SportsPlay Equipment 302-133 User manual

302-133 GEO-DOME (Port)
Page 1
Rev 11/29/2010
IMPORTANT
PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be
installed in accordance with these instructions. Check your shipment against Bill
of Lading and Parts list. Any missing or broken parts must be reported to your
distributor within 10 days of receipt of your order. When properly installed and
maintained, equipment will give many years of Safe, Trouble-Free use. Periodically
check for loose or broken parts. Loose bolts must be tightened and broken parts
must be replaced as they can possibly create dangerous situations leading to
unnecessary accidents. Resilient Surfacing should be used under all playground
equipment. Appropriate publications, available at no charge, from the Consumer
Product Safety Commission, include “A Handbook for Public Playground Safety”. You
can receive your free copy by calling 1-301-504-7908.
See page 4 for installation key.
PACKING LIST
HARDWARE BAG
1
CTN
1
Hardware Bag
26
-
116-545
5/16” x 2½” Button HD Bolts
2
CTN
15
303-224
Braces (Blue 2’ 5 1/2”)
52
-
316-501
5/16” Flat Washers
1
CTN
20
303-221
Braces (Red 2’ 8 1/2”)
26
-
216-501
5/16” Hex Nuts
1
CTN
15
303-222
Braces (White 2’ 9”)
26
-
326-501
5/16” Lock Washers
1
-
416-350
3/16” Socket Key
1
-
805-532
Warning Label
1
-
805-534
SportsPlay Label
30
-
905-847
Bolt Caps
1
-
Maintenance Checklist
5 CTN 5 TOTAL PCS WT 125# CLASS 70
Dome footprint is
8’ wide
Dome use/fall zone is a
20’ diameter circle

302-133 GEO-DOME (Port)
Page 2
Rev 11/29/2010
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS:
Stationary & Portable equipment –Use/Fall Zones should Extend a MINIMUM of 6 Feet in All
Directions from the Perimeter of the Equipment Ground Space. This Area should be covered
with the required amount of Resilient Safety Surfacing Material. For some Equipment –
Use/Fall Zones can overlap. See Consumer Product Safety Commission Guidelines.
USE AREA DIAGRAM:
MAINTENANCE:
MONTHLY, check for loose bolts and worn or broken parts. Tighten loose bolts
immediately. If parts are worn or broken, discontinue use immediately and contact your
SportsPlay distributor for replacements.

302-133 GEO-DOME (Port)
Page 3
Rev 11/29/2010
ASSEMBLY AND INSTALLATION:
NOTE:
Extra long bolts are supplied to make assembly possible. After assembly is
complete, all threaded ends of bolts protruding beyond nuts must be cut off
and/or peened to eliminate sharp edges. No more than two threads should
extend beyond face of nut. Bolt Caps are also provided if you would like to
use. These however, must be installed before the nut is put on the bolt. They
are two piece, and the lid can be placed on after bolt is tightened.
STEP #1:
Start with White Braces. Assemble bottom row. On the bottom joints use one
2 ½” button head bolt inserted from the outside with one flat washer under
the head of the button head bolt, through the joint, then a bolt cap, one
flat washer and one lock washer under a 5/16” hex nut. DO NOT TIGHTEN ANY
NUTS MORE THAN A FEW TURNS AT THIS POINT.
STEP #2:
Next assemble all the joints with five Blue Braces, use one 5/16” x 2½”
button head bolt put thru from outside with one flat washer under the head of
the button head bolt, through the joint, then a bolt cap, one flat washer and
one lock washer under the hex nut. (See Plan View Illustration for Color
Code for Braces). Always position bars where ends point up on insideso that
ends of bars pointing down are on outside.
STEP #3:
Now assemble the six unit joints using the 2-1/2” button head bolts, using
the assembly techniques described above.
STEP #4:
Continue this procedure for the final five brace connections at the top.
STEP #5:
NOW TIGHTEN ALL JOINTS SECURELY. If necessary, cut off all bolts ends so
that no more than 2 threads extend beyond the face of the nut. Peen or file
to remove sharp edges. Install the lids on the bolt caps by tapping the lids
into the bolt caps.
Step #6:
Position unit over adequate depth of resilient surfacing.
STEP #7:
Attach warning label and Manufacturer’s Identification label to a clean
surface. The labels should be attached in a location where they are clearly
visible and legible and away from normal hand and foot placement areas. The
labels must be replaced if they become illegible, destroyed or removed.
Contact your SportsPlay distributor for replacements.

302-133 GEO-DOME (Port)
Page 4
Rev 11/29/2010
Installation Key