SportsPlay 902-795 User manual

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
1

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
2
TOP DOWN VIEW
SIDE VIEW

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
3
PANEL 1
PANEL 2
PANEL 3
PANEL 4
PANEL 5
PANEL 6
PANEL 7
PANEL 8
Bird/

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
4
PANEL 9
PANEL 10
PANEL 11
PANEL 12
PANEL 13
PANEL 14
PANEL 15
PANEL 16
PANEL 17
PANEL 18

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
5
PANEL 20
PANEL 21

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
6
DECK 1 & 2
DECK 3
DECK 4

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
7
DECK 5
SLIDE
2 POINT FIT
3 POINT “L” FIT
3 POINT STRAIGHT
4 POINT T FIT

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
8
Keep these instructions on file. Contact your distributor for
replacement parts
Adult supervision is required at all times!
Maintenance/Inspection
•Visual inspection is recommended prior to each use.
•Inspect all strings, nets, decks, graphic banners, mats,
accessories and the slide for loose, torn or broken parts. If
damage is present you must repair or replace that component to
prevent further damage or injury to the user. Contact your
distributor to order replacement parts.
•Ensure all connector fittings are in place and properly seated
into play panels.
•Ensure slide is installed tightly.
SHOULD A COMPONENT BECOME DAMAGED YOU MUST
CLOSE THE UNIT TO PLAY UNTIL THE REPAIRS ARE MADE!
In order to prevent injury to personnel and damage to components a
minimum of two people are required to lift all panels, decks and the
slide.
To prevent damage during install all components should be placed on
a protective surface (cardboard, plastic sheet or tarp) and not placed
directly on the ground while they are being sorted.
It is recommended that users take their shoes off before entering the
play equipment.
Trouble Shooting
•Dimensions listed in the drawings above will vary up to +/- 1”
because of the padding.
•The connector fittings with the threaded rod welded on top are
used to connect the junction of panels 1 and 2 to the junction of
panel 8 and 7 using the round connection shaft included.
•Panels 5 and 9 have the standard net as well as a secondary net
required for the slide area.

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
9
LAYOUT VIEW

902-795 JUNGLE CONTAINED PLAY
INSTALLATION INSTRUCTIONS
WWW.SPORTSPLAYINC.COM
10
Us the drawings of the panels and decks to identify each component
and use the layout view to identify their proper location.
Since some of the panels have the same dimensions further
information is needed to identify them:
•Panel 1 – graphic at the bottom of the panel is a bird.
•Panel 2 – graphic at the bottom of the panel is a rabbit
•Panel 3 – graphic at the bottom of the panel are two monkeys
(the graphic on panel 3 is larger than the graphic on panel 6
which also has two monkeys)
•Panel 4 – graphic at the bottom of the panel is a squirrel
WHEN INSTALLING THE CONNECTION FITTINGS BE SURE
TO INSTALL THE BOTTOM FITTING FIRST THAN THE PANEL
AND FINALLY THE TOP FITTING.
USE THE LAYOUT DRAWING TO IDENTIFY THE PROPER
CONNECTION FITTING TO USE. NOTE HOW THE PANELS
OVERLAP EACH OTHER AT THE CORNER TO IDENTIFY THE
REQUIRED FITTING
Panel 1 and 2 represent the front of the unit while panels 20 and 21
represent the back of the unit.
All detail drawings are located at the end of this instruction
booklet.
There are three sizes of spindles – small, medium and large.
Installation Instructions
1. Install the required connection fittings into the bottom of panel.
The graphic should be facing away from the unit. (refer to
detail 1 at the end of this instruction book.
2. Slide panel 2 onto the fitting it shares with panel 1 and the
other bottom fitting it shares with panel 3. THIS STEP
REPEATS THROUGHOUT THE PROJECT.
3. Insert the special fitting (one of the fittings with the threaded
rod welded to the top) at the top where panels 1 and 2 meet.
(This rod connects this point to the junction or panels 7 & 8
using the included connection tube. See Detail 2 at the end of
this instruction booklet)
4. Install panels 3 and 4 using the layout view for proper
placement.
5. While referring to the layout drawing install the following
panels in order:
a. 7 (graphic at the bottom of panel 7 should face towards
the back of the unit) & 8
b. 5, 9 & 6
6. Install the slide by inserting the tabs welded on to the slide in
to the pockets attached to panels 9 and 5 (Detail 3). In order to
verify proper installation the slide should slope down towards
the front of the unit.
7. Install the connection rod at the junctions of panels 1 & 2 and
panels 7 & 8. (Detail 2)