLE O CLE signal output for flash memory.
15 SYNCOUT O SYNC signal output.
16 SYNCMSK O SYNC output control signal output.
17 XFMRE O Flash memory read enable signal output.
18 MSKCLK I SYNC output control clock input.
19 XFMWP O Flash memory WP signal output.
20 XFMSE O Flash memory SE signal output.
21 BEEP O BEEP signal output (2.4kHz).
22 LIGHT O LCD back lignt control output.
23 – 26 COMO 0–3 O LCD common signal output.
27 BIAS – Connect to VCC (LCD BIAS).
28 – 30 VLC 0 – 2 – LCD drive power supply.
31 VSS0 – Ground.
32 – 61 S0 – S29 O LCD segment signal output.
62 XVORSW I VOR switch input.
63 XVORIN I VOR signal input.
64 XTEST I Test terminal.
65 XDSPDEN O DSP registor control I/F enable signal output.
66 LEDREC O REC LED (red) ON/OFF output.
67 LEDPB O PLAY LED (green) ON/OFF output.
68 AMPPOW O Power down control output for IC108.
69 SPOWER O IC101 and analog power supply control output.
70 RTCCE O Real time colck CE signal output.
71 XPDRST O Reset signal output for IC101.
72 DSPIS I Serial data input from IC101.
73 DSPIR O Playback serial data output for IC101.
74 XBLCK O DSP bit clock signal output.
75 RTCDI I Real time colck data input.
76 RTCDO O RTC data and DSP registor contrl data output.
77 RTCCLK O RTC I/F data and DSP registor control clock output.
78 IC – Ground.
79 X2 O System clock output (5MHz).
80 X1 I System clock input (5MHz).

– 8 –
Pin No. Pin name I/O Description
81 VDD1 – Power supply terminal.
82 XT1 I Sub clock input.
83 XT2 I Sub clock turn over input.
84 XRESET I Reset signal input.
85 PCLINK I PC link connection detect input.
86 WAKEUP I WAKE UP signal input.
87 RTCINT I Real time clock (2Hz) signal input.
88 FLMPOW O Flash memory and IC707 power ON/OFF.
89 LPMODE O LPF switch control output.
90 LMUTE O Line mute ON/OFF signal output.
91 – 98 FMIO 0 – 7 I/O Data bus.
99 AVSS – A/D converter ground.
100 BATT I Power supply voltage detect input.

– 9 – – 10 –
ICD-R100PC
• Signal path.
F: PLAY
L: REC
4-2. BLOCK DIAGRAMS

– 11 – – 12 –
ICD-R100PC
4-3. PRINTED WIRING BOARDS (MAIN SECTION)
D501 F-5
IC101 C-6
IC102 C-5
IC103 B-2
IC104 C-2
IC105 D-2
IC106 C-6
IC107 D-6
IC108 G-2
IC109 B-6
IC502 G-5
IC503 E-5
IC504 B-5
IC506 H-5
IC705 F-6
IC707 E-2
IC708 E-2
IC709 D-3
IC710 C-2
IC777 D-6
Q101 G-5
Q102 H-5
Q103 B-3
Q105 F-2
Q108 B-5
Q109 F-2
Q110 D-2
Q502 B-3
Q704 D-3
Q777 D-2
Ref.No. Location
rSemiconductor
Location
Note:
•X: parts extracted from the component side.
•®:Through hole.
•b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
1 2 3 4 5 6 7 8 910
A
B
C
D
E
F
G
H
C155
C156
IC104
IC708
C149
C128
C508
FB106
IC105
IC108
C126
C127
C131
C717
C145
C144
C143
C142
C116
C112
C506
C108
C105
C148
C109
C125
C114
Q103
R724
R514
R510
R134
R111
R140
R135
R727
R157
R105
R104
R102
R504
R131
R121
R122
R118
R138 R144
R143
R509
R110
R133
R145
R506
R156
R132
R139
R153
R103
R146
Q105
FB102
FB107
FB105
C140
FB104
C718
FB101
R154
C102
FB701
Q502
R163
C723
R164
C157
IC709
Q704
IC710
Q109
Q110
R137
R151
R758
R142
R750
R749
R751
C725
R732
IC707
C722
R166
R167
Q777
C161
C162
R756
R152
C139
R765
TP112
RB705 RB704
IC103
L503
1
4
5
8
1
45
8
1
4
5
8
1
5
10
16
17
20
25
30
32
33 35 40 45 48
49
50
55
60
64
5
4
1
3
13
4
5
1
4
58
12
3
02
11
(11)
1-673-293-
[MAIN BOARD]
(SIDE A)
SP101
SPEAKER
CN102
D501
C513
IC502
CN703
C111
C510
C505
C104
IC107
C710
C129
R108
C141
C133
MIC101
MIC
C152
FB503
C110
C103
C124
C147
C118
C512
R726
IC504
FB501
R511
C716
R113
R117
R112
R106
R120
IC102
R109
R116
R149
R148
R147
R512
R161
IC106
L501
Q102
Q101
IC503
R162
C502
R160
R107
C151
C106
C130
R155
C153
C154
IC101
IC109
C160
C134
C137
C107
C101
CN701
CN701
DIGITAL I/O
R515
IC705
C719
R733
C724
C509
IC777
R752
R753
R754
R755
R763
C730
R761
R764
R743
R171
RB701 RB702
Q108
C158
R725
IC506
R141
R136
R762
C146
C136
R150
1
5
10
15
20
25
26
30
35
40
45
50
15
610
1
5
10
15
1
5
10
16
17
20
25
30
32
14
5
8
54
123
123
45
12
3
123
45
1
2
34
5
123
45
1
2
34
5
1
3
2
[MAIN BOARD]
(SIDE B)
4
5
3
2
1
1-673-293-
1-673-294-
1-673-294-
DIGITAL BOARD
CN705
(Page 18)
DRY BATTERY
SIZE "AAA"
(IEC DESIGNATION LR03)
2PCS, 3V
S101
S714
RV101
J101
[JACK BOARD] (SIDE A)
[JACK BOARD] (SIDE B)
11
(11)
11
(11)
CN101
1
56
10
11
(11)
A
GDS
FB103
S101
MIC SENS
L H
S713
VOR
OFF ON
∑VOL
J102
EAR
MIC
(PLUG-IN POWER)
S714
PLAY SPEED
SLOW NORMAL FAST

– 13 – – 14 – – 16 –– 15 –
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•U: B+ Line.
• Power voltage is dc 3V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : REC
( ) : PLAY
• Voltages and current are taken with aVOM (Input imped-
ance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F: PLAY
L: REC
4-4. SCHEMATIC DIAGRAM (MAIN SECTION) ICD-R100PC
rRefer to page 21 for IC Block Diagrams.
1
2
3
IC503 4
IC102 3
IC102 4
VOLT/DIV : 1 V AC
TIME/DIV : 2 µsec
VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec
VOLT/DIV : 5 V AC
TIME/DIV : 20 µsec
4.1 Vp-p
91.4 kHz
3.5 Vp-p
REC 11 kHz
PLAY 13 kHz
1.7 Vp-
p
14kHz
rWaveforms

– 19 – – 20 –– 17 – – 18 –
4-5. PRINTED WIRING BOARDS (DIGITAL SECTION)
4-6. SCHEMATIC DIAGRAM (DIGITAL SECTION)
Note on PrintedWiring Boards:
Note:
•X: parts extracted from the component side.
•¢: internal component.
•®:Through hole.
•b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
D502 A-3
D503 B-1
D504 B-2
D701 E-2
IC501 C-4
IC505 A-2
IC701 E-2
IC702 F-1
IC703 F-2
IC704 C-5
IC706 E-5
Q501 A-2
Q503 A-2
Q701 F-5
Q702 F-6
Q703 F-1
Ref.No. Location
rSemiconductor
Location
rRefer to page 22 for IC Block Diagrams.
ICD-R100PC
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•¢: internal component.
•U: B+ Line.
• Power voltage is dc 3V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : REC
( ) : PLAY
• Voltages and current are taken with aVOM (Input imped-
ance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
1 2 3 4 5 6
A
B
C
D
E
F
G
A
MAIN BOARD
CN703
(Page 11)
11
(11)
S703
R742
CN705
IC706
IC501
C702
S704
C701
X701
Q701
IC704
R703
C708
R704
C721
R734
JC702
R501
C501
C711
R738
C704
C504
R741
JC701
S701
S711
R502
R740
C712
R723
R745
FB703
R730
C726
C727
R739
X702
Q702
1
5
610
1
5
10
15
20
25 26
30
35
40
45
50
1
5
10
15
20
25
263035404550
51
55
60
65
70
75
76 80 85 90 95 100
[DIGITAL BOARD] (SIDE B)
CN702
D503 D504
R744
IC505
D502
R503
R513
IC701
Q501
C715
IC702
R715
IC703
R720
Q503
Q703
D701
BP701
R728
R507
R711
R712
CN704
R713
S702
S712
R729
R721
R737
R731
R719
C709
R701
R508
R505
R722
R714
R747
FB702
R702
R766
1
3
2
16
1510152024
25 30 35 40 45 48
1
3
45
13
45
LCD BACK LIGHT 1
5
10
15
20
25
30
34
[DIGITAL BOARD] (SIDE A)
22
02
LCD101
LIQUID CRYSTAL DISPLAY
11
(11)
1-673-292-
1-673-292-
OPR
SWITCH UNIT
DISPLAY MENU STOP
”PLAY/STOP
=REVIEW/– +CUE/+
D502
S703
INDEX
S701
rREC/STOP
S711
PPAUSE
S702
FILE
S712
HOLD
ON
OFF
S704
ERASE
rWaveforms
1
IC704 &ª
2
3
4
5
VOLT/DIV : 0.5 V AC
TIME/DIV : 50 nsec
IC706 8
IC704 !∞
IC704 !§
IC704 *™
VOLT/DIV : 0.1 V AC
TIME/DIV : 10 µsec
VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec
VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec
VOLT/DIV : 0.2 V AC
TIME/DIV : 10 µsec
1.3 Vp-
p
5 MHz
438 mVp-
p
32.768 kHz
3.5 Vp-p
REC 11 kHz
PLAY 13 kHz
3.5 Vp-p
REC 11 kHz
PLAY 13 kHz
0.8 Vp-p
32.768 kHz

– 21 –
IC104 NJM2072M
IC102 XC25A08510MR
rIC Block Diagrams (MAIN SECTION)
IC101 MSM7590L-01TS-K
IC709 TC7S08FU (TE85R)
IR
PCMRO
PCMRI
ATT
ATT
PCM
ENCODER
ADPCM
ENCODER
REFERENCE
POWER SUPPLY
ADPCM
DECODER
CLOCK,
TIMING
GENERATOR
P/S
or
S/P
PCM
DECODER
BACK-GROUND
NOISE
GENERATOR
DTMF/
OTHERS TONE
GENERATOR
VOICE
DETECT
AIN1+
AIN1–
GSX1
AIN2
25
24
23
22
21
MCK
CPU
INTERFACE
DEN
20 EXCK
19 DIN
18 DOUT
17 VOXO
PCMSO
PCMSI
IS
28
27
26
BCLK
XSYNC
RSYNC
31
DG
32
30
29
3
SG 2
AG 1
4
5
GSX2 7
VFRO 8
PWI 9
AOUT– 10
AOUT+ 11
6
+
–
+
–
+
–
–1
SAO+ 12 +1
SAO– 13
VOXI 15
VDD 16
PDN/RESET 14
–1
CLKINVSS VDD
CLKOUT
PHASE
DETECTOR
1/N
COUNTER
L.P.F.
VCO
1/2
BUFFER
21 3
4
CE
51
2
3
4
8
7
6
5
GND
AMP OUT
GAIN CONT
INPUT VCC
OUTPUT2
OUTPUT1
RECOVERY
TIME CAP
15
24
3
IN B VCC
IN A
GND
OUT Y


– 22 –
IC503 XC6372C381PR
IC706 RS5C348A-E2
IC702 TC7S08FU (TE85R)
rIC Block Diagrams (DIGITAL SECTION)
NC
VOUT
CE
VSS
LX
2
1
3
4
5
VLX
LIMITER
PWM/PFM
CONTROL
OSC 100kHz
BUFFER
PHASE
COMPARATOR
REFERENCE
VOLTAGE
CHIP
ENABLE
SLOW
START
+
–
VDD
VDD
VDD
OSCIN
OSCOUT
CE
INTR
32KOUT
SCLK
SO
SI
VSS
32 kHz
OUTPUT
CONTROL COMPARATOR
W
COMPARATOR
D
ADDRESS
REGISTER
I/O
CONTROL
ADDRESS
DECODER
SHIFT
REGISTER
INTERRUPT
CONTROL
OSC
DETECT
VOLTAGE
DETECT
ALARM W REGISTER
(WEEK, MIN, HOUR)
ALARM D REGISTER
(MIN, HOUR)
DIV OSC
DIVIDER
CORRECTION
9
10
8
7
6
2
3
4
5
1
TIMER COUNTER
SEC, MIN, HOUR, WEEK,
DAY, MONTH, YEAR
15
24
3
IN B VCC
IN A
GND
OUT Y


– 23 –
SECTION 5
EXPLODEDVIEWS
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference
number in the exploded views are not
supplied.
• Aaccessories and packing materials are given
in the last of this parts list.
13
12
7
6
18
20
21
17
3
16
16
15
9
8
8
14
10
11
19
2
2
1
SP101
not supplied
22
5
15
23
4
Note: Not using a screw (10mm)
of No.22 for this place.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-217-035-01 CAP (PC)
2 3-318-203-91 SCREW (B1.7X9), TAPPING
3 4-217-034-01 LID, BATTERY CASE
4 X-4951-074-1 CASE ASSY
5 4-220-198-01 CUSHION (BATT)
6 4-221-482-01 SPACER (CLIP)
7 X-4951-795-1 CLIP ASSY
8 3-349-859-41 WASHER
9 4-217-036-01 CLIP
10 4-217-864-01 SHAFT (CLIP)
11 4-221-241-01 WASHER (P)
12 4-217-037-01 SPRING (CLIP)
13 X-4951-072-1 LID ASSY, UPPER
14 3-375-114-41 SCREW
15 4-217-032-01 BRACKET (SPEAKER)
16 4-221-238-01 SHEET (BUTTON)
17 4-220-916-01 SHEET (LED)
18 4-221-239-01 SHEET (STOP)
19 4-221-237-01 CUSHION (LCD)
20 4-221-236-01 CUSHION (PC)
21 4-221-616-01 SPACER (TERMINAL)
22 3-334-565-01 SCREW (B1.7X10), TAPPING
23 3-318-382-71 SCREW (1.7X4), TAPPING
SP101 1-505-854-11 SPEAKER (2.8cm)
5-1. CASE SECTION
Note: Not using a screw (10mm)
of No.22 for this place.

– 24 –
51 A-3321-888-A MAIN BOARD, COMPLETE
52 4-221-243-01 CUSHION, RUBBER
53 4-220-920-01 SPACER (P2)
54 4-220-922-11 SHEET (F)
55 4-217-039-01 TERMINAL (-), BATTERY
56 4-217-038-01 TERMINAL (+), BATTERY
57 4-217-040-01 CAP (TERMINAL)
58 4-221-344-01 SPACER (FLASH)
59 A-3321-891-A DIGITAL BOARD, COMPLETE
60 4-218-348-01 SHEET (MICROPHONE)
61 4-221-241-11 WASHER (P)
62 4-220-924-01 SHEET (H)
63 4-220-200-01 SHEET (MICROPHONE), ADHESIVE
64 4-219-466-01 SPACER (P)
*65 1-673-294-11 JACK BOARD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
66 4-220-918-01 SPACER (HOLDER LR)
67 3-016-413-21 SHEET (SW)
68 1-418-318-11 UNIT, SWITCH
69 4-217-031-01 HOLDER, LCD
70 4-220-917-01 SPACER (HOLDER 2)
71 4-220-199-01 SHEET (HOLDER)
72 4-220-919-01 SHEET (HOLDER LR)
73 4-220-921-01 SHEET (SW)
74 4-220-141-01 SHEET (BL)
75 4-220-197-01 SPACER (HOLDER)
76 1-694-521-11 CONDUCTIVE BOARD, CONECTION
77 4-218-499-01 PLATE, LIGHT GUIDE
LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL
MIC101 1-542-384-11 MICROPHONE, ELECTRET CONDENSER
5-2. MAIN BOARD SECTION
63
51
MIC101
LCD101
52
54
65
53
55
57
56
58
75
77
71
69
59
61
60
64
76
74
73
66
72
68
67
70
62

– 25 –
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example :
uA.... : µA.... , uPA.... : µPA....
uPB.... : µPB.... , uPC.... : µPC....
uPD.... : µPD....
• CAPACITORS
uF : µF
• COILS
uH : µH
When indicating parts by reference num-
ber, please include the board.
SECTION 6
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-3321-891-A DIGITAL BOARD, COMPLETE
**********************
1-418-318-11 UNIT,SWITCH
1-694-521-11 CONDUCTIVE BOARD, CONECTION
4-217-031-01 HOLDER, LCD
4-218-499-01 PLATE, LIGHT GUIDE
4-220-141-01 SHEET (BL)
4-220-197-01 SPACER (HOLDER)
4-220-199-01 SHEET (HOLDER)
4-220-917-01 SPACER (HOLDER 2)
4-220-918-01 SPACER (HOLDER LR)
4-220-919-01 SHEET (HOLDER LR)
4-220-921-01 SHEET (SW)
4-220-922-11 SHEET (F)
4-220-924-01 SHEET (H)
4-221-344-01 SPACER (FLASH)
<CAPACITOR>
C501 1-107-826-11 CERAMIC CHIP 0.1uF 16V
C504 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C701 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C702 1-104-913-91 TANTAL. CHIP 10uF 20% 16V
C704 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C708 1-113-988-11 TANTAL. CHIP 68uF 20% 4V
C709 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C711 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C712 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C715 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C721 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C726 1-162-921-91 CERAMIC CHIP 33PF
C727 1-162-921-91 CERAMIC CHIP 33PF
<CONNECTOR>
*CN704 1-785-876-21 CONNECTOR, FPC
*CN705 1-785-874-21 PLUG, BOARD TO BOARD 50P
<DIODE>
D502 8-719-073-33 LED CL-165HR/YG-D-T (OPR)
D503 8-719-070-68 DIODE CL-220YG-C-TS (LCD BACK LIGHT)
D504 8-719-070-68 DIODE CL-220YG-C-TS (LCD BACK LIGHT)
D701 8-719-016-74 DIODE 1SS352
<FERRITEBEAD>
FB702 1-414-921-11 INDUCTOR CHIP
FB703 1-414-921-11 INDUCTOR CHIP
<JUMPERREGISTOR>
JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
JC702 1-216-864-11 METAL CHIP 0 5% 1/16W
<IC>
IC501 8-759-333-42 IC XC61AN3002MR
IC505 8-759-497-27 IC XC62AP2102MR
IC701 8-759-583-36 IC KM29U128T
IC702 8-759-058-62 IC TC7S08FU(TE85R)
IC703 8-759-058-58 IC TC7S04FU(TE85R)
IC704 8-759-579-98 IC uPD780308GC-113-8EU
IC706 8-759-560-17 IC RS5C348A-E2
<LIQUIDCRYSTALDISPLAY PANEL>
LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL
<TRANSISTOR>
Q501 8-729-426-25 TRANSISTOR XP1212
Q503 8-729-402-32 TRANSISTOR 2SD1819A-R
Q701 8-729-037-74 TRANSISTOR UN9213J-(TX).SO
Q702 8-729-420-24 TRANSISTOR 2SB1218A-QRS
Q703 8-729-420-24 TRANSISTOR 2SB1218A-QRS
<RESISTOR>
R501 1-216-845-11 METAL CHIP 100K 5% 1/16W
R502 1-216-821-11 METAL CHIP 1K 5% 1/16W
R503 1-216-817-11 METAL CHIP 470 5% 1/16W
R505 1-216-821-11 METAL CHIP 1K 5% 1/16W
R507 1-216-833-91 RES,CHIP 10K 5% 1/16W
R508 1-216-793-11 RES,CHIP 5 5% 1/16W
R513 1-216-809-11 METAL CHIP 100 5% 1/16W
R701 1-216-845-11 METAL CHIP 100K 5% 1/16W
R702 1-216-845-11 METAL CHIP 100K 5% 1/16W
R703 1-216-857-11 METAL CHIP 1M 5% 1/16W
R704 1-216-854-11 METAL CHIP 560K 5% 1/16W
R711 1-216-849-11 METAL CHIP 220K 5% 1/16W
R712 1-216-849-11 METAL CHIP 220K 5% 1/16W
R713 1-216-857-11 METAL CHIP 1M 5% 1/16W
DIGITAL

– 26 –
R714 1-216-854-11 METAL CHIP 560K 5% 1/16W
R715 1-216-849-11 METAL CHIP 220K 5% 1/16W
R719 1-218-871-11 RES,CHIP 10K 0.50% 1/16W
R720 1-218-875-11 RES,CHIP 15K 0.50% 1/16W
R721 1-216-855-11 METAL CHIP 680K 5% 1/16W
R722 1-216-821-11 METAL CHIP 1K 5% 1/16W
R723 1-216-821-11 METAL CHIP 1K 5% 1/16W
R728 1-216-831-91 METAL CHIP 10K 5% 1/16W
R729 1-218-879-11 RES,CHIP 22K 0.50% 1/16W
R730 1-218-887-11 METAL CHIP 47K 0.50% 1/16W
R731 1-216-855-11 METAL CHIP 680K 5% 1/16W
R734 1-216-833-91 RES,CHIP 10K 5% 1/16W
R737 1-216-853-11 METAL CHIP 470K 5% 1/16W
R738 1-216-833-91 RES,CHIP 10K 5% 1/16W
R739 1-216-833-91 RES,CHIP 10K 5% 1/16W
R740 1-216-833-91 RES,CHIP 10K 5% 1/16W
R741 1-216-833-91 RES,CHIP 10K 5% 1/16W
R742 1-216-845-11 METAL CHIP 100K 5% 1/16W
R744 1-216-853-11 METAL CHIP 470K 5% 1/16W
R745 1-216-821-11 METAL CHIP 1K 5% 1/16W
R747 1-216-845-11 METAL CHIP 100K 5% 1/16W
R764 1-216-845-11 METAL CHIP 100K 5% 1/16W
R766 1-216-857-11 METAL CHIP 1M 5% 1/16W
<SWITCH>
S701 1-771-585-11 SWITCH, PUSH (1 KEY) (rREC/STOP)
S702 1-762-366-11 SWITCH, TACTILE (FILE)
S703 1-762-366-11 SWITCH, TACTILE (INDEX)
S704 1-771-585-11 SWITCH, PUSH (1 KEY) (ERASE)
S711 1-771-248-11 SWITCH, TACTILE (PPAUSE)
S712 1-572-922-11 SWITCH, SLIDE (HOLD)
<VIBRATOR>
*X701 1-767-994-22 VIBRATOR, CRYSTAL (32.768kHz)
X702 1-767-144-21 VIBRATOR, CERAMIC (5MHz)
**************************************************************
*1-673-294-11 JACK BOARD
***********
<CONNECTOR>
*CN101 1-785-873-21 CONNECTOR, BOARD TO BOARD 10P
<JACK>
J101 1-784-848-21 JACK (MIC (PLUG-IN POWER))
J102 1-785-869-21 JACK (EARPHONE)
**************************************************************
A-3321-888-A MAIN BOARD, COMPLETE
*********************
<CAPACITOR>
C101 1-104-913-11 TANTAL. CHIP 10uF 20% 10V
C102 1-115-156-11 CERAMIC CHIP 1uF 10V
C103 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C104 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C105 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C106 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C107 1-113-600-11 TANTAL. CHIP 2.2uF 20% 6.3V
C108 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C109 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C110 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C111 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C112 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C114 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C116 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C118 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C124 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C125 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C126 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C127 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C128 1-125-926-91 TANTAL. CHIP 4.7uF 20% 6.3V
C129 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C130 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C131 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C133 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C134 1-109-847-11 TANTAL. CHIP 0.47uF 20% 16V
C136 1-117-370-11 CERAMIC CHIP 10uF 10V
C137 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C139 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C140 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C141 1-164-357-11 CERAMIC CHIP 1000PF 5% 50V
C142 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C143 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C144 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C145 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C146 1-164-360-11 CERAMIC CHIP 0.1uF 16V
*C147 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C148 1-115-156-11 CERAMIC CHIP 1uF 10V
C149 1-109-847-11 TANTAL. CHIP 0.47uF 20% 16V
C151 1-117-370-11 CERAMIC CHIP 10uF 10V
C152 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C153 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C154 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
C155 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C156 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C157 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C158 1-113-682-11 TANTAL. CHIP 33uF 20% 10V
C160 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C161 1-162-957-91 CERAMIC CHIP 220PF 5% 50V
C162 1-164-471-11 CERAMIC CHIP 680PF 5% 50V
C502 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C505 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C506 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C508 1-117-370-11 CERAMIC CHIP 10uF 10V
C509 1-128-829-91 TANTAL. CHIP 220uF 20% 6.3V
C510 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C512 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C513 1-117-370-11 CERAMIC CHIP 10uF 10V
C710 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C716 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C717 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C718 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
DIGITAL JACK MAIN

– 27 –
C719 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C722 1-104-851-91 TANTAL. CHIP 10uF 20% 10V
*C723 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
*C724 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C725 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C730 1-107-726-91 CERAMIC CHIP 0.01uF 10% 16V
<CONNECTOR>
*CN102 1-785-872-21 PLUG, BOARD TO BOARD 10P
CN701 1-785-871-21 CONNECTOR, PC LINK (DIGITAL I/O)
*CN703 1-785-875-21 CONNECTOR, BOARD TO BOARD 50P
<DIODE>
D501 8-719-073-35 DIODE RB551V-30TE-17
<FERRITEBEAD>
FB101 1-414-593-21 FERRITE BEAD INDUCTOR
FB102 1-414-593-21 FERRITE BEAD INDUCTOR
FB103 1-414-593-21 FERRITE BEAD INDUCTOR
FB104 1-414-593-21 FERRITE BEAD INDUCTOR
FB105 1-414-593-21 FERRITE BEAD INDUCTOR
FB106 1-414-593-21 FERRITE BEAD INDUCTOR
FB107 1-414-593-21 FERRITE BEAD INDUCTOR
FB501 1-414-921-11 INDUCTOR 2.2uH
FB503 1-414-921-11 INDUCTOR 2.2uH
FB701 1-414-921-11 INDUCTOR 2.2uH
<IC>
IC101 8-759-567-09 IC MSM7590L-01TS-K
IC102 8-759-567-10 IC XC25A08510MR
IC103 8-759-574-34 IC LMV358MMX
IC104 8-759-701-51 IC NJM2072M
IC105 8-759-582-03 IC NJM2149V-TE2
IC106 8-759-082-60 IC TC7S66FU
IC107 8-759-358-47 IC NJM2115V(TE2)
IC108 8-759-582-03 IC NJM2149V-TE2
IC109 8-759-586-57 IC AN6123MS
IC502 8-759-583-76 IC XC62GR3522MR
IC503 8-759-582-02 IC XC6372C381PR
IC504 8-759-592-24 IC XC61AN1502MR
IC506 8-759-583-76 IC XC62GR3522MR
IC705 8-759-595-14 IC XC61A2202MR
IC707 8-759-592-25 IC CXD9519TQ
IC708 8-759-583-76 IC XC62GR3522MR
IC709 8-759-058-62 IC TC7S08FU(TE85R)
IC710 8-759-333-42 IC XC61AN3002MR
IC777 8-759-710-84 IC NJM2406F-TE2
<COIL>
L501 1-469-395-21 INDUCTOR
L503 1-414-752-11 INDUCTOR 2.2uH
<TRANSISTOR>
Q101 8-729-429-44 TRANSISTOR XP1501
Q102 8-729-037-63 TRANSISTOR UN9115J-(TX).SO
Q103 8-729-429-50 TRANSISTOR XP4312
Q105 8-729-039-57 TRANSISTOR DTC363EKT146
Q108 8-729-048-59 TRANSISTOR XC161A1265PR
Q109 8-729-037-76 TRANSISTOR UN9215J-(TX).SO
Q110 8-729-037-76 TRANSISTOR UN9215J-(TX).SO
Q502 8-729-427-74 TRANSISTOR XP4601
Q704 8-729-037-63 TRANSISTOR UN9115J-(TX).SO
Q777 8-729-037-63 TRANSISTOR UN9115J-(TX).SO
<RESISTOR>
R102 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R103 1-216-815-11 METAL CHIP 330 5% 1/16W
R104 1-216-839-11 METAL CHIP 33K 5% 1/16W
R105 1-216-833-91 RES,CHIP 10K 5% 1/16W
R106 1-216-821-11 METAL CHIP 1K 5% 1/16W
R107 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R108 1-216-821-11 METAL CHIP 1K 5% 1/16W
R109 1-216-841-11 METAL CHIP 47K 5% 1/16W
R110 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R111 1-216-841-11 METAL CHIP 47K 5% 1/16W
R112 1-216-841-11 METAL CHIP 47K 5% 1/16W
R113 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R116 1-216-833-91 RES,CHIP 10K 5% 1/16W
R117 1-216-833-91 RES,CHIP 10K 5% 1/16W
R118 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R120 1-216-845-11 METAL CHIP 100K 5% 1/16W
R121 1-216-845-11 METAL CHIP 100K 5% 1/16W
R122 1-209-926-11 METAL CHIP 36K 5% 1/16W
R131 1-216-835-11 METAL CHIP 15K 5% 1/16W
R132 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R133 1-216-833-91 RES,CHIP 10K 5% 1/16W
R134 1-216-841-11 METAL CHIP 47K 5% 1/16W
R135 1-216-841-11 METAL CHIP 47K 5% 1/16W
R136 1-216-837-11 METAL CHIP 22K 5% 1/16W
R137 1-216-849-11 METAL CHIP 220K 5% 1/16W
R138 1-216-833-91 RES,CHIP 10K 5% 1/16W
R139 1-216-839-11 METAL CHIP 33K 5% 1/16W
R140 1-216-845-11 METAL CHIP 100K 5% 1/16W
R141 1-216-837-11 METAL CHIP 22K 5% 1/16W
R142 1-216-853-11 METAL CHIP 470K 5% 1/16W
R143 1-209-926-11 METAL CHIP 36K 5% 1/16W
R144 1-218-292-11 RES,CHIP 20K 5% 1/16W
R145 1-216-833-91 RES,CHIP 10K 5% 1/16W
R146 1-218-292-11 RES,CHIP 20K 5% 1/16W
R147 1-216-817-11 METAL CHIP 470 5% 1/16W
R148 1-216-824-11 METAL CHIP 1.8K 5% 1/16W
R149 1-216-837-11 METAL CHIP 22K 5% 1/16W
R150 1-216-837-11 METAL CHIP 22K 5% 1/16W
R151 1-216-853-11 METAL CHIP 470K 5% 1/16W
R152 1-216-849-11 METAL CHIP 220K 5% 1/16W
R153 1-216-833-91 RES,CHIP 10K 5% 1/16W
R154 1-216-845-11 METAL CHIP 100K 5% 1/16W
R155 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R156 1-216-797-11 METAL CHIP 10 5% 1/16W
R157 1-216-797-11 METAL CHIP 10 5% 1/16W
R160 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R161 1-216-821-11 METAL CHIP 1K 5% 1/16W
R162 1-216-799-11 METAL CHIP 15 5% 1/16W
R163 1-216-835-91 RES,CHIP 15K 5% 1/16W
R164 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R166 1-216-857-11 METAL CHIP 1M 5% 1/16W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAIN

– 28 –
ICD-R100PC
9-927-123-11 Sony Corporation
Personal Audio Company 99E0266-1
Printed in Japan © 1999.5
Published by General Engineering Dept.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R167 1-216-833-91 RES,CHIP 10K 5% 1/16W
R171 1-216-813-91 METAL CHIP 220 5% 1/16W
R504 1-216-853-11 METAL CHIP 470K 5% 1/16W
R506 1-216-853-11 METAL CHIP 470K 5% 1/16W
R509 1-216-857-11 METAL CHIP 1M 5% 1/16W
R510 1-216-849-11 METAL CHIP 220K 5% 1/16W
R511 1-218-895-11 RES,CHIP 100K 0.50% 1/16W
R512 1-218-895-11 RES,CHIP 100K 0.50% 1/16W
R514 1-216-845-11 METAL CHIP 100K 5% 1/16W
R515 1-216-864-11 METAL CHIP 0 5% 1/16W
R724 1-216-855-11 METAL CHIP 680K 5% 1/16W
R725 1-216-821-11 METAL CHIP 1K 5% 1/16W
R726 1-216-849-11 METAL CHIP 220K 5% 1/16W
R727 1-216-849-11 METAL CHIP 220K 5% 1/16W
R733 1-216-845-11 METAL CHIP 100K 5% 1/16W
R743 1-216-833-91 RES,CHIP 10K 5% 1/16W
R732 1-216-845-11 METAL CHIP 100K 5% 1/16W
R749 1-216-845-11 METAL CHIP 100K 5% 1/16W
R750 1-216-833-91 RES,CHIP 10K 5% 1/16W
R751 1-216-845-11 METAL CHIP 100K 5% 1/16W
R752 1-216-833-91 RES,CHIP 10K 5% 1/16W
R753 1-216-833-91 RES,CHIP 10K 5% 1/16W
R754 1-216-813-91 METAL CHIP 220 5% 1/16W
R755 1-216-813-91 METAL CHIP 220 5% 1/16W
R756 1-216-837-11 METAL CHIP 22K 5% 1/16W
R758 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R761 1-216-821-11 METAL CHIP 1K 5% 1/16W
R762 1-216-841-11 METAL CHIP 47K 5% 1/16W
R763 1-216-833-91 RES,CHIP 10K 5% 1/16W
R764 1-216-845-11 METAL CHIP 100K 5% 1/16W
R765 1-216-849-11 METAL CHIP 220K 5% 1/16W
<COMPOSITION CIRCUIT BLOCK >
RB701 1-233-957-11 RES, NETWORK (CHIP TYPE) 220
RB702 1-233-957-11 RES, NETWORK (CHIP TYPE) 220
RB704 1-233-961-21 RES, NETWORK (CHIP TYPE) 1K
RB705 1-233-961-21 RES, NETWORK (CHIP TYPE) 1K
<VARIABLE RESISTOR >
RV101 1-225-502-41 RES, VAR, CARBON 10K/10K(∑VOL)
<SWITCH>
S101 1-572-922-11 SWITCH, SLIDE (MIC SENS)
S713 1-572-922-11 SWITCH, SLIDE (VOR)
S714 1-692-605-31 SWITCH, SLIDE (PLAY SPEED)
**************************************************************
MISCELLANEOUS
***************
11 1-418-318-11 UNIT, SWITCH
14 1-694-521-11 CONDUCTIVE BOARD, CONECTION
LCD101 1-803-522-11 DISPLAY PANEL, LIQUID CRYSTAL
MIC101 1-542-384-11 MICROPHONE, ELECTRET CONDENSER
SP101 1-505-854-11 SPEAKER (2.8cm)
**************************************************************
MAIN
ACCESSORIES&PACKING MATERIALS
*******************************
1-790-857-11 CABLE, CONNECTION
3-866-532-11 MANUAL, INSTRUCTION (ENGLISH) (US)
3-866-532-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(Canadian,AEP)
3-866-532-31 MANUAL, INSTRUCTION (SPANISH,
PORTUGUESE) (AEP)
3-866-532-41 MANUAL, INSTRUCTION (DANISH,DUTCH)
(AEP)
3-866-532-51 MANUAL, INSTRUCTION (SWEDISH,ITALIAN)
(AEP)
3-866-581-11 MANUAL, INSTRUCTION (ENGLISH) (US)
3-866-581-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(Canadian,AEP)
3-866-581-31 MANUAL, INSTRUCTION (SPANISH,
PORTUGUESE) (AEP)
3-866-581-41 MANUAL, INSTRUCTION (DANISH,DUTCH)
(AEP)
3-866-581-51 MANUAL, INSTRUCTION (SWEDISH,ITALIAN)
(AEP)
4-217-041-01 CASE, CARRYING
4-220-196-01 FLOPPY (EG), SOFT (No.1)
4-220-196-11 FLOPPY (EG), SOFT (No.2)
4-220-196-21 FLOPPY (EG), SOFT (No.3)