Speedpulse ENERGIC Instruction Manual

© Speedpulse model 2012 1 [email protected]
ENERGIC
Building instructions
Specifications:
Wingspan 2455mm
Length 1260mm
Wing area 40,4dm
2
Elevator area 4,4dm
2
Wing airfoil F3B special
Elevator airfoil SD8020 mod.
Weight (empty) ca. 1200g
Recommended equipment:
Wing servo’s Hyperion Atlas DS095-FMD
Graupner DES448 BB MG
(max 10mm servo’s)
Elevator Futaba S3156
Hyperion Atlas DS11-SCB

© Speedpulse model 2012 2 [email protected]
Wing:
Flaps lever mounting:
Make a hole in the carbon tube.
If necessary cut the thread at the lever. Glue the lever with 5-min epoxy.

© Speedpulse model 2012 3 [email protected]
Ailerons lever mounting:
Make a hole in the carbon tube.
If necessary cut the thread at the lever. Glue the lever with 5-min epoxy.

© Speedpulse model 2012 4 [email protected]
Servo mounting:
Draw the rod line. Check the position.
Sand the edge of the servo frame
(front).
Use 5-min epoxy for glueing.
It’s recommended to glue the frame with installed servo. You will have no work
(sanding) with overflowed glue.

© Speedpulse model 2012 5 [email protected]
Use 6mm servo lever for ailerons. Make a modification at the metal clevis.
Use 8mm servo lever for flaps. Finished rods for ailerons (top) and
flaps.
Servo lever’s by ailerons and flaps (right) in neutral position.
After setting the deflections and neutral positions glue the threat at the rods with thin
CA glue.
Install the servo covers.

© Speedpulse model 2012 6 [email protected]
Fuselage:
Motor plate mounting:
Sand the surface for motor plate. Sand a little cone at the motor plate.
Check correct spinner position. Glue the plate with very thin CA glue.
Glue the plate finally with 5-min epoxy.

© Speedpulse model 2012 7 [email protected]
Elevator:
Make a hole for elevator lever.
Sand the lever for better adhesion. Glue the lever with 5-min epoxy.
Make a hole for elevator rod.

© Speedpulse model 2012 8 [email protected]
Elevator servo mounting:
Sand the servo area in rudder. Sand little the servo case.
Glue the servo with 5-min epoxy. Fix the rod with some washer or nut and CA glue.
Use 6mm servo lever for elevator.
Install the cables for elevator servo and glue the servo cover.
!!!!! Crimp the connector at the elevator cable after putting thru the fuselage, there is
only a small (5mm) hole in the back rib. !!!!

© Speedpulse model 2012 9 [email protected]
Canopy:
Sand the glueing area and the carbon
rod.
Place and fix the rod with CA glue. Glue it finally with 5-min epoxy.
Antenna’s (ca. 100mm behind wing)

© Speedpulse model 2012 10 [email protected]
Wing connector:
Recommended cable lengths:
Ailerons 70cm
Flaps 25cm
Elevator 90cm
Wing connector in fuselage 20cm
Basic setting for Energic (+ = down, – = up):
Elevator ± 3,5mm (measured in the middle)
Ailerons + 5mm, –13mm
Thermal: + 1,5–2mm, mix Flaps to Ailerons 100% (measured at the root)
Speed: – 1,5mm, mix Flaps to Ailerons 100%
Climbing (motor): –1,5mm, mix Flaps to Ailerons 100%
Butterfly: Flaps + 55mm, Ailerons – 6mm (measured at the tip), Elevator + 6,5mm
Snap-flap: + 4mm, mix Flaps to Ailerons 100%
Mix Ailerons to Flaps: + 1,5mm, – 4mm
Mix Flaps to Ailerons 100% means that both flaps have the same deflection.
CG: 92 – 94mm

© Speedpulse model 2012 11 [email protected]
Recommended motors set’s:
Motor’s from 250 to 350g
NEU 1409/1.5D/6.7+ RFM 15x13 + 3 (?) or 4 (150A, 2,2kW) Li-Po 2800 55C
KIRA 500 FAI F5F 4S + RFM 15x13S + 3 Li-Po 2800 55C (120A)
KIRA 500 FAI F5F 4S + RFM 15x13S + 4 Li-Po 2800 55C (180A)
KIRA 600-30 + 6.7:1 + RFM 17x13 + 6 Li-Po 2200 55C (200A, 4kW)
MEGA 22/40/2 + RFM 14x10 + 3 Li-Po 2800 55C (120A)
KIRA 500-58 + 6.7:1 + RFM 14x10 + 3 Li-Po 2800 55C (180A)