Soundoff Signal PINNACLE EPL7PD C Series User manual

NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
EPL7PD(x)C_EPL7000 0121
1.800.338.7337 / www.soundo󰀨signal.com
1
Please see reverse for Technical Specications
INSTALLATION:
1) Determineaclean,atlocation(typicallyroof)on
thevehicletomountthePINNACLEMiniLightbar.
ThePINNACLEMiniLightbarcomeswithtwo
(2)steelbracketswhichshouldbeusedto
permanentlymountthelightbartoavehicleroof
orsimilarhorizontalsurface.
2)Positionthebarwithbracketsattachedandmark
holecenters.Centerpunchordrillpilotholesfora
1/4”sheetmetalscrew(customersupplied).
3)Placealockingwasheroverthescrewand
securelyfastenthebracketstothemounting
surface.Thescrewsandholesshouldbecaulked
withasiliconebasedmaterialtopreventleakage.
DO NOT OVERTIGHTEN!
4)Makeelectricalconnections.
Caution: Do not install this product or route any
wires in the air bag deployment zone. Refer to
your vehicle Owner’s Manual for the location of
any air bag deployment zones.
EPL7000 MINI LIGHTBAR PERMANENT MOUNT
•HIGHCURRENTinterconnectsmustbeproperlyterminated.Poorcrimpqualitycancauseheat
build-upandre.Followcrimpconnectormanufacturerinstructions.
•DONOTinstallthisproductorrouteanywiresintheAirBagDeploymentZone.Refertovehicle
Owner’sManualfordeploymentzones.
•DoNOTusesystemtodisconnectheadlights,brakelightsorothersafetyequipment.
•Unitmaybecomehottotouchduringnormaloperation.
•Failuretoproperlyinstallconnectors,fusesorwiringmaycausevehiclefailureorre.
•Installationmustonlybeperformedbytrainedtechnician.Installermustdeterminevehiclewiring
congurationandproperintegrationofsystem.
•Useproperwiregauge.Allpowerwiresconnectingtopositive(+)ornegative(-)batteryterminal
orlocalchassisground(-)mustbesizedtosupplyatleast125%ofmax.currentandproperlyfusedat
powersource.
•Installprotectivegrommetswhenroutingwirethroughrewallormetal.
WARNING
!
WARNING
This product contains high intensity LED devices.
To prevent eye damage, DO NOT stare into the
light beam at close range.
EPL7PD(x)C LowBracket(shown)
EPL7PD(x)A
EPL7HD(x)C HighBracket
EPL7HD(x)A

NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
EPL7PD(x)C_EPL7000 0121
1.800.338.7337 / www.soundo󰀨signal.com
REPLACEMENT PARTS & ACCESSORIES
PMB3BKT-ReplacementPermanentMountBracket(each)
PMB3BRKT-ReplacementPermanentMountBracket(kit)
PMB3TDC-EPL7000ReplacementClearDome
TECHNICAL SPECIFICATIONS
OverallDimensions: 14.25”Lx8.27”Wx2.93”H
FlashPatterns: 29ashpatterns
InputVoltageRange: 10-16Vdc
CurrentConsumption: 2Amps(Avg)-4Amps(Max)
#ofLEDs: 24Generation3LEDs
OperatingTemperature: -40ºto+65ºC
CordLength: 125.75”
Flash Patterns
Number/Name Modules Affected
1.Warp Alternating
2.Quad “
3.Quad2 “
4.Quint “
5.Double2 “
6.Warp1,2,3 “
7.Progressive “
8.Q-Switch™ “
9.Intercycle “
10.Warp WholeBar
11.Quad “
12.Quad2 “
13.Quint “
14.Double2 “
15.Warp1,2,3 “
16.Progressive “
17.Warp Diagonal
18.Quad “
19.Quad2 “
20.Quint “
21.Double2 “
22.Warp1,2,3 “
23.Progressive “
24.Q-Switch “
25.Intercycle “
26.Rotator “
27.Cycle1 Random
28.Cycle2 “
29.Cruise WholeBar
ELECTRICAL:
PATTERN CHANGE
Whilethelightbarisoperational,touchthe
WHITEWIREto10-16Vdcandholdforlonger
than1.5seconds.Alllightengineswillsteady
burn,turnoff,andthenstartashingthenext
patternonthelist.ReleasetheWHITEWIRE
afterthebarresumesashing.Ifmultiple
patternchangesarerequired,thepowermust
becycledaftereverychange.
ThePINNACLEMiniLightbarfeaturesnon-
volatilememoryandwillrecalllastpattern
used.
Selectedpatternwillremainthedefaultonce
turnedoffandcanbechangedbychangingthe
ashpatternbeforepoweringoff.
ACTIVATE/DEACTIVATE CRUISE
Whilethelightbarisoperational,touchthe
WHITEWIREto10-16Vdcforlessthanone
second.Thelightbarwillentercruisemode.
Thelightbarwillremainincruisemodeunless
poweriscycledortheWHITEWIREistouched
to10-16vDCforlessthanonesecondagain.
FOLLOW DIAGRAM BELOW FOR ELECTRICAL CONNECTIONS
REDWIRE:Connectthroughaswitchandfuseto10-16Vdc
BLACKWIRE:Connecttoagoodreliableground(-)
WHITEWIRE:Momentary,connectto12V(+)
EPL7000 MINI LIGHTBAR PERMANENT MOUNT
RED BLACK
WHITE
5 AMP
FUSE
+12 Vdc
PINNACLE
LIGHTBAR