SSV Works WP-A360S4 User manual

WP-A360S4
360 Watt Amplier
SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
www.SSVworks.com | Phone: [phone] x2 | Fax: [phone]
!
Please read and understand these
instructions completely before
installation to avoid possible injury, or
damage to the accessory or vehicle.
WARRANTY INFORMATION:
All SSV Works ampliers are covered by a limited 1 year warranty against defects in material or
workmanship. All SSV Works electronics are covered by a limited 1 year warranty against defects in material
or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for
further warranty information.
TOOLS NEEDED FOR
INSTALLATION AMPLIFIER SPECIFICATIONS
INSTALLATION NOTES
CROSSOVER
CONFIGURATIONS
RECOMMENDATION 1 (120hz CROSSOVER)
RECOMMENDATION 2 (80hz CROSSOVER)
- P2 screw driver
- P1 screw driver
- Class D, 4 Channel
- Low Level Inputs
- Output 4 ohm, 50Wx4
- Output 2 ohm, 90Wx4
- Drill
- 1/8” Drill bit
- BTL Output 4 ohm,
200W x 2
- Selectable
Hi-Pass lter
60/100/120 Hz
SSV Works WP Series ampliers are designed with weather-proof durability and Plug and Play harnessing.
The WP-A360s4 amplier is pre-tuned for SSV Works Source Units, which provides the best output levels
with no distortion.
1. Remove the 4 screws
securing the plate to
gain access to the dip
switches.
2. Use a small screwdriver
to ip the switches up or
down.
3. Switches 1 and 2 work
together to adjust your
FRONT crossover point.
4. Switches 3 and 4 work
together to adjust your
REAR crossover point.
5. Switch 5 adjusts your
amplier between 2 or 4
Channel input mode.
120hz crossover on both front and rear speakers is recommend
when adding a subwoofer in addition to your system.
POWER / PROTECT LED LIGHT
Blue LED indicates the amplier is powered up and in working order.
RED LED indicates protect mode is enabled on the amplier
Protect Mode:
Protect mode can indicate:
Amplier is overheating:
- Improper impedance
- Not enough ventilation
Short circuit:
- Speaker wires are making contact with each other.
Low Voltage:
- Amplier needs 10-16 volts in order to operate.
80hz crossover on both front and rear speakers is recommend
when no added subwoofer will be part of the system.
© 2016 SSV Works, Oxnard, CA 93030 WP-A360S4 Rev. D 7-1-16
WP-A360S4
1
1
2
2
3
3
4
4
5
5
REMOVE PLATE

INSTALLATION SPEAKER OUTPUT
POWER INPUT
SIGNAL INPUT
ADJUSTING AMPLIFIER INPUT GAIN CONTROLS
AMPLIFIER WIRING DIAGRAM
LOCATION:
• When choosing a location to mount your
amplier, be sure to mount on a solid surface.
• Stay clear of any wires that may be routed
underneath the amplier.
• Pick a well ventilated area to avoid
overheating.
WP-A360s4 speaker outputs
come with plug and play
connectors to quickly adapt
to SSV Works vehicle wiring
harnesses.
If you will not be using an SSV
Works vehicle specic wiring
harness, you may contact SSV
Works for a universal harness.
The power input has been pre-terminated to
work with SSV amplier wiring kits. Red and
Black wires have been used to identify power
and ground.
*If you are not using an SSV Works amplier
wiring kit please refer to the chart to identify the
power and ground wires. You may contact SSV
Works for a universal wiring kit.
The low level inputs are pre-terminated into SSV specic connectors, this allows you to quickly adapt to
any of SSV source units.
The WP-A360s4 has been tuned to match SSV Works source units. If you are using a non SSV Works source
you unit follow the instructions below to adjust the input gain settings.
Note: If you are using an SSV Works source unit disregard the steps below.
1. Once you have connected power and speakers to your amplier you are now ready to adjust the
input gains.
2. On the signal input side of the amplier, remove the 4 screws securing the input gain plate.
3. Using a small slotted screwdriver turn the gains all the way down.
4. Turn your Source Unit volume to 90% output.
5. For best results adjust one input gain
at a time. Start with the fronts rst. We
reccommend testing a variety of music
genres to nd the best audible gain level
for your system.
6. Slowly turn up the input gains to your
amplier until you hear slight audible
distortion. Then back it down until the
distortion is gone.
7. Repeat step 6 to set the rear input gains.
SSV Works WP Series ampliers are designed with weather-proof durability and Plug-and-Play
harnessing. The WP-A360s4 amplier is pre-tuned for SSV Works Source Units, which provides the best
output levels with no distortion.
Front Speaker
Outputs Colors
Left Front (+) White
Left Front (-) White/Black
Right Front (+) Gray
Right Front (-) Gray/Black
Wire Color Polarity Location
Red + 12v Connect to Battery
Black - Ground Chassis Ground
Rear Speaker
Outputs Colors
Left Front (+) Green
Left Front (-) Green/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Source Units Plug-and-Play
Compatible
BMC Requires Part# HRCAF
MRB2 Yes
MRB3 Yes
Source Units Plug-and-Play
Compatible
USB35AVC Requires Part# HRCAF
Aftermarket Radio Requires Part# HRCAF
WP-A360S4 WP-A360S4
BATTERY
+
-
FRONT SPEAKERS
Low Level
Inputs
Speaker
Outputs
Power
Inputs
REAR SPEAKERS
AUDIO
SOURCE
UNIT
MOUNTING:
• When using a SSV Works amp wiring kit,
mounting hardware is included.
• If mounting in a custom location,
please use appropriate hardware for
all weather condidtions and mounting
surfaces.