Stagg PMS15D600 UBT User manual

• This active speaker system must be connected to a mains (AC) outlet to work properly and must be earthed
to operate safely.
• Ensure that correct AC mains voltage and socket - tted with a real ground connection - are available
before powering up the unit.
• Check mains power cable and plugs before switching on the equipment. If the mains cable and/or plug are
damaged, replace the whole cable immediately. For your own and other people’s safety, never repair or
modify the mains power cable. Dispose of the defective cable properly for waste and recycling purpose.
• After following the instructions outlined above, if your powered speaker fails to function, please contact your
vendor. Under no circumstances should the cabinet be opened. Leave all servicing to qualied personnel.
• Electrical appliances must never be used in conditions of high humidity or heat. To prevent any risk of re
or electric shock, never spill or splash liquids on the amplier. Should this happen, unplug the power cable
from the mains outlet and switch off the powered speaker immediately.
• May we draw your attention to the instructions printed on the rear panel of the cabinet.
• Make sure that the cabinet is placed or installed in such way that it can never injure people
• Do not place objects which are sources of heat on the speaker cabinet such as lighting equipment
or smoke machines.
IMPORTANT SAFETY INSTRUCTIONS
READ AND KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS.
WARNING
Exposure to extremely high noise levels may cause permanent hearing damage. Please use this amplied
speaker responsibly for you and your neighbourhood..
CLEANING
Do not attempt to clean the plastic enclosure with solvents or petrochemical based cleaners.
MARKING & CONFORMITY
• The CE mark on this product means it conforms to the EMC Directive (2004/108/CE), CE marking Directive
(93/68/EEC) and Low Voltage Directive (2006/95/EC).
• The “Crossed-out Wheelie Bin” is to draw your attention to the WEEE (Waste Electric & Electronic
Equipment) Directive (2002/96/EC). It means this apparatus must be collected separately for recycling.
• “RoHS compliant” means this device conforms to the (2002/95EC) Directive on the restriction of the use of
certain hazardous substances in electrical and electronic equipment, such as: Mercury, Lead, Cadmium,
Hexavalent Chromium, Polybrominated Buphenyl (PBB) and Polybrominated Diphenyl Ethers (PBDE).
MENU MP3 Player
Repeat
MODE USB /SD/Bluetooth SWITCH
EQ Equalizer
FOLDER - Last Folder
FOLDER+ Next Folder
TRACK Last Music Song
TRACK Next Music Song
Stop/Play
FUNCTIONS
1. MP3 player / Bluetooth Controls.
By pushing the mode button you can choose to use the USB/SD card player, the Bluetooth media
transfer or neither. In Bluetooth mode the display will show unconnect till you make a connection
from your smartphone. To do so go into your settings, go into Bluetooth, look into the list of
unknown Bluetooth units for the speaker, connect and allow your music player in your smartphone
to connect with Bluetooth. Once connected the display on the speaker will show connected , open
the MP3 and master volume to hear the result.
2. LEVEL: Volume of USB /SD player & Bluetooth
3. LEVEL: Volume of Microphone input
2
3
4
5
6
7
15
14
1
8
9
10
11
12
13
17
18
16

User’s manual
MULTI PURPOSE AMPLIFIED
SPEAKER CABINETS
2-WAY, DIGITALLY BI-POWERED SPEAKERS
PMS15D600 UBT, PMS12D400 UBT
EMD Music - 04/2015
Features and Specifi cations are subject to change without notice.
4. LEVEL: Volume of Auxillary input
5. VOLUME: Master Volume
6. TREBLE: Controls the amount of high frequencies in the output signal
7. BASS: Controls the amount of low frequencies in the output signal
8. MIC INPUT: XLR connector to connect microphone (low impedance balanced)
9. MIC INPUT: ¼” phone jack connector to connect microphone or high impedance sources such
as guitars or keyboards.
10. LINE INPUT: RCA left & right channels input. Allows you to connect an external audio device
such as CD player or Recording device.
11. LINE INPUT: XLR connector to control Line input. Allows you to connect an balanced external
audio device at line level such as CD player or Recording device.
Wiring of the 3-pin connector is: Pin 1= Shield; Pin 2 = Positive (Hot); Pin 3 = Negative (Cold).
12. LINE OUT : ¼” phone jack connector to connect an other ampli er or another powered
speaker cabinet in series.
13. LINE OUT: XLR connector to connect an ampli er or another powered speaker cabinet in series.
14. CLIP LED: LED warning indicator. This LED comes on when the input signal reaches distortion.
Reduce the input level in order to reduce the distortion.
15. POWER INDICATOR: LED indicator light for when unit is receiving mains power.
16. POWER SWITCH : This switch turns the power on and off.
17. VOLTAGE SELECTOR: The AC input voltage switches from 110V-250V / 50-60Hz
18. AC CONNECTOR: IEC main inlet with build in fuse.
Model PMS15D600UBT PMS12D400UBT
Description 15″2way plastic active
speaker
12″ 2way plastic active
speaker
Amplifi er system Bi amp, class D Bi amp, class D
cross over active active
Max rated Power 255+45W RMS 165+35W RMS
510+90W peak 330+70W peak
Max SPL 115dB 110dB
Specifi cations Woofer 15" 60oz 3"VC 12" 50oz 2.5"VC
Tweeter 1.75"Ti.Diap.Driver 8Ω 1.35"Ti.Diap.Driver 8Ω
Freq Resp 30Hz-20KHz 30Hz-20KHz
Sensitivity 97dB±2dB 96dB±2dB
Impedance 4Ω 4Ω
Features bluetooth bluetooth
U S B / S D
(Folder MP3 Player)
U S B / S D
(Folder MP3 Player)
remote control remote control
Pole insert diameter 35mm 35mm
Cabinet dim (WxDxH) 41x34,5x68,5cm 37x30x59cm
Cabinet weight 13,6kg 11,76kg
Total weight
(incl pack)
20kgs 16kgs
Package (WxDxH) 48,5×40×74cm 42×34,1×62,8mm
Voltage SWITCH 110-250V/ 50-60Hz 110-250V/50-60Hz