StagePro CROMA 10R User manual
MANUAL DE USUARIO
CROMA 10R
alienpro.com.mx
alienpromx1 Alien Pro @alienpro_mx Alienpro_mx Alienpro_mx
In order to guarantee the product’s life, please don’t put it in the damp places or even the
environment over 60degress.
Always mount this unit in safe and stable matter.
Install or dismantle should operate by professional engineer.
Using lamp, the change rate of power voltage should be within±10%, If the voltage is too
high, it will shorten the light’s life; If it’s not enough, will influence the effect.
Please restart it 20 minutes later after turning off light, until full-cooling. Frequent
switching will reduce the life span of lamps and bulbs; intermittent using will improve the
life of bulls and lamps.
In order to make sure the product is used well, please read the Manual carefully.
1
www.ali e n p r o . c o m . m x
12
www.alienpro.com.mx
To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
Intermittently using will extend this item’s service life.
Please clear the fan , fan net , and optical lens in order to keep good work state.
Do not use the alcohol or any other organic solvent to wipe the shell.
1.1 Maintenance
The product has perfect performance and integrity packing. All users should be strictly complying
with the warning and operating instructions as stated. Or we aren’t in charge of any result by
misusing. Any damage resulting by misuse is not within the Company’s warranty. Any fault or
problem caused by neglecting the manual is also not in the charge of dealers.
Note: All information is subject to change without prior notice.
1.2 Statement
10 Gobo 231-235 Gogo14 shake slow-fast speed
236-240 Gogo15 shake slow-fast speed
241-245 Gogo16 shake slow-fast speed
246-250 Gogo17 shake slow-fast speed
251-255 Gogo18 shake slow-fast speed
11 Prism 1 0-63 Prism excluded
64-127 Prism 1 inserted
128-191 Prism 2 inserted
192-255 Prism 3 inserted
12 Prism 0-127 Position 0-360°
1 rotation 128-187 Fast to slow rotation
188-195 Stop
196-255 Slow to fast rotation
13 Prism 2 0-127 Prism excluded
128-191 Prism 4 inserted
192-255 Prism 5 inserted
14 Prism 2 0-127 Position 0-360°
rotation 128-187 Fast to slow rotation
188-195 Stop
196-255 Slow to fast rotation
15 Focus 0-255 From far to close
16 Rainbow 0-127 Rainbow wheel excluded
wheel 128-255 Rainbow wheel inserted
17 Lamp 0-025 Unused range
control 026-100 Lamp off
101-255 Lamp on
18 Reset 0-239 Unused range
240-255 Reset in 3s
1.3 Safety Precaution
Chapter 1 Installation and Attention
Power Input: 127Vca 60Hz
Power Dissipation
Power Consumption: 280W
: 400W
lamp:10R Bulb (life:2200 hours Color temperature: 8000K)
Channel mode:18CH DMX512 Channel
Control mode: DMX, auto-run, master/slave and sound-activate
Pan scan: 540°(16bit) Electric correction
Tilt scan:270° (16bit) Electric correction
Color wheel: 14 colors+white
1.4 Product Instruction
11
www.alienpro.com.mx
2
www.alienpro.com.mx
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm
characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable
with characteristics differing from those specified. The end connections must be made using XLR
type 3 male/female connectors. A terminating plug must be inserted into the last projector with
a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the
connectors. The casing itself must be connected to the shield braid and to pin 1 of the
connectors.
1.5 Cable Connection（DMX）
Figure 1 DMX Cable connection
- Gobo 20-24 Gobo4
25-29 Gobo5
30-34 Gobo6
35-39 Gobo7
40-44 Gobo8
45-49 Gobo9
50-54 Gobo10
55-59 Gobo11
60-64 Gobo12
65-69 Gobo13
70-74 Gobo14
75-79 Gobo15
80-84 Gobo16
85-89 Gobo17
90-94 Gobo18
95-125 Forward running from fast to slow
126-130 Stop
131-165 Backward running from fast to slow
166-170 Gogo1 shake slow-fast speed
171-175 Gogo2 shake slow-fast speed
176-180 Gogo3 shake slow-fast speed
181-185 Gogo4 shake slow-fast speed
186-190 Gogo5 shake slow-fast speed
191-195 Gogo6 shake slow-fast speed
196-200 Gogo7 shake slow-fast speed
210-205 Gogo8 shake slow-fast speed
206-210 Gogo9 shake slow-fast speed
211-215 Gogo10 shake slow-fast speed
216-220 Gogo11 shake slow-fast speed
221-225 Gogo12 shake slow-fast speed
226-230 Gogo13 shake slow-fast speed
Fixed gobo: 18 gobos+white
Prism wheel 1: 16-facet prism, 6-facet mirror, 8+24 facet prism
Prism wheel 2: 8-facet prism, 6-facet prism, frost
Rainbow effect
0-100% mechanical dimming, mechanical dimming and free dimming available.
Strobe macro control available.
Beam angle: 3.8-45°
Over heat protection
IP level: IP20
Net weight: 15.7KG
DMX512 2
SIGNAL.-
DMX512
3PIN
SCREEN
SIGNAL.+
1
3
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking
system makes it easy to fasten to the bracket.
Attention! Two clamps are needed to fix the equipment. Every clamp is locked by fastener of 1/4
kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary
accessory can not hang on the delivery handle. Nip the equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or not? If stand ten times
weight as the equipment. Make sure the architecture can stand ten times weight as all the
equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to
clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock
the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of
the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment
to flammable material or lighting source.
Figure 2 Panel diagram
1.6 Rigging (Optional)
9 Color 15-19 Color1+Color2
20-24 Color2
25-29 Color2+Color3
30-34 Color3
35-39 Color3+Color4
40-44 Color4
45-49 Color4+Color5
50-54 Color5
55-59 Color5+Color6
60-64 Color6
65-69 Color6+Color7
70-74 Color7
75-79 Color7+Color8
80-84 Color8
85-89 Color8+Color9
90-94 Color9
95-99 Color9+Color10
100-104 Color10
105-109 Color10+Color11
110-114 Color11
115-119 Color11+Color12
120-124 Color12
125-129 Color12+Color13
130-134 Color13
135-139 Color13+ White
140-199 Forward running from fast to slow
200-255 Backward running from fast to slow
10 Gobo 0-4 White
5-9 Gobo1
10-14 Gobo2
15-19 Gobo3
2.1 Brief
The light panel diagram show as Figure 2, Left area is TFT Displayer, support touch, and right
area is KEY, both of touch and KEY can operate light and setting.
Display & operation just like ‘Android operation system, touch the item will set or modify setting.
Note: Prevent damage the touch or TFT displayer, Can not use sharp objects chick displayer.
Chapter 2 Panel Operation
3
www.alienpro.com.mx
10
www.alienpro.com.mx
Figure 3 Dialog of value setting
Channel Function DMX Value Feature
1 Pan 000-255 0-540°
2 Pan fine 000-255 0-2°
3 Tilt 000-255 0-270° 0-1°
4 Tilt fine 000-255 0-1°
5 P/T speed 000-255 From fast to slow
6 Frost 0-127 No effect
128-255 Frost inserted
7 Strobe 0-3 Closed
4-103 Pulse strobe from slow to fast
104-107 Open
108-207 Gradual strobe from slow to fast
208-212 Open
213-251 Random strobe from slow strobe
252-255 Open
8 Dimmer 000-255 0-100% dimmer
9 Color 0-4 White
5-9 White+Color1
10-14 Color1
2.2.1 Operate Light with Touch or KEY
The left area is TFT Displayer and touch, chick item or value with finger will to complete
operation of set light setting (parameters) or view light state.
The area on the right hand side is 4 KEY, As auxiliary input interface, if disable touch
function,, the KEY can be choose to set the parameter..
2.2 Operation
2.2.2 Parameter Value Setting
2.2.3 Boolean Parameter Setting
Modify value: Can quickly modify value via pull the slider to the desired position, or click
the button of ‘up’ or ‘down’ whit finger on the right side to set the exact desired value,
another way is roll encoder on the right hand side of panel.
Apply value:When Value had been modified, Then press the bottom of ‘apply’ in the left
corner to apply to the light, but haven’t saved;
Save Value:Any time, click on the lower right corner of the "OK" button, the setting will
been saved into internal memory.
2.3.6 STAT-->Status: View Status
Enter the page as shown in Figure 11.
Work Mode: Show the current working mode.
Address: Show the current address.
Version: Show the version of the lamp.
Elapse: Working hours after turn on.
Tatol: Cumulative hours of operation
when the selected parameters is a Boolean value (such as ON or OFF), can directly modify
setting by chick corresponding item, the setting will been saved right now.
When the parameter is a key item, chick corresponding item, a dialog shown in Figure 4
will been popup ask for the confirm. Chick ‘sure’ to confirm.
9
www.alienpro.com.mx
4
www.alienpro.com.mx
When the selected item is value need to been modified, the dialog shown in Figure 3 will popup
Chick item of main menu, enter corresponding sub menu, shown in Figure 5, total 6 sub menu,
includes class of parameter and status:
ADDRESS: Set light DMX address.
WORKMOD: Set light work mode, master or slave mode when in auto run mode.
DISPLAY: Set display parameter, eg. select language.
TEST: Used for test light, modify DMX channel data to test functionthe corresponding
function of reference channel function table.
ADVANCE: Set light running parameter.
STATUS: View light current status.
Figure 10 page of run parameter Figure 11 page of status
Figure 4 Dialog of confirm
Figure 5 Parameter menu
2.3 Operation and Parameter Instruction
2.2.4 Sub Menu (Parameter)
2.3.4 TEST--> Test Mode
Enter the page as shown in Figure 9, light will into test mode, in this mode, the light does not
receive the data for DMX controller:
PAN: range for 0 to 255; GOBO: range for 0 to 255;
TILT: range for 0 to 255; PRISM: range for 0 to 255;
FOCUS: range for 0 to 255; FROST: range for 0 to 255;
COLOR: range for 0 to 255; STROBE: range for 0 to 255;
2.3.5 ADVA-->Advanced: Set Light Run Parameter
Enter the page as shown in Figure 9, set the parameter of light
Pan Invert: Reverse PAN move
OFF--> Pan Normal move. (Default)
ON--> Reverse PAN move.
Tilt Invert: Reverse TILT move
OFF--> Tilt Normal move. (Default)
ON--> Reverse Tilt move.
P/T Rectify: Disable or enable position rectify function.
OFF--> Disable P/T rectify
ON--> Enable P/T rectify-(Default)
Pan Offset: Set PAN original position. Default: 10
Tilt Offset: Set TILT original position. Default: 10
Lamp when: PowerON--> Turn on the lamp when power on. (Default)
RstDone--> Turn on the lamp after reset.
Manual--> Manually turn on the lamp.
Data hold:
OFF--> When no DMX signal, return to middle position. (Default)
ON--> When no DMX signal, stop in the final position.
Factory Setting: Restore all parameter to factory setting.
Via following operation, enter sub menu (parameter menu) shown in Figure5
In main menu, chick 1/6 function button into corresponding parameter menu.
In sub menu(page), chick main item on the left side of displayer, can shift to corresponding
sub menu(page) quickly.
5
www.alienpro.com.mx
8
www.alienpro.com.mx
Figure 8 page of display Figure 9 page of Test
Figure 6 page of DMX Address Figure 7 page of work mode
2.3.1 ADDR--> Address: Set DMX Address 2.3.3 DISP-->DISPLAY: Set Display
Click and select the "ADDR", can enter the page of DMX address setting, range from 1 to 512, the
address code shouldn’t is not greater than (512- channels quantity), otherwise the light will not
been controlled. Following is the operation:
Enter the page of DMX address, as shown in Figure 6, click the blank area in right side of display will
pop-up dialog as in Fig. 3, modify value, then click ‘ENTER’ to confirm and save DMX address code.
2.3.2 MODE--> Work Mode: Set Light Work Mode
Enter the page of ‘Work Mode’ as shown in Figure 7 and modify setting. Can set light work mode,
control lamp and DMX channel mode.
DMX Ctrl: Choose to set DMX Mode,
Auto Run: Choose to set Auto Mode,
Sound Ctrl: Choose to set Sound Mode,
M/S Choose: Available just in ‘AUTO RUN’ or ‘SOUND Ctrl’ mode.
ON--> Master. (Data will be sent to other slave lamp immediately.)
OFF--> Slaver. (NOT send data to other lamp via DMX Cable). (Default)
Light Switch:
ON--> Turn on the light,
OFF--> Turn off the light.
Channel Qty: Light support 2 DMX Channel mode: sample or extend.
Simple --> 16CH. (Default)
Expand--> 20CH (or null).
Light support 2 language, rotation display, Enter page as shown in Figure8 to set parameter
following:
Language: English / 中文.
Screen Saver: When panel is idle(these is no operation in 10 seconds), displayer will enter
saver status.
OFF--> No screen saver.
Mode1--> Power-saving mode, turn off the display.
Mode2--> Displays the current address.
Mode3--> Displays the icon and the current working mode.(Default)
Screen Rotation: To turning display.
ON--> Normal display. (Default)
OFF--> 180° turning display.
Touch enable: Disable or enable touch function,.
ON--> Enable touch function.(Default)
OFF--> Disable touch function.
Touch adjust:Adjust touch function. Normally, not enter this item.
7
www.alienpro.com.mx
6
www.alienpro.com.mx
Table of contents
