Stagg headbanger10 User manual

!
User Manual
HEADBANGER10
SLI MHW HB10

!
Maintenance
1. Avoid contact with high humidity or direct contact with moisture.
2. Using the product for extended run cycles without pause can shorten lifespan
3. Cleaning the lens and fan assemblies and blowing out dust from the product is
mandatory maintenance and will extend lifespan.
4. Never use petroleum-based cleaning agents or solvenst on the product, this
will damage the product permanently
Statement
All products are checked carefully before packing and shipping. Should you find
the product to be damaged when opening the box, contact your dealer. Any
misuse of the product due to neglect of the guidelines in this manual will void
your warranty. The dealer or manufacturer can never be held responsible should
this occur.
Technical details can be changed without notice
Attention
1. Never use the product in high humidity, in direct or indirect contact with
moisture or in locations with high temperatures. Failure to do so will void your
warranty.
2. Always place the product on a solid and even surface. When installed with the
hanging bracket, always make sure to use an approved mounting clamp and
check the mounting points for wear or damage.
3. A trained professional should perform all repairs and maintenance. Never open
the product without approval from your dealer.
4. Always use a stable power source within operating specifications.
5. Allow the light to cool down for 20 minutes before re-using.

!
Product Introduction
•Power Supply AC90-230V, 50Hz-60Hz
•Power consumption: 80W
•7pcs*10W RGBW LED
•DMX-Control-channels: 7 or 12, user selectable
•Color: RGBW Color-mixing
•Strobe: Flash rate: 0-10Hz
•Dimmer: 0-100%
•Maximum PAN-movement: 540o
•Maximum TILT-movement: 270o
•Master/Slave function
DMX Channel Summary –7 Channels Mode
CHANNEL
VALUE
FUNCTION
1
0
Stop
1~255
Adjust Pan
2
0
Stop
1~255
Adjust Tilt
3
0~10
Close
11~255
Dimmer
4
0
Close
1~255
Red
5
0
Close
1~255
Green
6
0
Close
1~255
Blue
7
0
Close
1~255
White

!
DMX Channel Summary –12 Channels Mode
CHANNEL
VALUE
FUNCTION
1
0
Stop
1~255
Adjust Pan
2
0
Stop
1~255
Adjust Pan fine
3
0
Stop
1~255
Adjust Tilt
4
0
Stop
1~255
Adjust Tilt fine
5
0~10
Close
11~255
Dimmer
6
0
Close
1~255
Red
7
0
Close
1~255
Green
8
0
Close
1~255
Blue
9
0
Close
1~255
White
10
0~9
Close
10~255
Color Macros
11
0~9
No strobe
10~255
Adjust strobe from slow to fast
12
0~127
Stop sound active mode
128~255
Activate sound active mode

!
Display Control Instruction
ADDR
DMX Adress
A001-A512
CHND
Channel Mode
7CH/12CH
SLND
Master/Slave
NAST/SL1/SL2
SOUN
Sound Sensitivity
0-100
AUTO
Auto Mode
NO/YES
STBY
Standby
NO/YES
PAN
PAN Reverse
NO/YES
TILT
TILT Reverse
NO/YES
LED
LED On/Off
ON/OFF
DISP
Display On/Off
ON/OFF
TEST
Self Test
HOUR
Show Total Runtime
RSET

!

!

!
!
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS.
• If, after you have followed the instructions outlined above, this device fails to function, please
contact your dealer. Under no circumstances should this device be opened. Leave all servicing to
qualified personnel.
•Electrical appliances must never be used in conditions of high humidity or heat. To prevent any risk
of fire or electric shock, never spill or splash liquids on this device. Should this happen, unplug the
power cable from the mains outlet and switch off the mixer immediately.
MARKING & CONFORMITY
1. The CE mark on this product means it conforms to the EMC Directive (2004/108/CE), CE marking
Directive (93/68/EEC) and Low Voltage Directive (2006/95/EC).
2. The «Crossed-out Wheeled Bin» is to draw your attention to the WEEE (Waste Electric &
Electronic Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately
for recycling.
3. «RoHS compliant» means this device conforms to the Directive (2002/95EC) on the restriction of
the use of certain hazardous substances in electrical and electronic equipments, such as: Mercury,
Lead, Cadmium, Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated
Diphenyl Ethers (PBDE).