Stanley Furniture 584-x3-50 BTG Installation guide

Model Number:
584-x3-50 BTG CRIB
536-x3-50 BTG CRIB
537-x3-50 BTG CRIB
560-x3-50 BTG CRIB
Your little one will sleep securely in this Stanley Furniture Crib. Proper assembly
will ensure every effort has been made to design this crib with your baby's safety in
mind. It is certified to meet all safety guidelines established byASTM International
and the CPSC-Consumer Product Safety Commission.
Thank you for purchasing a Stanley Furniture Crib. If you find that you are missing
a part or if a part is defective in any way, contact your Stanley Furniture retailer for
assistance.
Built to Grow Crib Assembly Instructions
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY

2
!WARNING: FAILURE TO FOLLOW THESE WARNINGS AND THE
 FALL HAZARD: When child is able to pull to a standing posion, set the maress to the
lowest posion and remove bumper pads, large toys and other objects that could serve
as steps for climbing out.
 When a child is able to climb out or reaches the height of 35 in. (90 cm), the crib shall no
longer be used.
 To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by your physician.
 STRANGULATION HAZARD: Strings can cause strangulaƟon! Do not place items with a
string around a childs neck, such as hood strings or pacifier cords. Do not suspend
strings over a crib or aach strings to toys.
 DO NOT place a crib near a window where cords from blinds or drapes may stran-
gle a child.
 To help prevent strangulaon ghten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
 Before each usage or assembly, inspect crib for damaged hardware, loose joints, loose
bolts or other fasteners, missing parts or sharp edges before and aer assembly and fre-
quently during use. DO NOT use crib if any parts are missing , damaged or broken. Con-
tact your dealer or write to Stanley Furniture, 200 North Hamilton St, No. 200, High
Point, NC 27260 for replacement parts and instruconal literature if needed.
 DO NOT substute parts. Use only bolts or parts supplied by manufacturer or parts of
comparable quality and equal dimensions. Do not allow ends of bolts or sharp edges to
be exposed.
 Follow warnings on all products in a crib.
 If refinishing, use a non-toxic finish specified for children's products.
 Infants can suffocate on sobedding. Never add a pillow, comforter or padding.
Never place addional padding under an infant.
 Infants can suffocate in gaps between crib sides and a maress that is too small.
 Never use plasc shipping bags or other plasc film as maress covers because they can
cause suffocaon.
 Do not allow child to crawl or play underneath crib.
 Use cauon when a vaporizer is in use. Always aim the vapor steam away from the crib
as well as away from any other wood furniture item.
 The crib must be fully assembled prior to use.
 Read all instrucons before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
 CAUTION: Any maress used in this crib must be at least 27-1/4” by 51-
5/8” with a thickness of no less than 4 inches and not exceeding 6 inches.
When Converng to a Toddler Bed:
 NEVER use bed with children under 15 months of age.
 The maximum weight of the intended user shall not be greater than
50 lb (22.7kg).

3
The crib illustrations in these instructions are generic in nature. The crib you have purchased
may not look like the ones illustrated; however, they all assemble in the same manner.
Identifying the Parts
Left Crib End
Mattress Spring Platform
Right Crib End
Headboard Footboard

4
8 Connector Bolts
2” (1/4” x 20 thread)
Identifying the Hardware
Identify the hardware included using the illustrations below
2 Allen Wrenches
8 Connector Bolts
3/4” (1/4” x 20 thread)
2 Metal Locator Pins
4 Metal Brackets
with Studs
1 Wrench
4 Caps
8 Cap Nuts
8 Lock Washers

5
Crib Assembly
NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
Attached to the mattress platform is a sleeve to store the instruction booklet.
After assembly is complete, return this instruction booklet to the sleeve for future
reference.
This crib conforms to the ASTM International and the CPSC-Consumer Product Safety
Commission guidelines for product safety. Please adhere to the guidelines in this book-
let for assembly, use and maintenance.
Note the recommendations below:
 Power tools are not recommended for assembly.
 Give yourself plenty of room to work.
 Due to the size of this bed, it must be assembled in the space it will occupy.
 The assembly will take two people to complete.
 Layout all the hardware and make sure that the proper length bolts are used in the
designated areas.
 Do not substitute hardware. If an item is missing or damaged contact Stanley
Furniture Company immediately for replacement. Inspect all component parts and
hardware prior to beginning the assembly process.
 Make sure all fasteners are tight.
 Above all, take your time and read the instructions carefully.
Tools required forAssembly:
 Allen Wrenches (provided)
 Box End Wrench (provided)

6
Attaching the End Sections
Step 1:
 Using (4) 2”(1/4”x 20 thread)
connector bolts, insert the bolts
from the back of the crib head-
board and tighten with the provid-
ed wrench. See Fig 1a.
 Support the headboard and attach
one end section to the headboard
by aligning the connector bolt in
the headboard with the upper hole
in the end section. See Fig 1.
 Repeat for the remaining End
Section.
 Fig 2. is how your crib should
look.
Figure 1.
Figure 2.
Ends assembled to headboard.
Figure 1a.
Enlarged view.
Allen wrench
2” (1/4” x 20 thread) Connector bolt
Headboard
End Rail
End Rail

7
Attaching “L” Metal Bracket to Mattress Platform
Step 2:
 Attach metal “L” brackets to the
crib mattress platform as shown Fig
3.
 Using (8) cap nuts and (8) lock
washers, attach the “L” brackets
to each end of the mattress platform
and tighten with the provided
wrench. See Fig 3a.
 Repeat for the remaining end.
 Fig 4. is how your mattress platform
should look.
Figure 3.
Figure 4.
Assembled “L” metal brackets to
Figure 3a.
Enlarged view.
Metal Bracket
Cap Nut
Wrench
Lock
Washer

8
Attaching the Mattress Platform
Step 3:
 Attach the mattress platform in the desired
position. (Before inserting the bolts, make
sure the instruction holder and the warning
label are facing up and readable as shown in
Fig 5 and the mattress platform is level.
 Using (4) 3/4” (1/4”x 20 thread) connector
bolts to attach the mattress platform. Insert
each bolt through the “L” bracket and loose-
ly start the bolt into the threaded inserts lo-
cated in the crib ends and headboard posts.
See Fig 5a.
 Do not tighten the bolts at this time.
 When the child is able to pull to a standing
position, set the mattress platform to the
lowest position and remove large toys and
other objects that could serve as steps for
climbing out.
 Fig 6. is how your crib should look with
Warning labels facing the front of the crib.
Figure 5.
Figure 5a.
Enlarged view. Allen wrench
3/4” (1/4”x 20 thread) Connector bolt
Figure 6.
Spring Mattress assembled to end rails & headboard.
Headboard
Higher Position
Mattress Platform

9
Attaching the Footboard
Step 4:
 Insert the two metal locator
pins in the crib end posts at this
time.
 Attach the footboard by align-
ing the footboard with the met-
al locator pins. See Fig 7a.
 Using (4) 2”(1/4”x20 thread)
connector bolts, loosely attach
the footboard as indicated in
Fig 8.
 After the bolts have been at-
tached, use the wrench provid-
ed to tighten each of the bolts
to secure the footboard.
 Securely tighten each mattress
platform bracket bolt at this
time.
 Fig 9. is how your crib should
look.
Figure 7.
Attach the footboard.
Figure 8.
Allen wrench
2” (1/4”x 20 thread) Connector bolt
Metal Locator Pin
Figure 9.
Assembled Crib.
Figure 7a.
Attach the footboard using
metal locator pin.
Footboard
Footboard

10
Final Step in Crib Assembly
Step 5: (The final and most important) Checklist.
 Inspect the crib once again to assure that all bolts are tight and that no hardware is missing. (if you
have missing hardware, contact Stanley Furniture immediately for replacement and do not use the
crib until the new hardware arrives).
 Do not place the crib near a window where the child may have access to window coverings, cords or
draperies as these articles pose a strangulation hazard.
 Replace the instructions in the holder provided. KEEP THE INSTRUCTIONS WITH THE CRIB.
 Install the crib mattress.
 Follow all the warnings on the use of this crib and all products in the crib.
 CAUTION: Any mattress used in this crib must be at least 27-1/4” by 51-5/8”
with a thickness of no less than 4 inches and not exceeding 6 inches.

11
Cleaning:
Mix together a mild solution of gentle dishwashing liquid and water, apply to the crib sur-
face using a soft clean cloth lightly dampened in the solution. Rinse with clear water
again using a soft clean cloth, then dry all surfaces thoroughly with a dry cloth. NO
ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COURSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Storage:
A permanent storage pouch is attached to the mattress platform for the storage of the as-
sembly instructions. After completing the assembly process, you are advised to read and
be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USEAND
MAINTENANCE notices contained in these instructions. Do not place excess hardware
in the storage pouch as it could present a danger to a child if retrieved and could also
damage the mattress. When storing the crib, use CAUTION as temperature changes and
humidity could be harmful to the crib. It is recommended that the crib be stored in a
temperature controlled environment.
Periodic Maintenance:
1. Periodically check to make sure all bolts and connections are fastened securely.
2. If you are missing a part or need a replacement part, do not substitute parts. Ask your
dealer for replacement parts or contact Customer Service at [phone].
3. The crib allows for 3 mattress heights. Move to the low position when the child can
pull up to a standing position. When the child reaches a height of 35” or can climb out
of the crib you should place the child in a youth or regular bed.
4. Save these instructions in the event you disassemble the crib and need to reassemble it.
These instructions will also be useful in identifying replacement parts if needed at a
future date.

12
Lowering the Spring Mattress
Lower Position
Steps to lower the mattress:
 Loosen the (4) 2” (1/4”x20 thread) bolts attaching the footboard as shown Fig. 10a.
 Loosen the (4) 3/4” (1/4”x20 thread) bolts attaching the Mattress Platform.
 Remove the crib footboard at this time.
 Lower the crib mattress platform to the desired setting.
 Follow Steps 3 and 4 on Pages 8, and 9 to reassemble the crib.
 Figure 12 is how your Crib should look.
Figure 11.
Enlarged view of Lowering the Mattress.
3/4” (1/4”x20 thread) Connector bolt
Figure 10a
Enlarged view of Footboard removal.
Allen wrench
2” (1/4”x20 thread) Connector bolt
Footboard
Higher Position
Figure 10.
Removing footboard from the Crib.
Figure 12.
Assembled mattress platform in low position.
Allen Wrench
Mattress Platform

13
Toddler Bed Conversion Kit is available as an
option to convert the Built to Grow Crib to a tod-
dler bed. Contact your Stanley Furniture dealer
to purchase this item.
Accessories and Options
Full Size Bed Conversion With Metal Bed
Frame is available as an option using a metal
bed frame. Contact your Stanley Furniture deal-
er to purchase this item.
Full Size Bed Conversion With Footboard is
available as an option to convert the Built to
Grow Crib to a full size bed. Contact your Stan-
ley Furniture dealer to purchase this item.

14
Step 1: Disassemble the crib or toddler/day bed.
 Using the wrench provided remove the components in the following order:
 Loosen footboard bolts & mattress platform bolts.
 Remove the footboard
 Remove the mattress platform
 Remove the crib ends from the crib headboard
 Keep and store all the hardware for future assembly of the crib. Store the crib components in a safe
dry place to prevent damage.
Step 2: Attach the side rails and slat roll.
 The side rails can be installed in two positions. The lower position is recommended for transition
from the crib to a child’s first full size bed. The bed side rails can be moved to the upper position
after your child adapts to the transition. Under bed storage options can be used with the bed rails
positioned in the upper location. Contact your Stone & Leigh dealer for more information on availa-
ble options.
 Install the rails to the headboard and footboard as shown in figure 16.
 Insert (4) 3/4” bolts & (4) caps in the headboard to cover the crib assembly holes. Tighten with the
wrench provided. See Figure 15.
 Install the slat roll using the screws and instructions provided with the slat roll for proper installa-
tion.
Converting to a Full Size Bed
Headboard
Figure 15.
See Figure 15.
Cap
Allen Wrench
Connector Bolt
3/4” (1/4” x 20 thread)
1/4” Threaded Rod
Curve Washer
Nut
Wrench
Headboard
See Figure 16.

15
Stanley Furniture Company
200 North Hamilton St
No. 200
High Point, NC 27260
For parts, contact your Stanley Furniture dealer.
For additional consumer information call our Customer Service Department at:
1-[phone]Mon.-Fri., 8am-5pm Eastern Standard Time
091215