Sorelle 68 NICKI User manual

;J '-C Ir / 'IT
BySorelle -A Division of caT"lntemational,Inc.
46 Whelan Road, East Rutherford, NJ 07073 U.S.A.
Sorel Ie
Tel, 201/5311919 Fax,201/5311920
RE/o,D !\LL I~JSl f)UCflOr JS BEFORE USE OF THE CHNJGII~l~ H\BLE OR CH/-\NGIf.JG PAD
~WARNING
FALL HAZARD -'TO PREVENT DEATI-i OR SERIOJS INJUR~
AUNA'VS KEEP Q-tILD wrn-oN ARMS REAO-t
• KEEP INSTRUCTIONS FOR RmJRE USE.
• USE ONLY THE PAD PROVIDED BY THE MANUFACTURER.
•• DO NOT USE THE CHANGE TABLE IF IT IS DAMAGED OR BROKEN. ASK YOUR DEALER OR
CONTACT MANUFACTURER FOR REPLACEMENT PARTS AND INSTRUCTIONAL liTERATURE
IF NEEDED.
• DO NOT SUBSTI1lJJ"E PARTS.
• IF REFINISHING, USE A NON-TOXIC FINISH SPEOFIED FOR CHILDREN'S PRODUCTS.
• CHECK FASTERNERS PERIODICALL'1, DO NOT OVER TIGHTEN. THIS MAY CAUSE DISTORTION
OR BREAKAGE. -
'.
WHEN CHILD REACHES A MAXIMUM WEIGHT OF 30 LBS.,
THE CHANGING TABLE SHALL NO LONGER BE USED

68 NICKI CHANGING TABLE INSTRUCTION PAGE 2
Sorel Ie
ASSEMBLY INSTRUCTIONS
PARTS LIST
No..Qty Description
A 1
Right Headboard
B 1
Left Headboard
C 2 Non-grooved Ralls
D 6
Grooved Rails
E 1 Top Shelfwith holes
F 2 Shelves
G 1 Drawer Front
H 1
Drawer Back
I 1 Drawer Right
J 1 Drawer Left
K 1 Drawer Bottom
L 16 85mm (33/8") Bolts (12mm head)
• M 16 Barrel Nuts
N 1 Changing Pad
o 2 Mini Blocks
p 2 Screws
Q 2 Screws
R 4 Castens (2 - Safety Locking Mechanism)
S 2
16mm () /8 j Bolts
T 2 washers
U 2 Nuts
V 1 Safety Harness
W 1 Allen Key *THIS PRODUCT MAY BE DIFFERENT FROM THE INSTRUCTION SHEET SHOWN'
1x 1x
@
~ ['[email protected]
1X
)
~ 16x
~
ToOl required
Impor1llnt: In order to property .... mbII the changing t8b1e, carry out the operationl In order lpecifled. Failure to allamble the changing table in the manner
recommended could make the changing table haZ8Rloul

Sorel Ie
68 NICKI CHANGING TABLE INSTRUCTION
PAGE 3
ASSEMBLY INSTRUCTIONS
LEFT HEADBOARD AND RAilS
•
ASSEMBLY
..............
.... \
...... \.
.,- ....
.,- ....
::,,:~
.. ~
.. ..
::::::::: ..
( Fully tighten)
.,.-....
_
SHELVES
ASSEMBLY
Step 1
Lay the headboard on the floor, rails up.
NOTE, make sure that the top shelf with the two holes
is inserted into the top rails.
Step 2
Slide the shelf through the grooves in the
headboard.
Repeat with the two remaining
shelves.
'.

Step 2
cC: .
~--. ·0,
step 4
2x
68 NICKI CHANGING TABLE INSTRUCTION
PAGE 4
SoreIIe
ASSEMBLY INSTRUCTIONS
...- ..
....
RIGHT HEADBOARD
' ..
. '.
".
•
ASSEMBLY
'"
' .
.....
......
:~ .
f -.\
.. ,:
..........
....
.......
...........
...........
( Fully tighten)
DRAWER
• • 1II ASSEMBLY
Step 1
@
Step 3

II
Sorel Ie
68 NICKI CHANGING TABLE INSTRUCTION
PAGE 5
ASSEMBLY INSTRUCTIONS
INSERT
DRAWER
Evenly slide the drawer along the
guide rails beneath the top
shetf .
.. SAFETY HARNESS
... ASSEMBLY
Step 1
To attach the aafety hame .. , place the safety harness (Part .V")
on the top shelf and align the hole on the safety hamess end with
the hole on the top shelf
Step 2
Insert
the bolt (Part ·S·) through awasher
(Part ·r), the hamess hole and the top shelf
hole.
Step 3
Secure with a nut (Part ·U·) on the underside
of
the top shelf.
Step 4
Repeat the process to attach the other side
of the hamess to the top shelf.
Step 5
Place changing pad on top of safety hame ...
SAFETY HARNESS/RESTRANT SYSTEM USE
1. Place the infant on the changing table foam pad
2. Position the safety harness overthe middle of the
infant's torso and insert the buckled ends into each
other until they lock shut with a click.
3. Gently pull the loose end of the safety to lightly snug
the safety harness around the infant. ••
'.
& WARNING
FALL HAZARD - ALWAYS KEEP OiILD WITHIN ARM'S REAOi

Sorel Ie
68 NICKI CHANGING TABLE INSTRUCTION
PAGE 6
ASSEMBLY INSTRUCTIONS
_CASTERS
"ASSEMBLY
II CARE AND MAINTENANCE
o ALWAYS STORE THE CHANGING TABLE IN A CLEAN AND DRY PLACE. .
o TO CLEAN YOUR CHANGING TABLE, USE A SOFT DAMP CLOTH WITH A SMALL AMOUNT OF MILD SOAP,
WIPE IMMEDIATELY WITH A DRY CLOTH.
o DO NOT USE ABRASIVES OR DETERGENT ON CHANGING TABLE SURFACES.
o OCCASIONAL USE OF FURNITURE POLISH WILL MANTAIN THE FINISH OF YOUR CHANGING TABLE.
o REGULARLY CHECK ALL SCREWS AND FITTINGS TO ENSURE THEY ARE TIGHT.
o THE IDEAL BAlANCE IS TO MAINTAIN THE TEMPERATURE AROUND 21·C (70·F) AND THE RELATIVE
HUMIDITY AT 40% TO PREVENT WARPING OR SPUTTING.
'.