SportsPlay Independent Spiral Slide User manual

18'
24'
Slide
Independent
Spiral
72"
800-727-8180
Sheet 1 of 1
Scale: 1:60
Fax: [phone]
.sportsplayinc.com
Distributor: SportsPlay Inc
DateDra n By:
SportsPlay
SportsPlaySportsPlay
SportsPlay E. Barron 00-00-11
ASTM: Compliant
CPSC: Compliant
Project: 6' Ind. Spiral Slide
5642 Natural Bridge Size: 6' X 12'
Use Zone: 18' X 24'
Age Group: 5-12

18'
24'
800-727-8180
Sheet 1 of 1
Scale: 1:60
Fax: [phone]
www.sportsplayi c.com
Distributor: SportsPlay I c
DateDraw By:
SportsPlay
SportsPlaySportsPlay
SportsPlay E. Barro 00-00-11
ASTM: Complia t
CPSC: Complia t
Project: 6' I d. Spiral Slide
5642 Natural Bridge Size: 6' X 12'
Use Zo e: 18' X 24'
Age Group: 5-12
"52
45"
8"

Page 5
Tool and Material Checklist
•To dig holes, the best method is a tractor with an auger.
Use a 12” auger bit. No matter what you use, there will
be a considerable amount of hand digging as well
•Shovels, long handled spades
•Post hole diggers
•Wheelbarrows
•Large construction bar (generally 5’ long).
•Spray paint, to mark ground holes
•Pry bar
•Claw hammers
•Large dead-blow rubber hammers
•Small (3lb) Sledgehammer, to use in blocking the posts
•7/32”, 3/6”, 1/8” Allen wrenches: These are very
important. Several different types are helpful (socket
style, small “L” arm, wrench styles etc.)
•Vise grips, large, regular and needle-nose
•3/4” and 1/2” and 9/16” sockets, both 1/2” and 3/8”
drives
•6’ and 8’ stepladders, strong ones
•Extension cords (also duplexes to run more than one
cord)
•1/2” drill and 3/8” drill
•1/2” and 1/2” drill bits and 1/2” spade bits
•Levels: magnetic torpedo, 4’ long etc. (as many as
possible)
•Shims and blocks from scrap lumber and a saw to cut
sizes on site
•Small, skinny, flat shims are helpful in raising posts etc.
2” by 4” and 2” by 6” and Plywood are also helpful
•Pencils and markers
•String line
•Bar clamp 4’
•Sometimes bracing material is helpful (2” x 4” x 6’
studs with sturdy lag bolt/nut combinations)
•Files, sandpaper, wood scraps
•Stones
•Cement
•Surfacing
•One brick per post

Page 6
Introduction
BEFORE STARTING INSTALLATION OF YOUR
PLAYGROUND, PLEASE READ INSTRUCTIONS
THOROUGHLY.
SITE REQUIREMENTS:
The Playground system is designed to suit a level site. Should
there be any falls or slopes on the site; care should be taken to
accommodate the entry and exit points and to maintain the
correct height. There should not be more than 3” of drop in
grade per every 10’.
The site must be inspected for adverse conditions:
All sites must be checked for existing utilities such as
electricity, gas, water or any other underground hazards. 1-
800-DIG-RITE is the number to call to have the services
located.
1. Roots, rocks, or other natural obstacles that may pose as
a trip hazard.
2. Poor drainage areas.
3. Broken glass or foreign objects around building site.
MAINTENANCE:
As an owner, it is most important that you are aware of your
responsibility to insure safe use of your new equipment. It is
necessary to install equipment correctly according to the
installation instructions provided and inspect the equipment at
regular intervals. During inspection, if any part is found
damaged or excessively worn, equipment should immediately
be put out of service while the part is replaced. Lack of
maintenance will result in premature wear, reduced life
expectancy, and possible failure that might result in injury.
All SportsPlay Equipment play events have been engineered to
meet all applicable safety guidelines, but if installed
improperly, these problems may occur:
•Entrapment gaps (between 3 1/2” and 9”}
•String Entanglements
•Protrusions
Make sure that any bolt end that protrudes more than 2 threads
past the face of the nut is trimmed and deburred smoothly.
Always double-check your work.
Installation must adhere to the manufacturers assembly manual
and all other applicable safety guidelines.
PLAY AREA:
The area immediately above and around the play structure must
be free of any obstructions such as:
•Trees
•Other Play Equipment
•Buildings
•Overhead Power lines
Make sure the play area has all the required safety
surfacing and the minimum fall zones as required by the
safety guidelines. These guidelines can be found at
www.cpsc.gov.
CHILDREN MUST BE SUPERVISED AT ALL TIMES.
No playground is safe without adult supervision!

Page 8
CONCRETE – Mix the concrete according to the directions.
DO NOT mix directly in the hole. Fill each hole to within 2
inches of the original surface. Crown for drainage, and cure 48
hours.
SECURE AREA – Fence off or lock area to insure that NO
ONE can play on the playground until it is completely finished.
You may consider contacting local law enforcement to inform
them of the new installation and ask them to check the area
frequently during the night.
BACKFILL AND CLEANUP – 48 hours after pouring
cement, backfill all of the holes with dirt to the original ground
level and make sure the area is free of any tools, hardware, or
sharp objects.
SURFACING– Use the chart on page 8 to decide how much
safety surfacing is required. Before spreading loose fill
surfacing, be sure to install a weed barrier outside the fall zone
dimension, then spread the safety surfacing.
LAST THING– Make one more tour around the playground
and physically make sure all hardware is tight.
OPEN FOR PLAY– After the safety surfacing is installed and the
hardware has been checked for tightness, your playground is ready for
play.
MAINTENANCE -Consult your instruction booklet for the
maintenance checklist. Schedule and complete periodic
maintenance checks of the entire playground. If any hardware
is worn, or any item missing or broken, close the playground
and contact your SportsPlay distributor for replacement parts.
Check resilient surfacing depths, move or add additional
surfacing if necessary. Make sure the playground area remains
free of obstacles, broken glass or other sharp objects.

Page 9
Safety Surfacing/Fall Heights
You must consider the type of safety surfacing you will use
before beginning the installation process. There are two
general types, organic/loose fill or synthetic unitary. Both
materials have advantages and disadvantages and it is likely
that your client’s budget will dictate the material of choice.
Always have all options available as product quality and long-
term performance may cause your client to reevaluate their
original budget.
When installing a unitary safety surfacing material such as
rubber mats or poured-in-place, you will need to pour a
concrete slab so that the rubber material can be secured. This
type of product cannot be placed on dirt.
If a loose fill surface such as wood chips is selected, you will
need to consider containment borders. There are many
products to choose from including hard plastic and natural
products such as wood. Creosoted railroad ties are NOT
recommended. Loose fill materials like wood chips are easily
displaced, so 12” deep is generally satisfactory. Also
remember that loose fill will compress with repeated use.
Weed mat: Some use a landscaping fabric material that allows
drainage but prevents weed growth. Weed mats are installed
after the structure is installed but before the resilient surfacing
is installed.
Borders: Building borders above ground, below grade, or on
grade depends upon the area in which you live. Assuming you
must use 12” of resilient surfacing, there are three basic types
of installation:
1. 12” below existing grade
2. 6” below and 6” above existing grade
3. 12” above existing grade
The tallest deck on the unit generally defines the maximum fall
height of a structure. If upper body equipment (horizontal
ladder) is attached, the fall height is then the distance from the
highest part of the equipment to the protective surfacing. Refer
to the Top Down View to determine the maximum fall height.
Since the structure will be installed at dirt grade, the height of
the resilient surfacing must be determined and factored into the
height of installation of decks. For example, if the resilient
surfacing will be 12” deep, a 3’ deck height will actually install
at 4’. When the structure is completed and the surfacing is
installed, the deck then will be 3’ above the level of the
resilient surfacing.

Page 10
Safety Surfacing Chart
Table –Critical heights (in feet) of Tested Materials
These directions are written based upon a depth of 12” of
resilient surfacing.
Do not forget to calculate the compressed resilient surfacing
depth needed and adjust your “dirt grade height” accordingly.
Chart taken from The Handbook for Public Playground Safety
written by the U.S. Consumer Product Safety Commission
(CPSC) page 5 (www.cpsc.gov).
Material Uncompressed
Depths Compressed Depths
6” 9” 12” 9 “
Wood
Chips 4 10 11 10
Double
Shredded
Bark Mulch
6 10 11 7
Engineered
Wood
Fibers
6 7 >12 6
Fine Sand 5 5 9 5
Course
Sand 5 5 6 4
Fine Gravel 6 7 10 6
Medium
Gravel 5 5 6 5
Shredded
Tires 10- 12 N/A N/A N/A

Page 11
Punch List
Step 1: Layout
1. Lay decks on ground in the desired location based on
topview layout and measure from all corners to insure
there is adequate room. (Refer to Grid Drawing pg. 11)
2. Most installers usually like to orientate the playground
so that the entry point of the playground is facing either
the sidewalk or the direction from which the children
are coming.
Step 2: Holes
1. Mark the locations of all post holes by laying out all the
decks in the correct orientation. Make sure all the
decks are touching each other and flush on the edges.
Then use the center point of each deck corner and
marking them with paint or a wooden stake.
2. After the holes are marked, move the decks out of the
digging area and dig the first four holes per the footing
drawing on page 12.
3. Fill or dig the depth of 1 main hole to what is required;
this hole will be used to get the other three holes the
same depth in reference to each other. Make sure the
hole is flat and tamped solid, then place a small piece of
plywood or brick in the bottom. You must take this in
account when determining the hole depth.
4. Now, if possible, use a transit to maintain the same hole
depth on the remaining three holes, if you don’t have
access to a transit, then park a line on the first post
about two inches above the dirt level. Then measure up
from the bottom of the post to this mark and mark a line
on the other three posts at the same distance. Now use
a four-foot level across to each line, raising or lowering
as necessary to make the lines level. Repeat this for the
remaining two posts.
Step 3: Deck and Post Installation
1. Begin by installing the lowest deck and go up from this
one. Measure deck height plus the amount of safety
surfacing and make a mark on the post, this is the
height of the deck clamps, for example if the deck is to
be 36” high and you are planning on adding 12” of
safety surfacing then the height from the dirt would be
48”. All other decks heights will also be the labeled
height plus the amount of surfacing.
2. Install a deck clamp per instruction page 15. Tighten
all hardware.
3. Now make sure that you have two other helpers and the
required deck clamp hardware.
4. Stand the correct posts into the holes and lift the deck
on top of the clamps and install hardware. Be sure to
brace the posts to keep them from moving.
5. Continue building the main structure by adding the
overhead climber, kickplates and other decks and posts
per the illustration until all the decks, kickplates, and
posts are installed. Make sure the posts are level as you
tighten the hardware, this will make the component
installation much easier.
6. It may be necessary to brace the deck and posts with
lumber to make sure they stay in place and level. Also
make sure the deck was installed level.

Page 12
Step 4 –Component Installation
1. Begin installing the components by working from the
lowest deck around to the highest deck. Install the
components in either a clockwise or counter clockwise
rotation.
2.
Step 5: Concrete
1. Once all components and posts are tight and level, you
may concrete. A good rule of thumb is two 80 lb. bags
of concrete per hole. Do not “dry bag” the concrete,
always mix per instructions on concrete bag. Be sure to
leave concrete about 2” from the top of the ground to
allow backfill.
2. Be sure that all splattered concrete is washed off of the
posts and components while it is still wet.
3. Block off installation area for at least 48 hours.
Step 6: Final after 48 hours
1. Return in 2 days to backfill concrete, drill and install
drive (roll) pins per instructions, and install safety
surfacing.
2. Inspect all components to insure the hardware is tight
and all panels are level.
3. Make sure all tools and dropped hardware are removed
from play area.
4. Open the playground.

and the height of the brick.
Footing depth should be 22"
Refer to CPSC Guide for
on Depth:www.cpsc.go
Surfacing Recommendations
2"
Backfill
12"
Sheet 1 of 2
Sheet 1 of 2Sheet 1 of 2
Sheet 1 of 2
Concrete
Surfacing
Ground Co er
Backfill
Playground
Soil
Natural
Finished
Brick
Post
Side View of installed Post
Side View of installed PostSide View of installed Post
Side View of installed Post
1
5432
3.5" Post Footing

Sheet 2 of 2
Sheet 2 of 2Sheet 2 of 2
Sheet 2 of 2
line.
conditions. Base of fooing MUST be below the frost
Footing size may vary due to local soil and weather
Post nstallation:
Post nstallation:Post nstallation:
Post nstallation:
not dug on center.
easier.
Post tops should be level with one another.•
USE A LONG, HEAVY CONSTRUCT ON BAR to•
adjust levels of posts, legs, etc. DO NOT try to level
by pushing posts at shoulder or waist length. Carefully
bump the posts at the bottom N THE D RECT ON
YOU WANT THE POST TO GO.
Mark holes and dig by laying the deck on ground•
and using it as "jig". Place (4) deck clamps, one per
corner, spray paint though middle of clamp onto
ground. This marks where the centers of the postholes
should be.
nstall the red plastic ends caps on post bottoms.•
Dig holes straight down, with a flat bottom and 12"•
wide making sure to dig holes wide and not cone
shaped.
Hole depths are 22" deep
Hole depths are 22" deepHole depths are 22" deep
Hole depths are 22" deep plus blocking.(this depth •
changes slightly with grade).
Place a brick or block in the bottom of the hole. Post
PostPost
Post•
••
•
Depth in concrete varies based upon surfacing
Depth in concrete varies based upon surfacingDepth in concrete varies based upon surfacing
Depth in concrete varies based upon surfacing
used. (see side view of installed post)
used. (see side view of installed post)used. (see side view of installed post)
used. (see side view of installed post)
Post is placed on top of the brick.•
f the bottom is not flat and roomy, there will be no•
room to adjust. t is much easier to have too much
room rather than not enough.
You can dig by hand using a posthole digger but•
a tractor with a 12" auger will make the task much
Remove the deck and clamps from the area.•
Block the posts into center of holes when posts are on•
bubble. Use scrap lumber and wedge to solidify the
posts in their holes as you level the posts. Re-blocking
may be necessary at times in order to acheive level.
You may also have to widen your holes if they are
Top down view of post set into hole.
Top down view of post set into hole.Top down view of post set into hole.
Top down view of post set into hole.
1
5432
3.5" Post Footing

A
AA
A
Detail A
1
2
3
Sheet 1 of 2
Sheet 1 of 2Sheet 1 of 2
Sheet 1 of 2
ITEM NO.
SQUARE DECK 912-334
SQUARE DECK 912-334SQUARE DECK 912-334
SQUARE DECK 912-334
TRIANG E DECK 912-333
TRIANG E DECK 912-333TRIANG E DECK 912-333
TRIANG E DECK 912-333
PART
NUMBER DESCRIPTION QTY.
1 905-903 Square Deck 1
2 126-703 3/8" x 1" Button Head Bolt 8
3 316-601 3/8" Flat Washer 8
ITEM NO. PART
NUMBER DESCRIPTION QTY.
1 905-904 Triangle Deck 7
2 126-703 3/8” x 1” Button Head Bolt 1
3 316-601 3/8” Flat Washer 1
21
SQUARE AND TRIANG E DECKS
SQUARE AND TRIANG E DECKSSQUARE AND TRIANG E DECKS
SQUARE AND TRIANG E DECKS
543
912-333
912-333912-333
912-333
912-334
912-334912-334
912-334

Deck Plan:
Deck Plan:Deck Plan:
Deck Plan:
found on the Top Down View.
Sheet 2 of 2
Sheet 2 of 2Sheet 2 of 2
Sheet 2 of 2
The deck(s) connect to the main upright posts using nuts
factory installed in the post according to the specifications
NSTRUCT ON:
NSTRUCT ON:NSTRUCT ON:
NSTRUCT ON:
Event: Steel Decks are constructed of 12 ga. perforated
steel.
Paint: Oven cured plastisol.
Hardware: Stainless steel tamper resistant.
MA NTENANCE:
MA NTENANCE:MA NTENANCE:
MA NTENANCE:
Touch up any marred paint surfaces.
Periodically check hardware for integrity and tightness.
These are two methods:
The BEST method is to make a table or stand to place
your deck on at the required deck height. The table will
stabilize the deck so you can level it.
You can make a table from sawhorses.
Deck stand or table holds deck while you build around
it.
Block stabilize the posts while table stabilizes the deck.
The second method is to use two people to hold the deck
at the required height and attach the bolts through the
deck to the post. The decks bolts directly to the post
through the factory installed riv-nuts. Use the 3/8" x 1"
button pinned stainless steel bolts with a washer through
the holes in the corners of the decks. There are two holes
in each corner to bolt through. The deck and posts will
stabilize more as you add components.
SPEC F CAT ONS:
SPEC F CAT ONS:SPEC F CAT ONS:
SPEC F CAT ONS:
4321
SQUARE AND TR ANGLE DECKS
SQUARE AND TR ANGLE DECKSSQUARE AND TR ANGLE DECKS
SQUARE AND TR ANGLE DECKS
5
912-333
912-333912-333
912-333
912-334
912-334912-334
912-334

1
3
C
CC
C
See TABLE
TABLE
See
4
10 316-601 3/8" Flat Washer 20
11 226-602 3/8" Nylon Lo k Nut 6
12 126-701BPS 3/8" x 1-1/4" Button Head Bolt 10
ITEM NO. PART
NUMBER DESCRIPTION QTY.
1
905-707
905-708
905-709
905-712
Step Ladder 3'
Step Ladder 4'
Step Ladder 5'
Step Ladder 6'
1
2 903-306 Ar h Entry Panel 1
3
903-323
903-235
903-326
903-327
Handrail 3'
Handrail 4'
Handrail 5'
Handrail 6'
2
4 903-324 Step Leg 1
5 913-401 2 Hole Atta hment Bra ket 2
6 196-807 3/8" x 3/8" So ket Set S rew 6
7 905-208 Gasket for Atta hment Bra ket 2
8 905-526 1/4" Self Tapping Pinned S rew 4
9 126-708 3/8" x 2-1/4" Button Head Bolt
Table
TableTable
Table
De k
Height
Post/Footing
Distan e
36" 27"
48" 34"
60" 41"
72" 55"
10 9
10
13
11
Sheet 1 of 2
Sheet 1 of 2Sheet 1 of 2
Sheet 1 of 2
Detail C
4
Detail E
A
AA
A
2
B
BB
B
E
EE
E
D
DD
D
5
"45
20"
321
STEP LADDER 3', 4', 5', 6'
STEP LADDER 3', 4', 5', 6'STEP LADDER 3', 4', 5', 6'
STEP LADDER 3', 4', 5', 6'
54
912-323, 902-234,
912-323, 902-234,912-323, 902-234,
912-323, 902-234,
912-235, 912-326
912-235, 912-326912-235, 912-326
912-235, 912-326
Detail A
11
Detail D
12
1
10
De k
10
12 10
1
4
11
6Detail B
8
2
5
7
Post 26
3

•
coat.
Sheet 2 of 2
Sheet 2 of 2Sheet 2 of 2
Sheet 2 of 2
Hardware: Stainless steel tamper risistant.
Tighten until lock nut is flush with thread end of bolt.
ladder, and fasten with 3/ " lock nut.
bolts, no washer on the inside of the ladder, through
and tighten. Fasten top portion of handrails with 3/ "
See the Top Down View for placement.
• Make sure arch entry clamps are level to each other
MAINTENANCE:
MAINTENANCE:MAINTENANCE:
MAINTENANCE:
Step Ladder Plan:
Step Ladder Plan:Step Ladder Plan:
Step Ladder Plan:
• Connect these with (4) 3/ " x 2-1/4" button head
holes in the bottom side of stepladder.
x 3/ " set screw.
•
SPECIFICATIONS:
SPECIFICATIONS:SPECIFICATIONS:
SPECIFICATIONS:
The Step Ladder connects to 3', 4', 5', and 6' deck top
and bottom angle connection to deck and ground with
ground legs. Arch entry wall is 1-3/ " OD steel with 2
attachmet brackets to connect
INSTRUCTIONS:
INSTRUCTIONS:INSTRUCTIONS:
INSTRUCTIONS:
Temporarily lay the angle-lip of stepladder onto deck•
so that there is a 90- degree connection. Center it over
the 15" appart holes on top of deck.
Mark holes on the ground for the two bottom legs•
(20" apart).
Remove ladder and dig two holes 12" wide and 24"•
deep.
Connect the bottom leg with (2) 1-1/4" x 3/ " button•
head bolt, washer on top and lock nut on bottom.
Install (2) re-bar in bottom leg pipes and install•
assembly into ground holes.
Tip up to deck and connect to deck holes (on top of•
deck) with (2) 3/ " x 1-1/4" button head bolts, one
washer on top and one on bottom, and lock nut.
Connect the arch entry to the center of the posts•
with (2) attachments brackets with gaskets between
the post and bracket. Then to the deck on the bottom
through the plates.
Connect the left and right handrails so that the top•
end (end with no holes) goes into the pipe sleeves
on the arch entry.
Line up the bottom of the handrail (2 per side) to the
Event: Steps have a 7-1/4" step and -1/2" riser made of
#9 ga.
Entire ladder is PVC coated after fabrication.
Paint shall be electrostatically applied oven cured powder-
Touch up any marred paint surfaces.
Periodically check harware for integrity and tightness.
1
STEP LADDER 3', 4', 5', 6'
STEP LADDER 3', 4', 5', 6'STEP LADDER 3', 4', 5', 6'
STEP LADDER 3', 4', 5', 6'
5
4
3
2
912-323, 902-234,
912-323, 902-234,912-323, 902-234,
912-323, 902-234,
912-235, 912-326
912-235, 912-326912-235, 912-326
912-235, 912-326

B
BB
B
Detail B
3
1
5
4
A
AA
A
2
C
CC
C
45"
ITEM NO. PART
NUMBER DESCRIPTION QTY.
1 435-623 6 Spiral Slide 1
2 905-910 Transition Deck 1
3 912-431 Wall for Spiral Slide 3.5" 2
4 913-402 4 Hole Attachment Bracket 4
5 905-911 12" Kick Plate 1
6 905-208 Gasket for Attachment Bracket 4
7 126-705 3/8" x 2" Button head bolt 4
8 516-200 3/8" Toggler 16
9 126-707BPS 3/8" x 1-1/2" Button head bolt 2
10 126-704 3/8" x 3" Button Pin Bolt 4
11 226-601 3/8" Nylon Lock Nut 8
12 196-807 3/8" x 3/8" Socket Set Screw 4
13 126-701 3/8" x 1-1/4" Button head bolt 8
14 126-703 3/8" x 1" Button head bolt 4
15 316-601 3/8" Flat Washer 30
16 903-201 Spiral Slide Filler Angle 2
17 905-526 1/4" Self Tapping Pinned Screw 8
11
11
15
15
5
13
15
13
15 Detail A
6
4
3
?
12
Sheet 1 of 4
Sheet 1 of 4Sheet 1 of 4
Sheet 1 of 4
1
6 SPIRAL SLIDE
6 SPIRAL SLIDE6 SPIRAL SLIDE
6 SPIRAL SLIDE
5
4
3
2
912-282
912-282912-282
912-282

FOOTING DIAGRAM
FOOTING DIAGRAMFOOTING DIAGRAM
FOOTING DIAGRAM
1
3
10
8
DETAIL E
Typ 4 Pls
Typ 2 Pls
DETAIL F
20
17
2
5
17
18
DETAIL D
Typ 4 Pls
"52
45"
8"
912-282
912-282912-282
912-282
54321
SPIRAL SLIDE t 6' DECK
SPIRAL SLIDE t 6' DECKSPIRAL SLIDE t 6' DECK
SPIRAL SLIDE t 6' DECK
SHEET 2 f 2
SHEET 2 f 2SHEET 2 f 2
SHEET 2 f 2
1
9
21
8
8
1
DETAIL C
Typ 4 Pls

face of the entry area.
next day or if it seems stable you can begin installing
Sheet 3 of 4
Sheet 3 of 4Sheet 3 of 4
Sheet 3 of 4
also from the sides. The only true are to level is the
level between the post looking at it from the front and
INST UCTIONS:
INST UCTIONS:INST UCTIONS:
INST UCTIONS:
Begin by marking the four hole locations which need
at the top of the guard wall.
Once level you can either concrete and come back the•
5' Spiral Slide Plan:
5' Spiral Slide Plan:5' Spiral Slide Plan:
5' Spiral Slide Plan:
filler angel to prevent any string entrapments from forming
a transition platform and 2 guardrails. It also contains a
The Spiral Slide attaches to the main structure deck via
•
to be drilled in the face of the slide, these are used
for attaching the slide to the transition platform. The
narrow end of the transition platform should be facing
the slide entry and then the top of the platform will rise
up to the small lip located just at the base of the slide
entry. Center the platform on the slide and mark the
four holes. These holes need to be drilled with a 3/4"
drill bit and then the 3/8" toggler bolts will install in
them.
Mark hole location based on footing diagram and dig•
a hole 18" in diameter and at least 24" deep (the
deeper the better, slide can be blocked to the
correct height).
Attach the transition deck to the posts, brace up on•
outer end on level and tighten hardware through deck
to post.
Next make sure the center support post is locked as •
far up in the slide as possible and with the help of
at least two other people lower slide into the hole.
Now level the slide front to back and side to side,•
sometimes this can be difficult to do because of the
variances in the slides so also make sure it "looks"
the guardrails. This will be determined by how much
blocking was needed to raise the slide up.
Begin installing the guard walls by attaching the rails •
to the slide. Make sure the rails are running in line
with the deck and the end holes on the rails are
about 1-1/2" from the outer edge of the slide.. Mark
the four holes then rotate the rails out from the slide
and drill them with 3/4" drill bit and insert the 3/8"
togglers. Be sure to maintain no more than 3-1/2"
gap between the bottom of the rails and the top of
the transition platform.
Install bolts through the rails and into the slide and •
tighten all hardware.
Attach the rails to the post using the four 4 hole•
attachment brackets with gaskets between the
brackets and the posts. Attach the brackets using
the self tapping screws. Make sure to tighten set
screws on the brackets first to keep the brackets
from spinning when attaching to the post.
Install filler angle by marking the hole location which•
needs to be drilled in the face of the slide, using the
slide filler angle. The filler angle should be positioned
on the inside of the wall so that the gap between the
top of the Guard Wall and the Spiral Slide is
blocked, and the Spiral Slide as well. These holes
need to be drilled with a 3/4" drill bit and then the
3/8" toggler will install in them. Do not over tighten
the toggler for they will break easily.
Once the toggle is installed attach the filler angle •
using the 3/8" x 1-1/2" bolt with washer. epeat
this step for the other guard wall as well.
1
6' SPI AL SLIDE
6' SPI AL SLIDE6' SPI AL SLIDE
6' SPI AL SLIDE
5
4
3
2
912-282
912-282912-282
912-282

1
6' SPIRAL SLIDE
6' SPIRAL SLIDE6' SPIRAL SLIDE
6' SPIRAL SLIDE
5
4
3
2
912-282
912-282912-282
912-282
MAINTENANCE:
MAINTENANCE:MAINTENANCE:
MAINTENANCE:
powdercoat.
S eet 4 of 4
S eet 4 of 4S eet 4 of 4
S eet 4 of 4
Hardware: Stainless steel tamper resisitant.
SPECIFICATIONS:
SPECIFICATIONS:SPECIFICATIONS:
SPECIFICATIONS:
Event: Slide is rotaitionally molded and deck is plastisol
coated.
Paint s all be electrostatically applied oven cured
Touc up any marred paint surfaces.
Periodically c eck ardware for integrity and tig tness.