Fluke 1653B User manual

CONSULTORÍA ENERGÉTICA
ItresE
LATAM - USA
ANALIZADOR DE INSTALACIONES
BT - FLUKE 1653 B
Manual de Calibración Suplementario
+5411.2115.9585
[e-mail]
www.itresenergia.com

Manual Supplement
© 2011-2017 Fluke Corporation. All rights reserved. ,

Manual Title: 1652C/1653B/1654B Calibration Supplement Issue: 4
Part Number: Web-Only Issue Date: 4/17
Print Date: March 2011 Page Count: 3
Revision/Date:
This supplement contains information necessary to ensure the accuracy of
the above manual.

1652C/1653B/1654B Calibration Manual Supplement
4/17 1
Change #1
On page 20, replace step 4 with:
4. Place PN 1884378 on the touch pad, then touch with the probe as shown in Figure 4.
On page 21, replace Figure 4 with:
280V
RMS
MAX
280V
RMS
MAX
CAT I
1000V
CAT II
600V
RMS MAX
20V PK
30A
RMS
MAX 20V PK
LO LO - SENSE
, HI , mA
V
1500V PK
MAX
50V PK
MAX
20V PK 20V PK
N
LPE
L1 L2 L3HES
OUTPUT
Z
L
, Z
GND,
RCD
HI
LO
HI
LO
METER
METER
5320A MULTIFUNCTION ELECTRICAL
V
ACOM
INPUT
Fluke 5320A
Fluke 1653
PE
(L2/Green)
L
(L1/Red)
PN 1884378
gad002.eps
Figure 4. Touch Pad Sense Test

Manual Supplement 1652C/1653B/1654B Calibration
2 4/17
Change #2
On page 15, add the following to Table 2:
Touch plate FLUKE-165X-8006,TOUCH PLATE Fluke P/N 1884378
On page 25, replace steps 1 through 8 with:
1. Set the UUT rotary switch to LOOP ZINO TRIP function.
2. Using <, set the UUT for L-PE test.
3. Connect test leads to the UUT L-PE-N input jacks. Short the far end of the test leads together with a
Zero Adapter (Fluke P/N 3301338). See Figure 8.
4. Press and hold for approximately three seconds until the UUT ZERO =annunciator appears.
On page 27, replace steps 1 through 7 with:
1. Set the UUT rotary switch to LOOP ZIHI CURRENT function.
2. Connect test leads to the UUT L-PE-N input jacks. Short the far end of the test leads together with a
Zero Adapter (Fluke P/N 3301338). See Figure 8.
3. Press and hold for approximately three seconds until the UUT ZERO =annunciator appears.
On page 28, replace step 7 with:
7. Using the 5320A cursor keys or keypad, set the 5320A Nominal R Value to the nearest value to
those in Table 6 that the 5320A will source. For Steps 1 and 8, take the first value that is t0.2 .
On page 28, replace Table 6 with:
Table 6. Loop ZIHi Current Accuracy Test
Step UUT
Function
UUT<
Setting
5320A
Nominal
R Value
5320A
Residual
Impedance
Correction
Type
Recorded
5320A
Displayed
Output Z
Value
UUT
Accuracy
Spec.
±(% + dig)
UUT
Res.
Calculated UUT
Display Limits
Lower Upper
1
Loop ZIHi
Current
L-PE
0.2 
Comp
+(2 % + 4) 0.01  21.8 
318 
450 
+2 % 0.1 
5180 
6500 
+6 % 1 
71800 
8
L-N
0.2 
+(2 % + 4) 0.01  91.8 
10 18 
11 50 
+2 % 0.1 
12 180 
13 500 
+6 % 1 
14 1800 

1652C/1653B/1654B Calibration Manual Supplement
4/17 3
Change #3, 121
On page 33, Table 10, add the MP12:
MP12 Battery Holder 1676850 1
Change #4 593
On page 10, replace the Test Signals table with:
Test Signals
RCD Type Test Signal Description
AC
(sinusoidal)
The waveform is a sinewave starting at zero crossing, polarity
determined by phase selection (0 qphase starts with low to high zero
crossing, 180 qphase starts with high to low zero crossing). The
magnitude of the test current is I'n x Multiplier for all tests.
A
(half wave)
The waveform is a half wave rectified sinewave starting at zero,
polarity determined by phase selection (0 ° phase starts with low to
high zero crossing, 180 ° phase starts with high to low zero crossing).
The magnitude of the test current is 0.7 x Iǻn (rms) x Multiplier for all
tests where the multiplier is x0.5 (x1/2). The magnitude of the test
current is 2.0 x Iǻn (rms) x Multiplier for all tests where both the
multiplier is x1 and Iǻn = 0.01A. The magnitude of the test current is
1.4 x Iǻn (rms) x Multiplier for all tests for all other settings.
B (DC) This is a smooth DC current according to EN61557-6 Annex A