SRS Light Design DSR10N User manual

Technical data
Main:
Transformer: 230 V / 50 Hz
Transformer: 110 V / 60 Hz on request
Switching PS : 89-265V / 50-60Hz on request
Input/ Output:
SITT DMX512, ANSI E1.11 – 2004 for RJ45
Size:
1 , 19 inch format / 482,5 x 44,5 x 130 mm
Weight:
2,1 kg
Shipment consists of:
DSR10N, IEC or PowerCON cable, Printed manual
Warranty:
If there is any problem just send us an email to [email protected] or call us and
be calm because your device has lifetime warranty and you’ll receive the
replacement equipment for free.
DEC ARATION OF CONFORMITY
According to a guidelines 89/336 EEC and 92/31 EEC:
Name of producer: SRS Light Design s.r.o.
Address of producer: Rybnicna 36/D, SK- 83106 Bratislava, Slovak Republic
Declares that the product
Name of product: 10 way DMX splitter
Type: DSR10N
Corresponds to the following product specifications:
Safety: EN60065, resp. EN 60950
EMC: EN55103-1, resp. EN55103-2
Additional information:
nit and all connected apparatus must be earthed via main cable.
Bratislava, 10
th
of may 2009
Robert Sloboda
SRS L
SRS LSRS L
SRS Light Design
ight Designight Design
ight Design, Rybničná 36/D , 831 06 Bratislava, Slovakia, tel: [phone],
fax: [phone], www.srslight.sk , [e-mail]
10 way DMX splitter
Instruction Manual
Model:
DSR10N: RJ45 connectors
DSR10N-3 : 3pin/RJ45 DMX connectors
DSR10N-5 : 5pin/RJ45 DMX connectors
ATTENTION!
This instruction manual contains important information about the
installation and use of equipment. Please read and follow these
instructions carefully.
Always ensure that the power to equipment is disconnected before
opening the equipment or commencing any maintenance work.

SRS L
SRS LSRS L
SRS Light Design
ight Designight Design
ight Design, Rybničná 36/D , 831 06 Bratislava, Slovakia, tel: [phone],
fax: [phone], www.srslight.sk , [e-mail]
IMPORTANT SAFETY INFORMATION
The following general safety precautions have to be observed during all phases of
operation, service, and repair of this equipment. Failure to comply with these
precautions or with specific warning in this manual violates safety standards of
design, manufacture, and intended use of this equipment.
Do not operate in an explosive atmosphere
Do not operate this equipment in the presence of flammable gases or fumes.
Operation of any electrical instrument in such an environment constitutes a definite
safety hazard.
Water, moisture, heat and humidity
Do not operate this equipment near water or in areas with wet floors, also not in high
humidity atmosphere where condensation forms on the equipment. It should never
be placed near or over heat register or other source of heated air and it should not
be installed or operated without proper ventilation.
DMX connections
DMX 3/5/RJ45 XLR connectors are located on front panel of device. These are
separated to two groups. 1
st
group is wired 1:1 and marked as IN and O T. This line
should be terminated by the termination switch marked T. When line is terminated by
120R resistor the red LED T. indicator is on.
The 2
nd
part of splitter consists of 10 way optically isolated lines marked with
numbers 1 - 10. Each line have separate power supply and line driver + indication of
signal on the both signal lines wit two LEDS marked as 2, 3.
Pin 1 Ground / Common
Pin 2 Data -
Pin 3 Data +
Pin 4, 5 NC
Pin 1, 3 Data+
Pin 2, 6 Data -
Pin 4, 5 NC
Pin 7, 8 Ground / Common
SRS L
SRS LSRS L
SRS Light Design
ight Designight Design
ight Design, Rybničná 36/D , 831 06 Bratislava, Slovakia, tel: [phone],
fax: [phone], www.srslight.sk , [e-mail]
Controls and indication
1. DMX input signalization
2. DMX input/output connectors
3. Termination switch
4. DMX output signalization
5. DMX output connector
Device Design
Front panel:
Rear panel:
Device use/servicing:
By default without any incoming signal there are all LEDS off and the ON LED
indicator indicates the device is on main power. The T. termination LED is ON when
the termination switch is activated.
When you connect the DMX cable to device, all LED marked as 2 / 3 or sign of signal
polarity goes ON and this indicates that DSR10N is functioning properly and
retransmitting the input to the splitted outputs. If there is any LED off check the
cable first – if there is short circuit on line the respective LED is off.