Spaceman Aurora User manual

User Manual

Controls the speed of the modulation in LFO 1 & TAPE 1 modes.
In LFO 2 & TAPE 2 modes it controls the RISE time. Sets the static
delay time in COMB filter mode.
The Aurora is an analog BBD flanger with a focus on sound quality and
flexibility. Exploring the controls of the Aurora will reward the user with
several shades of flange, vibatro, chorus, phase, and filtery spatial effects.
Setting the Aurora apart from the pack is not just the inclusion of creature
comfort controls, like dedicated VOLUME and MIX, but also five distinct modes
of modulation ranging from classic to experimental. Plug in and slip into the
ephemeral night. Let your imagination coast across the neon sky.
VOLUME - Unity gain is roughly at noon, and a moderate boost of 6dB is
possible at maximum.
MIX - Full control over wet/dry blend. This dramatically increases the
utility of the Aurora by opening up subtler and more extreme tones.
REGEN - The staple jet sound maker. This control feeds a portion of the
output signal back into the input for exaggerated resonant, robotic, or
swooshy effects.
MODE - Five modulation modes are available: LFO 1, TAPE 1, LFO 2, TAPE
2, and COMB; each with their own unique attributes. See the tables for a
more in depth coverage of each mode.
WIDTH - This is the main depth control of the modulation. It sets how wide
the sweep is by controlling how much of the total delay time is modulated.
Controls which portion of the delay time is modulated in LFO
1 & TAPE 1 modes. In LFO 2 & TAPE 2 modes it controls the FALL time of
the modulation. Sets a secondary static delay time in COMB filter mode.
TRIG Footswitch - Multi-function footswitch for use with the modulation
bus. See the tables for a more in depth coverage of its usage in each mode.
BYPASS Footswitch - True-bypass soft-touch relay switching to engage and
disengage the effect.
The Aurora requires external power of 9V DC, negative center via the
2.1mm jack. The Aurora has a high 1M ohm input impedance and a maximum current
draw of 58mA when the effect is engaged. Please contact Spaceman if you are
unsure about your DC adapter.
For user guides and recommended settings visit spacemaneffects.com/aurora
All Spaceman pedals are covered by a Limited Lifetime Warranty.
RATE •↑-
RANGE •-
↓

The Aurora is capable of multiple types of modulation. Here is
an in-depth description of the functionality of each mode.
Modulation Bus

TRIG Footswitch Tap: Reset LFO to bottom of sweep
Hold: Reset and hold LFO off at bottom of sweep
RATE • ↑Speed of the LFO modulation
RANGE • ↓How high the modulation sweeps
WIDTH How wide the sweep is (how low it goes)
LFO 1 - Classic Flange/Chorus/Vibrato
(triangle waveshape)
This works just like traditional flanger pedals. The RANGE control functions like a Manual or
Delay time control, the only difference is that it is always active while on most flangers, it is
only active when width is not set at max. This is the best mode for dialing in phase/chorus
sounds using the WIDTH and RANGE knobs.
TRIG Footswitch Hold: Sweep rises at the speed set by the Speed knob
Release: Sweep falls at the speed set by the Speed knob
RATE • ↑Rise and Fall speed of the modulation
RANGE • ↓How high the modulation sweeps
WIDTH How wide the sweep is (how low it goes)
TAPE 1 - Tape mode using the control layout of LFO 1
(triangle waveshape)
This mimics the action of putting your finger on the tape flange to create the classic tape
deck flange effect. The sweep has symmetrical RISE & FALL with variable RANGE (height).
Aurora Modulation Bus

TRIG Footswitch Tap: Toggles between the RATE & RANGE filter settings
RATE • ↑Sets the Frequency of the filter effect (fixed delay time # 1)
RANGE • ↓Sets the Frequency of the filter effect (fixed delay time # 2)
WIDTH Fine control of the filter frequency
COMB - Comb filter mode
(static filtering/no sweep)
This emulates a fixed comb filtering effect by utilizing a short non-swept variable delay
time. This Haas Effect can thicken and add dimension to your sound. REGEN will make it very
metallic and intense.
Aurora Modulation Bus

Width: 3.68 inches / 93.5 mm
Depth: 4.73 inches / 120 mm
Height: 2.25 inches / 57 mm
Weight: 14.6 ounces
Input Resistance: 1M Ohm
Bypass Current Draw: 24mA
Engaged Current Draw: 58mA
Input Voltage: 9-12V DC, negative center via the 2.1mm jack
Please contact Spaceman if you are unsure about your DC adapter.
Technical Specifications

TRIG Footswitch Hold: Sweep rises at the speed set by the Speed knob
Release: Sweep falls at the speed set by the Range knob
RATE • ↑Rise speed of the modulation
RANGE • ↓Fall speed of the modulation
WIDTH How wide the sweep is (how low it goes)
TAPE 2 - Tape mode using the control layout of LFO 2
(triangle/ramp up/ramp down waveshape)
This mimics the action of putting your finger on the tape flange to create the classic tape
deck flange effect. The sweep has user controllable RISE & FALL speeds with RANGE (height)
fixed at maximum.
Aurora Modulation Bus
TRIG Footswitch Tap: Reset LFO to bottom of sweep
Hold: Reset and hold LFO off at bottom of sweep
RATE • ↑Rise speed of the modulation
RANGE • ↓Fall speed of the modulation
WIDTH How wide the sweep is (how low it goes)
LFO 2 - Flange/Chorus/Vibrato - variable rise & fall times
(triangle/ramp up/ramp down waveshape)
This works like LFO 1, except you get control over RISE & FALL times separately. The RATE &
RANGE controls have an effect on the speed AND waveshape of the modulation.

On the following pages you’ll find a collection of carefully
crafted settings to get your started on your journey.
Suggested Settings

Chorus
Vibrato
Aurora Suggested Settings

Aurora Suggested Settings
Slow Tape Flange
Thicc

Aurora Suggested Settings
Down Sweep Flange
Woozy

Asymmetric Tape Flange
Aurora Suggested Settings
Jangle Canyon

Jet Fuel
Aurora Suggested Settings