Spark Fabrica SF-180 User manual

www.sparkfabrica.com
MOVING HEAD FLAMER
SF-180
USER MANUAL
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL SF-180

CONTENTS
1 PRODUCT INTRODUCTION
1.1 PRODUCT OVERVIEW
1.2 BOTTOM RACKET INSTALLATION
1.3 PRODUCT ACCESSORIES
1.4 FUEL ALLOWED
1.5 PRODUCT FEATURE
2 TECHNICAL PARAMETERS
3 BACK PANEL GUIDE
3.1 BACK PANEL INTRODUCTION
4 INTERFACE
4.1 LED DISPLAY AREA
4.2 WELCOME INTERFACE
4.3 MAIN INTERFACE
4.4 ALERT MESSAGE
4.5 INTERFACE SETUP
4.6 ADVANCED INTERFACE
5 OPERATION GUIDE
5.1 INSTALLATION DIRECTION
5.2 FAST OPERATION GUIDE
5.3 FIRING ANGLES
5.4 DRIVEN TIME
6 CONTROL OF TORNADO FLAMER
6.1 SIMPLE IGNITION SEQUENCE LIST
6.2 STEP IGNITION SEQUENCE LIST
6.3 WAVE SEQUENCE LIST
6.4 ADDITIONAL SEQUENCE LIST
7 DMX CONTROL
7.1 ANGLE SETUP
7.2 SPEED SETUP
7.3 IGNITION ON/OFF
7.4 DURATION SETUP
7.5 FIRING SEQUENCE SELECTION
7.6 PUMP WORKING MODE SETUP
7.7 DMX CONTROL
7.7.1 EXAMPLE OF DMX CONTROL
7.7.2 EXAMPLE OF WAVE SEQUENCE
7.7.3 EXAMPLE OF FIXED DURATION
8 MACHINE MAINTENANCE
8.1 CT-05 INTRODUCTION
8.2 SELECT FLAME MACHINE
8.3 SELECT SHOOTING SERIAL NUMBER
8.4 EDIT THE FILE
9 WARRANTY INSTRUCTIONS
10 WARRANTY CARD
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A3
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A3
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A4
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A4
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A8
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A4
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A5
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A8
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A9
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A9
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A10
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A10
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A13
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A14
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A11
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A10
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A14
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A14
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A15
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A16
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A17
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A18
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A22
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A25
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A21
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A24
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A24
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A21
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A21
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A22
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A5
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A7
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪ ▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A18
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪ ▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A19
▪▪▪▪▪▪▪▪▪▪ ▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A20
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A20
▪▪▪▪▪▪▪▪▪▪ ▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A19
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A20
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A8
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A7
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A8
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A22
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A23
▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪▪A23

www.sparkfabrica.com
★ Please read this manual carefully before operating this product.
★ Warranty card attached in the manual, please keep it well.
Unauthorized repair are prohibited, it may cause serious incident.
Make sure power supply in consistent with the rated voltage of the equipment,
and the socket must well grounded. Unplug and turn off the machine when not
use.
Before connect the power cable, communication DMX cable should well
connected and ensure the command keep at firing OFF status. And safety lock
stay at test mode.
The device can only be placed horizontally. Safety distances are marked on the
device (at least 15m in all projection directions, at least 5m to the other sides of
the device).
After turning on the device, no person allows to stay in the danger area. Ensure
all persons that are part of the show be informed about the safety distance, risks
and functions of the device.
Always have a CO2 fire extinguisher and an extinguishing blanket in case of
needed.
If there be any doubt as to the safety operation of the device in any circumstanc-
es, the device should be taken out of service immediately. Be sure the device is in
good operating condition before use. If fail to fire correctly, immediately shut
down and check it accordingly.
Be sure to use high quality flame fluid, otherwise, it is easily lead to failure or
danger. Be careful when refill the flame fluid tank. Please keep flame fluid away
from heat source, sparks, fire or other possibility of ignition. Do not smoke!
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A1

www.sparkfabrica.com
DISCLAIMER
1.Ignoring warnings or regulations as shown on MOVING HEAD FLAMER or this manual.
2.Use for other applications or circumstances other than those indicated herein.
3.Changes to the MOVING HEAD FLAMER, including use of non-original spare parts.
4.Removed safety cover without authorization from SPARK FABRICA.
5.Use this machine by unqualified or untrained personnel.
6.Improper use of machine.
SPARK FABRICA excludes liability for unsafe situations, accidents and damages resulting from：
FOREWORD
Thanks for choosing SPARK FABRICA MOVING HEAD FLAMER SF-180. Please read following
manual carefully and completely before operating this product. Operate according to instructions is
very important for safety, and can elongate the service life of the machine.
Strictly follow the instruction in the manual when operate MOVING HEAD FLAMER SF-180. If you have
any doubts, please contact SPARK FABRICA by [email protected].
We assume the person who use or come in contact with the device are familiar with how the device
should be handled. This includes proper use, maintenance and repair of the machine as defined in this
user manual.
The operator responsible for the control of MOVING HEAD FLAMER must always
have a clear view of the device, so that he/she can stop the show immediately
when there is danger. The main AC power switch should near operator. So that
operator can turn off the power of all devices in case of abnormal.
The device shall not be altered and applied to other use purpose.
Notes for use of Battery power supply: MOVING HEAD FLAMER SF-180 with
stable internal circuit design, please supportSF-180 with battery voltage higher
than 12V. The driving speed of motor won’t change because of the decrease of
battery power supply. Battery options: 12V lead-acid battery (above 30AH, with
more than 24h standby). For Lithium battery, please use battery with output above
30A. Socket type: NEUTRIK-NL4FX, 4 pin sound coupliers (1+ connect 12V anode,
1- connect 12V cathode). Connecting power cables should above 14AWG.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A2

1. PRODUCT INTRODUCTION
www.sparkfabrica.com
This product belongs to special effects equipment, only for professional use.
This product its special fx equipment project flames, it can be controllled by DMX to display 89 flame
combinations.This product is widely used in weddings, concerts, sports events, event meetings and so
on.Stimulate your interest and light up your activity.
1.1 PRODUCT OVERVIEW
Top Panel
Control Panel5.Control Panel
Firing Head
Handle
Fuel Bottle Area
Safety Loop
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A3

www.sparkfabrica.com
1.2 BOTTOM RACKET INSTALLATION
ISOPROPANOL / ISOPAR G,H,L,M / BIOETHANOL.
Connection dimension diagram of bottom bracket of the flamer。
1.4 FULE ALLOWED
Open the package carefully and check to make sure the goods are in good
condition.
1.3 PRODUCT ACCESSORIES
User Manual
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A4
1.6 Meter Power Plug
3 Meters Power Pair Cable
3 Meters DMX Pair Cable
NOTICE

www.sparkfabrica.com
2 TECHNICAL PARAMETERS
★ Compact pumping system ensure compact size of machine.
★ Double electromagnetic valves design for additional safety.
★ Tilt protection, the tilt sensor will be activated when machine slant Over 45° .
★Unique safety lock design, device can't firing when locked, avoid spurious triggering.
★ Intelligent control system: pressure monitoring, safety warning, no fuel alarming, system failure
warning etc..
★ High performance nozzle, reliable and durable.
★ High-accuracy swiveling head driving and controlling system, allows for fast and precise flame bursts.
★ Strengthened and rustproof metal panel, water-proof design.
★ Neutrik PowerCON TRUE1 and DMX socket.
★ Fitted with fireworks ignition signal port, can be triggered by fireworks ignition.
★ Flame effects up to 8-10m (no wind), with 210° (±105°) swiveling angles.
★ As much as 88 preset flame sequences are available. It is easier and stable to running the
MOVING HEAD FLAMER when controlled by SPARK FABRICA Pyro Sim Console CT-05
1.5 Functional Characteristics
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A5
Only the consumables provided by Spark Fabrica are allowed to be used. Spark Fabrica shall
not be liable for any damage to machines, personnel and property caused by the use of
consumables not provided by the company.

www.sparkfabrica.com CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A6
Manufacturer SPARK FABRICA
MOVING HEAD FLAMER
SF-180
100-120V，50 / 60HZ
200-240V，50 / 60HZ
320W
Name
Model
Work Power
Power Input Connector SEETRONIC
SEETRONIC
Power Output Connector
DMX Signal Interface
Signal Interface
Signal Interface
IP Rate IP55(Waterproof Design)
3 PIN / 5PIN Double DMX Interface
3 PIN / 5PIN Double DMX Interface
9V-60V Fireworks Ignition Signal Interface
10LFuel Bottle Capacity
N/A
Control Protocol DMX-512
Control Mode
Wireless Control
Standard DMX Signal Control
√(Within 2 km)
Effect Angles Vertical
SMPTE Touch Screen Console Support
Power Plug SEETRONIC （1.6Meter)
Remote Controller Optional
DMX Cable √ 3Meter
√ 3Meter Power Cable
Safety Loop √
√Safety Rope
Update Box Optional
Net Weight (No Fuel) 32kg
30ml/s
60ml/s
Gross Weight
Firing Head L
(Standard Configuration)
Firing Head L
(Standard Configuration)
Ignition Mode High Voltage Electronic Ignition
42kg
Machine Dimensions - L*W*H 590mm*360mm*370mm
722mm*482mm*574mm
Packing Dimensions - L*W*H
Kind ISOPROPANOL, ISOPAR G,H,L,M
Input Voltage & Frequency
Identification
AC Power
Interface Type
Waterproof
Hopper
Control
Accessory
Weight
Ignition
Oil Consumption
Dimensions
Fuel Oil
Removable Hopper

www.sparkfabrica.com
3 BACK PANEL GUIDE
3.1 BACK PANEL INTRODUCTION
DC 9V-60V Fireworks
Ignition Signal Port
BAT
Safety Loop
Fuse
LCD Screen
Operate Panel
3-pin DMX Socket
5-pin DMX Socket
5-pin DMX Socket
3-pin DMX Socket
INPUT AC 100V-240V
Safety Lock
Indicator Light
ON/OFF Switch
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A7

www.sparkfabrica.com
4. INTERFACE
4. 1 LED DISPLAY AREA
4. 2 WELCOME INTERFACE
4. 3 MAIN INTERFACE
Radio receiving (reserved).
Switch interface to setup
parameter.
DMX signal. Flash means DMX
signal available, otherwise no
DMX signal
ERR
ENTER
PUMP
LED Display Area
+
RX
MENU
First Line: Product Model
and software version.
Second Line: Equipment series
number.
Parameter Down
Parameter Up
Light on when pump is running
Light on when there is an
error.
Confirm and save parameters
(screen will flash when
parameters saved)
-
DMX
SF-180
SF-XXXXXX
First Line: DMX Address
Second Line: Pressure100
DMX Address: 1
P:100 V:13.6
(e.g. 100=10bar); V: 13.6 means internal
voltage is 13.6V.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A8
screen display will switch to main interface if don't press button for a long
time.
NOTICE

www.sparkfabrica.com
E0
Factory Mode
Test Mode
Invert ON
Motor Disable
E1 Pressure Err
E2 P Relief Err
Safety lock located at TEST MODE.
DMX signal blocked in factory mode.
When turned on, all angles will be mirrored.
Pressurize for about 13s, pressure value failed to reach 100%, system
will report E1. Possible fault: No fuel, pump failure, pipeline problem etc.
When turned on, the position of the firing head should be moved
or set manually, and the motor of firing head will be disable
(The flamer should be restarted before it takes effect.)
Pipeline can't release pressure leads to pressure relief error.
Possible fault: pressure release valve failure, pipeline problem or
control system problem etc.
When Ext Ignite is ON, device will pressurize automatically when
switch safety lock to USER MODE; decompression when switch to
TEST MODE. 9V-60V fireworks ignition signal will trigger related
firing sequences.
E3 Motor Err
E4 ExtIgnition ON
Possible fault: swiveling nozzle stuck, motor failure etc.
E5 Voltage Err Battery voltage>15V or <10V for continuous 5s, machine stops
running Possible fault: the battery is low.
E6 Tip Err if the machine slant over 45° , it stops running, system will report E6.
Alert Message Explanation
1~512 DMX address setup
Restrict nozzle rotate angles: Set by "+" and "-" , and
confirm by "ENTER"
Maxi. ANGL：NO.1-NO.15
Mini. ANGLE：NO.1-NO.15
Set DMX Address
Angle Limit
Menu Range Explanation
4. 4 ALERT MESSAGE
4. 5 INTERFACE SETUP
Press “MENU” to switch through setup menu.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A9

www.sparkfabrica.com
OFF / Motor/ Pump / Igniter
/ Relief Valve / Jet Valve
Ext Ignite
Set Ext Sequence
Language
Mode Select
Motor Disabled
Swiveling and stop at target angle.
Pump running 1s, if pressure reached the target value, the pump
will not running.
Ignite 1s.
Trigger through 5-60V fireworks ignitor signal.
Preset sequence triggered by fireworks ignitor.
Language switch.
Factory mode is for test in factory only.
When turned on, the position of the firing head should be moved or
set manually, and the motor of firing head will be diabled.
(The flamer should be restarted before it takes effect.)
1.Motor
2.Pump
3.Ignite
Reset default parameter settings.
Items Contents
Drive Test
Release valve will be on and off for 3 times.
Safety lock located at user mode, release pressure for 5s, jet valve
will be on and off for 3 times.
4.Relief Valve
5.Jet Valve
OFF / ON
1~88
English/Chinese
Normal Mode / Factory Mode
OFF / ON
DefaultParameter OFF / ON
Description
4. 6 ADVANCED INTERFACE
5 OPERATION GUIDE
5.1 INSTALLATION DIRECTION
Press “MENU” 3s enter advanced interface, press “MENU” to switch interface, press “MENU”
3s can back to main interface.
Please read the safety distance print on the top panel of MOVING HEAD FLAMER carefully.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A10

www.sparkfabrica.com
(1) 1 to 15 is the firing angle of MOVING HEAD FLAMER, Far Right is position 15, Middle is position 8,
Far Left is position 1.
(2) Audience side and control side are indicated in above picture.
(3) Safety distances for MOVING HEAD FLAMER are indicated in above picture. At least 15m in all
projection directions, at least 5m to the other sides of the device.
5.2 FAST OPERATION GUIDE
Immediately upon receiving the machine, carefully unpack the carton, check the machine received in
good condition. Ensure safety operation of machine, please do following below operation procedures
when operate MOVING HEAD FLAMER.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A11
in order to indicate correct direction, please place the top panel correctly.
NOTICE

www.sparkfabrica.com
1.Installation
3.Fueling Please fueling with high quality fuel according to requirement of this manual.
Operation step Schematic Diagram and Explanation
Explanation
Before operate machine please locate safety lock at TEST MODE.
TEST MODE: operator can test the rotate of nozzle, but the fuel
ejection function disabled, so there is no fuel eject and flames.
USER MODE: the device can generate flames normally. Please
strictly follow the safety distance requirement, remove all human,
animal or flammable objects in the danger area.
Two kind of power supply optional:
1.110V/220V main power supply
12V battery power supply
Please confirm safety lock located at TEST MODE before switch on
the POWER ON/OFF.
MOVING HEAD FLAMER occupy 6 channels.
Detail information please refer to the table of page20-22.
Host controller: Press”HEAT”
DMX console: switch DMX value of channel 6 to 50-200
Host controller: Press “HEAT” key
DMX console: switch DMX value of channel 6 to 0-49/201-255
Reconfirm safety lock located at TEST MODE before test. In this
status, the nozzle will rotate, and igniter will activated, but there is no
flame.
When use DMX console to test the sequence, suggest to set CH1 at
128, so that nozzle stay at straight up position after each sequence.
The device can only be placed
horizontally, if placed on truss, please
locked with extra safety ropes.
2.Locate safety lock
at TEST MODE
4.Power and DMX
cable connection
5.Switch ON the
machine
6.Set DMX address
7.Pressuriser
8.Check device status
in TEST MODE
9.Pressure Relief
10.Switch safety lock
to USER MODE
11.Pressuriser
12.Firing
13.Pressure Relief
Before switch to USER MODE, Please strictly follow the safety
distance requirement, remove all human, animal or flammable
objects in the danger area.
Host controller: Press”HEAT”
DMX console: switch DMX value of channel 6 to 50-200
Set firing sequence Host controller: Press “FIRING” key
DMX console: switch DMX value of channel 3 to 254-255
Relief pressure when show finished or MOVING HEAD FLAMER not
use for a long period.
Host controller: Press “HEAT” key
DMX console: switch DMX value of channel 6 to 0-49/201-255
Set DMX Address 1
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A12

5.3 FIRING ANGLES
The firing angle for MOVING HEAD FLAMER is ±105°, from the Audience Side view, there are
altogether 15 firing angles as below.
www.sparkfabrica.com
Operation step
Schematic diagram and explanation
Explanation
14.Switch safety lock
to TEST MODE
15.Power off
Guarantee safety use for next time.
Power off MOVING HEAD FLAMER, tear down power cable and
DMX cable, pack up the device when it is cooled down.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A13

www.sparkfabrica.com
-105° 170ms
No.
NO.1
-90° 150ms
NO.2
-75° 130ms
NO.3
-60° 110ms
NO.4
-45° 90ms
NO.5
-30°
-105°
Single Ignition SHORT flame
Single Ignition SHORT flame
Single Ignition SHORT flame
Single Ignition SHORT flame
Single Ignition SHORT flame
Single Ignition SHORT flame
Static 0.418s 3-5
Static 0.395s 6-7
Static 0.370s 8-10
Static 0.344s 11-12
Static 0.324s 13-15
Static 0.303s 16-17
-90°
-75°
-60°
-45°
-30°
70ms
NO.6
-15° 50ms
NO.7
0° 0ms
NO.8
15° 50ms
NO.9
30° 70ms
NO.10
45° 90ms
NO.11
60° 110ms
NO.12
75° 130ms
NO.13
90° 150ms
NO.14
105° 170ms
NO.15
Angles Drive time needed
1
2
3
4
5
6
No. Ignition angle
Description
Nozzle Movement Firing Duration (For reference)
CH5 DMX Reference Value
5.4 DRIVEN TIME
Time needed for the motor drive from NO.8 to relevant angle.
For example for the motor drive from 0°to 45°, it need 90ms, when operator design a show to
synchronize to music, this drive time must be calculated.
MOVING HEAD FLAMER SF-180 has 88 preset sequences, operator use related channel DMX value
or sequence No. to access certain sequence. Below, you can find sequence list and single ignitions.
6.1 Single Ignition Sequence List
6 CONTROL OF TORNADO FLAMER
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A14

Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
Single Ignition SHORT flame
Static
-105°
-90°
-75°
-60°
-45°
-30°
-15°
0°
15°
30°
45°
60°
75°
90°
105°
-15°
0°
15°
30°
45°
60°
75°
90°
105°
0.278s 18-20
0.258s 21-22
0.278s 23-25
0.303s 26-28
0.324s 29-30
0.344s
0.370s
0.395s
0.418s
0.760s
0.737s
0.711s
31-33
34-35
36-38
39-40
41-43
44-45
46-48
7
8
9
10
11
12
13
14
16
17
18
15
Step from 1-15
Step from 15-1
Step 5>8>11
Step 11>8>5
Step 6>10
Step 10>6
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
L -> R 2.66s 80-81
R -> L 2.66s 82-84
L -> R 0.92s 85-86
R -> L 0.92s 87-89
L -> R 0.75s 90-91
R -> L 0.75s 92-94
6.2 STEP IGNITION SEQUENCE LIST：
www.sparkfabrica.com
0.686s 49-50
0.666s 51-53
0.645s 54-56
0.620s 57-58
0.599s 59-61
0.620s
0.645s
0.666s
0.686s
0.711s
0.737s
0.760s
62-63
64-66
67-68
69-71
72-73
74-76
77-79
19
20
21
22
23
24
25
26
28
29
30
27
31
32
34
35
36
33
No.
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A15
Ignition angle
No.
Ignition angle NO.
Description
Description
Nozzle Movement
Nozzle Movement
Firing Duration (For reference)
Firing Duration (For reference)
CH5 DMX Reference Value
CH5 DMX Reference Value

www.sparkfabrica.com
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
SHORT flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
LONG flame Step sequence
6.3 WAVE SEQUENCE LIST：
Step 4>6>8>10>12
Step 12>10>8>6>4
Step 8>6>10>4>12
Step 8>10>6>12>4
Step from 1-15
Step from 15-1
L -> R 1.27s 95-96
R -> L 1.27s 97-99
M>L>R>L>R 1.60s 100-101
M>R>L>R>L 1.60s 102-104
L -> R 7.78s 105-107
R -> L 7.78s 108-109
37
38
40
41
42
39
Step 5>8>11
Step 11>8>5
Step 6>10
Step 10>6
Step 4>6>8>10>12
Step 12>10>8>6>4
L -> R 1.82s 110-112
R -> L 1.82s 113-114
L -> R 1.25s 115-117
R -> L 1.25s 118-119
L -> R 2.68s 120-122
R -> L 2.68s 123-124
43
44
46
47
48
Step 8>6>10>4>12
Step 8>10>6>12>4
M>L>R>L>R 2.88s 125-127
M>R>L>R>L 2.88s 128-130
49
50
45
Wave 5 -->11
Wave 11-->5
Big wave 1--15
Big wave 15--1
Wave 8-->1
Wave 8-->15
Middle wave sequence
Middle wave sequence
Middle wave sequence
Middle wave sequence
Middle wave sequence
Middle wave sequence
L -> R 1.87s 131-132
R -> L
L -> R
R -> L
1.87s 133-135
LONG wave sequence 4.08s 136-137
LONG wave sequence 4.08s 138-140
M -> L 2.09s 141-142
M -> R 2.09s 143-145
51
52
54
55
56
53
Wave 1-->8
Wave 15-->8
Wave 8-->11
Wave 8-->5
Wave 5-->8
L -> M 2.31s 146-147
R -> M 2.31s 148-150
M -> R 0.99s 151-152
M -> L 0.99s 153-155
L -> M 1.08s 156-158
57
58
60
61
Wave 11-->8 R -> M 1.08s 159-160
62
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
59
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A16
No. Ignition angle NO. Description Nozzle Movement
Firing Duration
(For reference)
CH5 DMX
Reference Value
No.
Ignition angle NO.
Description Nozzle Movement
Firing Duration
(For reference)
CH5 DMX
Reference Value

LONG wave sequence
LONG wave sequence
LONG wave sequence
LONG wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
LONG wave sequence
LONG wave sequence
LONG wave sequence
LONG wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
SHORT wave sequence
6.4 ADDITIONAL SEQUENCE LIST：
Step 3>13
Step 13>3
Step 3>13
Step 13>3
Step 8-13
Step 13-8
Step 8-13
Step 13-8
L -> R 0.93s 161-163
R -> L
L -> R
R -> L
0.93s 164-165
1.63s 166-168
1.63s 169-170
M -> R 1.55s 171-173
R -> M 1.55s 174-175
www.sparkfabrica.com
63
64
66
67
68
65
Step 8-3
Step 3-8
Step 8-3
Step 3-8
M -> R 3.24s 176-178
R -> M 3.24s 179-181
M -> L 1.54s 182-183
L -> M 1.54s 184-186
M -> L 3.24s 187-188
L -> M 3.24s 189-191
69
70
72
73
74
Step 3-13
Step 13-3
L -> R 1.98s 192-193
R -> L 1.98s 194-196
75
76
71
Step 2-14
Step 14-2
Step 8>5>11
Step 8>11>5
Step 5-11
Step 11-5
L -> R 2.32s 197-198
R -> L 2.32s 199-201
M>L>R 0.93s 202-203
M>R>L 0.93s 204-206
L -> R 1.28s 204-206
R -> L 1.28s 207-209
77
78
80
81
82
79
Wave 8-->13
Wave 13-->8
Wave 8-->3
Wave 3-->8
Wave 3-->13
Wave 13-->3
M -> R 1.70s 212-214
R -> M 1.70s 215-216
M -> L 1.60s 217-219
L -> M 1.60s 220-221
L -> R 3.06s 222-224
R -> L 3.06s 225-226
83
84
86
87
88
8(0°)
Single Ignition LONG flame
Static max. 8s 227-255
Middle wave sequence
Middle wave sequence
Middle wave sequence
Middle wave sequence
>89
85
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A17
No.
Ignition angle NO.
Description Nozzle Movement
Firing Duration
(For reference)
CH5 DMX
Reference Value

CH1
CH2
CH3
CH4
CH5
CH6
Manual Angle setup: (0~255) angle change from -105° to 105°, (128) is straight
upward (0°)
Manual Speed setup: (0) Max Speed, (1~254) Speed increase, (255) Max Speed.
Ignition ON/OFF: (0~253) Ignition OFF, (254~255) Ignition ON.
Program sequence setup: (0-2) no preset sequence; (3-255) preset sequence.
DMX value = 2 + Sequence No.*2.55 (ROUND OFF)
Firing Duration setup: 0 and 255 is permanent fire (8s is limit duration time);
1~254 is 10~2540ms duration time (Manual firing duration = DMX Value * 10ms)
Mode setup: (0~49) Pressure Relief Mode (Emergency Stop), (50~200)
Compression Mode, (201~255) Pressure Relief Mode (Emergency Stop).
Channel Function
www.sparkfabrica.com
-105° 0
Angle No.
1
-90° 18
2
-75° 36
3
-60° 54
4
-45° 73
5
-30° 91
6
-15° 109
7
0° 128
8
15° 146
9
30° 165
10
45° 183
11
60° 201
12
75° 219
13
90° 237
14
105° 255
15
Angle DMX Value
7 DMX CONTROL
7.1 ANGLE SETUP
CHANGSHA SPARK TECHNOLOGY ELECTRONICS CO.,LTD
MOVING HEAD FLAMER USER MANUAL | A18