Spooky2 Scalar User manual

Spooky2
Scalar Digitizer
INSTRUCTION
November 2018
Spooky2 Team

Biofeedback is a way of finding out what frequencies are best
suited to your body. Spooky2 Scalar is the only Scalar device
capable of doing biofeedback scan. Spooky2 Scalar Digitizer
measures tiny changes in the scalar field during a scalar
frequency scan. Scalar biofeedback requires the use of two gen-
erators. GX is two generators in one. G2 modulates the Scalar
field, and G1 measures the response. Follow the instructions
below to perform a Scalar biofeedback scan.
1. Connect Scalar Digitizer to the link cable port on the Scalar
Transmitter.
1
Step 1: Hardware
Brief Overview

2
2. Connect the link cable and power cable of Spooky2 Scalar.
3. Connect G1 Out 1 to the BNC port of Spooky2 Scalar Digitiz-
er.

3
4. Connect G2 Out 1 to the BNC port of the Spooky2 Scalar
Transmitter.
5. Connect GX to the computer and short press the Power
button to turn on GX.
6. Turn on and tune your Spooky2 Scalar.

Tip:
GX must not be in the Scalar field, because the case and elec-
tronics in GX are metal, which will distort the field. Please keep
GX 1m away from Spooky2 Scalar Transmitter, and 1m from the
scalar field.
1. Launch the Spook2 software. Please take a note for the corre-
sponding port numbers for G1 and G2, which can be seen on the
GX display. In this example, G1 is Port 14 and G2 is Port 15.
2. Select the Spooky2 Scalar Digitizer Slave (GX) - JW preset,
then go to the Settings tab. In the Output Shadowing frame, set
'Output = [x]’, x = the port number of G1. Here, x=14.
4
Step 2: Software

3. Go to the Control tab, tick Overwrite Generator and choose
G2 (Port 15) to load the settings.
5

6
5. Lie between the two scalar units, and ask an assistant to click
the Scan button to start the biofeedback scan.
4. Then, go back to the Presets tab. Select the BFB Master
preset, go to the Control tab, tick Overwrite Generator, and
choose G1 (Port 14) to load the preset.

7
Note: If you do not have anyone to help, set the Start Delay to
2000. This will give you time to start the biofeedback scan and
position yourself correctly between the units.
G2 will automatically start, causing Spooky2 Scalar to transmit
the generator frequencies. G1 will start, but no frequencies will
be produced. Instead, the amount of Scalar energy being
absorbed for each frequency by the body will be recorded.
When your scan completes, you will see the results presented in
a new window. Save the frequency results by clicking the Save
button.

This will take you to the Create Program window. Name your
scan results set appropriately, then select Save. We suggest
including the person’s name and date. You can edit the Notes if
you wish for future reference.
Spooky2 will automatically refresh the database after adding a
new program. Your new program can now be searched in the
Programs tab.
8

9
Use Spooky Scalar General (SS) - JW preset to run your scan
results.
Tips:
1. It is best to lie perfectly still, and only have one person in the
Scalar field. This field extends outward, so ensure no living
organism is nearby.
2. It is important to make a note which port numbers correspond
to G1 and G2 before running a biofeedback.
3. Spooky2 Scalar BFB Master preset performs the recording.
Spooky2 Scalar BFB Slave preset supplies the frequencies for
Spooky2 Scalar modulation.
4. We suggest using G1 with Spooky2 Scalar BFB Master
preset.
5. You can do short scans once a day and longer scans once a
week.
6. When you run scan results, please remove Spooky2 Scalar
Digitizer. Then use G2 to run your scan results.

www.spooky2scalar.com
Spooky2