squarespace CL-TYH-3W User manual

www.stellarlighting.co.uk
email: [email protected]
1
CL-TYH Solar outdoor motion-sensor wall light
User manual
Technical specification
Model
CL-TYH-3W
Main features
Motion-sensor activated, wireless, solar outdoor light with daylight sensor
Battery
3.2 V - 1500 mA Lithium battery (solar-charged)
Solar panel type
Monocrystalline, 5.5 V,0.6 W
Power
3 W
Light source type
SMD 2835 white LED
LED quantity (pcs)
24
CRI (Ra>):
>80
Outdoor use
Yes, suitable for outdoor use
Light colour
White 3000 K / 4000 K / 6000 K
Luminous flux
280 lm +/- 10%
Light angle
120°
Sensor type
PIR sensor
Daylight sensor sensitivity
10 LUX
Detection range
3 6 m
Detection angle
120°
Operation mode
3 operation modes
Blocking time
0.2 sec
Operation time
≥2.6 hours
Charge time
4 hours
Operating temperature
-10°C - 40°C (25°C is the most optimal)
Material & colour of housing
ABS + PC (White colour)
Product size
97 x 123 x 46 mm
Lifetime
50,000 hours
Warranty
2 years
Package dimensions
127 mm (L) x 50 mm (W) x 103 mm (H)
Weight with packaging
0.167 kg

www.stellarlighting.co.uk
email: [email protected]
2
CL-TYH Solar outdoor motion-sensor wall light
User manual
Safety notices
Electrical work safety advice and tips
●Keep away from inflammable and explosive materials when charging. The charging time should not
exceed 12 hours. Try to avoid using while charging.
●Avoid placing the light in the rain, outdoors or in moist areas as it may damage or short-circuit the
device.
●Do not place the product into fire, open flame or hot surface as it may cause combustion or explosion.
●Do not open the LED light forinspection or re-wire the electronic circuits ifyou are not a professional.
Opening the light engine might void your warranty.
●Avoid any debris on top or around the light engine as it can cause poor heat dissipation.
●Avoid using the device under -10°C and above 40°C temperature.
DIY tips and safety advice
●This task will involve working at height. A safe system of work should be established and maintained, in
order to prevent injury.
●Consider your safety! Think about the potential risks and dangers of the work and the steps you should
take to avoid them.
●Personal protective equipment. Make sure that you are equipped with suitable and sufficient personal
protectiveequipment.Thiscouldincludeeye protection,facemask,protectiveoveralls,safetyfootwear
and gloves.
●Ensure that the work area is sufficiently illuminated.
●Check that the tools you will be working with are in a good operating condition. For the installation,
you will need a cordless drill with drill bits or a screwdriver.

www.stellarlighting.co.uk
email: [email protected]
3
CL-TYH Solar outdoor motion-sensor wall light
User manual
Product details
Sensing range
Product dimensions
Solar panel
Mounting hole
PIR sensor
Mode button
LED panel

www.stellarlighting.co.uk
email: [email protected]
4
CL-TYH Solar outdoor motion-sensor wall light
User manual
Installation
1. Drill the hole for the raw plug and screw in the screw,leaving the screw head partially protruded
Step 1: Drill the hole for the raw
plug
Step2: Screwinthe screw,leaving
the screw head partially protruded
Step 3: Hang the light
Operation
•
•At night time, when the brightness drops under 10 LUX, the solar panel stops charging and the light
enters into work mode.
•button again for 3 seconds to switch the light off.
•circulate between the three operation modes. The light will flash up
1x, 2x or 3x indicating the current mode.
oMode 1: Motion-sensor mode with dimmed constant light
▪The lamp will automatically light up and enter warm-up status; the warm-up time is
about 10 seconds. After the warm-up time, the lamp enters into a dimly lit state. When
themotionsensoristriggered(4-6mrange),theactivitylightturnsontofullbrightness
for 30 seconds. If the sensor senses activity after 30 seconds, the light remains on for
enters back into dimmed state.
oMode 2: Motion-sensor mode
▪The lamp will automatically light up and enter warm-up status; the warm-up time is
about 10 seconds. After the warm-up time, the lamp switches off. When the motion
sensor is triggered (4-6 m range), the activity light turns on to full brightness for 30
seconds. If the sensor senses activity after 30 seconds, the light remains on for another
30seconds.Ifthe
off.
oMode 3: Constant light mode
▪The light remains on for 4 hours.
•Once a mode is set, the device saves the setting in its memory, until it is manually changed.

www.stellarlighting.co.uk
email: [email protected]
5
CL-TYH Solar outdoor motion-sensor wall light
User manual
Application areas
The CL-TYH Solar outdoor motion-sensor activated wires outdoor lights have a wide range of applications:
street, courtyard, gate, balcony, garage, garden. All you need is a surface to secure the lights to.

www.stellarlighting.co.uk
email: [email protected]
6
CL-TYH Solar outdoor motion-sensor wall light
User manual

www.stellarlighting.co.uk
email: [email protected]
7
CL-TYH Solar outdoor motion-sensor wall light
User manual