Sorelle Torino Crib User manual

Made in JW Vietnam
Torino Crib
Assembly Instruction
Important Information:
Read all instructions BEFOREassembling crib.
KEEP INSTRUTIONS FOR FUTURE USE.

475 #Torino crib assembly instructions ( JW )
Page 2
WARNING -
R ruc bef r r b. KEEP INSTRUCTIONS FOR FUTURE USE. DO NOT
USE R L L WED.
ef re each u a e ra e b y, pec cr bf rda aed hardware, e , par r
harp ed e . DO NOT uecrb a ypar are rbr ke .A ky ur dea er rwr e&T
Ie a /S re ef r rep ace epar a d ruc aera ure feeded. DO NOT ub u e
par .
Treduce he kf SIDS pe re edhe hy f p aced he r back eep,
ueherw eadv ed by ur p a .
W r h . , r b
c b c ver r bed.
c r r c r r rap a r d. a
w. DO NOT c c rd , r a c bec w r
d’ rb.
S r c r a DO NOT c r r d’ ,
h r c rd .DO NOT p r v r a r y .
I r , p f re ’ r duc .
Whe dab epu a p e er we p a dre bu per
pad ,ar y a d her bjec a d erve a ep f r b u .
NEVER a r c v bec e
fca
DO NOT wa a r r b.
r b
r f r f y b k r r y, aever c p r per
r c bef r y r b. Mak r a b
ar h
CRIB WARNINGS
Failure to follow these warnings and assembly instructions
could result in serious injury or death.
!
WARNING-
WARNING-
Infants can suffocate on soft bedding. Never add a pillow or comforter
Never place additional padding under an infant.
!
Infants can suffocate in gaps between crib sides and a mattress that is
too small.
!
WARNING:
SENTRAPMENT/ TRANGULATION HAZARD
FALLHAZARD
CAUTION : ANYMATTRESSUSEDINTHISCRIBMUST
BEAT LEAST 271/4” (69CM)x515/8”(131 CM) WITH
ATHICKNESSNOT EXCEEDING 6”(15CM).
DO NOT
Follow warnings on all products in a crib
SORELLE

Important: In order to properly assemble the crib, carry out the operations in order specified. Failure to assemble the crib in the manner recommended could
make the crib hazardous.
475# Torino Crib assembly instructions ( JW ) SORELLE
(a) M6 x 70 mm Bolts ( 8 pcs)
(b) M6 x 55 mm Bolts ( 4 pcs)
(c) Barrel Nut (8 pcs)
(d) M5 x 32mm Bolts (8 pcs)
(e) Wing Nut (8 pcs)
(B) Right End
(E) Mattress Support Bar
(C) Foot Board
(D) Head Board
(A) Left End
(1 pcs)
(1 pcs)
)scp1(
)scp1(
( 2 pcs)
(G) Mattress Support
(1 pcs)
( j ) Allen Key (1 pcs)
( h ) Washer ( 18 pcs)
( i ) Lock Washer ( 26 pcs)
Figure 1
3
Step 1
Model shown is example only.
Style may vary.
Use 8 pcs Bolt (a) with 8 pcs Washers(h)&Lock Washers(i)
and Barrel Nuts (c) attach Mattress Support Bar (E)
to Side Panel (A&B).As shown in Figure 1.
Tool required
Herramienta necesaria
(A)
(A)
(B)
(B)
(c)
(E)
(E)
(E)
(E)
(a)
(h)
(i)
( f ) M6 x 35 mm Bolts ( 6 pcs)

4
Step 3
Figure 2
This crib has a high position setup on
mattress support (G) for use during
your baby’s first months. As soon as
your baby starts to sit up or pull up,
you must use the lowest mattress level.
G
d
i
e
Tool required
Herramienta necesaria
SORELLE
Model shown is example only.
Style may vary.
Use 4 pcs Bolt (d) & 4 pcs Wing Nut (e) & 4pcs Lock Washers (i)
Step 2
attach Mattress Support (G) to Mattress Support Bar(E).
As shown in Figure 3.
Tool required
Herramienta necesaria
Model shown is example only.
Style may vary.
475# Torino Crib assembly instructions ( JW )
Figure 3
(A)
(B)
(E)
(G)
(E)
d
ie

475# Torino Crib assembly instructions ( JW )
Step 4
5
Figure 5
SORELLE
Model shown is example only.
Style may vary.
Model shown is example only.
Style may vary.
Use 4 pcs Bolts (b) with 4 pcs Washers(h)
& Lock Washers (i)to attach Left End(A)
& Right End(B) to Head Board(D).
As shown in Figure 4.
(f)
(i)
(h)
(f)
(i)
(h)
(f)
(i)
(h)
(C)
Use 6 pcs Bolt (f) & 6 pcs Washers(h) & 6 pcs Lock Washers(i)
attach Foot Board(C) to Left End (A) & the Right End (B).
As shown in Figure 5.
Step 5
(A)
(B)
(D)
(f)
(i)
(h)
(f)
(i)
(h)
(f)
(i)
(h)
Figure 4
(b)
(h) (i)
(A)
(A)
(D)
(D)
(B)
(B)
(D)
(b)
(h) (i)
(b)
(h) (i)

475# Torino Crib assembly instructions ( JW ) SORELLE
6
Model shown is example only.
Style may vary.
FINALLY CHECK
• PRIOR TO USING THE CRIB, ENSURE ALL BOLTS ARE TIGHTENED. DO NOT OVER TIGHTEN.
• ENSURE THAT THE MATTRESS IS THE RECOMMENDED SIZE.
• ENSURE THE MATTRESS BASE IS LOCATED AT THE CORRECT LEVEL TO SUIT THE CHILD.
• CRIB IS NOW READY FOR USE.
TODDLER BED and FULL SIZE BED ASSEMBLY ( Option Purchase )
Contact the store where you purchased the crib or
visit www.sorellefurniture.com to locate a dealer near you.
Disassembling Crib for Storage
To disassemble crib for storage, follow assembly steps in reverse.
Store all parts and hardware together in a safe place. Store the instruction manual in the supplied
envelope attached to mattress support base for future reference for reassembly.
To clean, use only mild household soap and warm water. DO NOT use bleach or detergent. DO
NOT use abrasive cleaners which can scratch the finish. Use clean soft cloths to wash, rinse and
dry. With proper care, the quality finish will last a long time. Wood surfaces may be treated with
a light application of a good grade of non-toxic furniture polish. Read contents on back of polish
to make sure polish will not harm unit.
Store all parts from Crib, which are not used for Full Size Headboard, in original carton(s) (if
available) to prevent damage and allow reuse.
Cleaning and Storage
Note: The Toddler rail (#136) and Adult rail (#215) are sold separately to convert
the crib to a Toddler bed and a full size bed for your choose.