Volt BuddyPro Plus VHS-67 BRB Series User manual

VOLT®Low Voltage Landscape Lighting
VOLT® Hardscape Puck Light
VHS-67XX-X-BRB
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2020, VOLT®Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®Hardscape Puck Light
VHS-67XX-X-BRB
INSTALLATION INSTRUCTIONS
www.voltlighting.com
Important: Please Read Before Installation
Important Safety Instructions
!
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.voltlighting.com or call 1-813-978-3700.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
- 2 -

VOLT®Hardscape Puck Light
VHS-67XX-X-BRB
Package Contents
A. (1) Fixture
Product Dimensions
0.625”
1.5”
Surface Mounted
1
Anchor
(optional)
Puck Light
Surface
Lock Screw
Attach the puck light to the at surface
(under railings, shelves, counters,
benches, or any other niche location).
Secure with lock screws.
Note: Wall anchors are required for
certain installation conditions (brick
and/or concrete surfaces). Place a mark
on the surface where the holes are
located on the puck light. Remove the
puck light and drill proper holes on the
at surface, then insert the anchors.
*** NOTE***
FIXTURE MUST BE MOUNTED IN AN
INVERTED POSITION - FACING DOWNWARD
[email protected] • 813.978.3700
1.5”
- 3 -

INSTALLATION INSTRUCTIONS
www.voltlighting.com
VOLT®Hardscape Puck Light
VHS-67XX-X-BRB
Lay the supply cable out from the transformer. Strip both leads from
the luminaire pigtail. Connect the leads from the luminaire supply
cable to the transformer (sold separately).
Pigtail
Transformer
(sold separately)
Supply Cable
1.5” Hole
Lock Screw
Anchor
(optional)
Recessed Mounted
2
Wire Connections
3
Using a 1.5” core drill bit, drill a hole in
the desired at surface. Attach the puck
light into the drilled hole and secure
with the lock screws.
Note: Wall anchors are required for
certain installation conditions (brick
and/or concrete surfaces). Place a mark
on the surface where the holes are
located on the puck light. Remove the
puck light and drill proper holes on the
at surface, then insert the anchors.
Puck Light
Puck Light
- 4 -