Stanley STDH8013C User manual

STDH8013C
English Page 04
Russian Page 10
Ukrainian Page 19

B
A
0000 00-00
ENGLISH (Original instructions)
2
4
9
7
8
5
2
6
13
1
10
4
3

(Original instructions) ENGLISH
3
12
C
DE
76

Intended use
Your STANLEY STDH8013C impact drill has been designed
for drilling in wood, metal and concrete. This tool is intended
for professional use.
Safety instructions
General Power tool Safety Warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoid-
able, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
ENGLISH (Original instructions)
4

(Original instructions) ENGLISH
5
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Additional Power Tool Safety Warnings
Warning! Additional safety warnings for drills and
impact drills
Drill Safety Warnings
• Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
• Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
• Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
• Before drilling into walls, floors or ceilings, check for the
location of wiring and pipes.
• Avoid touching the tip of a drill bit just after drilling, as it
may be hot.
• This tool is not intended for use by persons(including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
• The intended use is described in this instruction manual.
The use of any accessory or attachment or performance of
any operation with this tool other than those recommended
in this instruction manual may present a risk of personal
injury and/or damage to property.
Safety of others
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
• Children should be supervised to ensure that they do not
play with the appliance
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. Even with the
application of the relevant safety regulations and the
implementation of safety devices, certain residual risks can
not be avoided. These include:
• Injuries caused by touching any rotating/moving parts.
• Injuries caused when changing any parts, blades or
accessories.
• Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Labels on tool
The label on your tool may include the following symbols:
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2017 XX JN
Year of manufacturing
Electrical safety
Double insulation measures are taken in this power
tool, so no grounding is needed. Please check
whether the voltage of power supplied is consistent
with the voltage on the nameplate or not.
• If the wire is damaged, it should be replaced by the
manufacturer or a service center authorized by STANLEY,
to avoid danger.
Using an extension cable
• If an extension cable is requred, use an approved
extension cable suitable for the power input of this tool
(see technical data). The minimum conductor size is
1.5 mm2.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute

ENGLISH (Original instructions)
6
• Check for damage to the tool, parts or accessories which
may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
Description (fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Mode selector
5. Ventilation slots
6. Side handle
7. Depth adjustment rod
8. Keyless chuck
9. Sleeve
10. Speed dail
Assembly
Warning! Before assembly, please ensure that the power tool
is powered off and the power plug of the tool is unplugged
from the power source.
Selecting the operating mode (fig. B) The tool can be used in
two operating modes:
Rotary drilling:
for steel, wood and plastics.
Impact drilling:
simultaneous rotating and impacting for concrete and
masonry drilling operations.
• Select the required operating mode by rotating the mode
selector (4) to the required position.
Inserting and removing a bit (fig. A,D)
Keyless chuck
The STDH8013C features a keyless chuck (8) for greater
convenience.
To Insert A Drill Bit Or Other Accessory.
• Grasp the rear half of the chuck with one hand and use
your other hand to rotate the front half counter clockwise,
as shown in Figure D. Rotate far enough so that the chuck
opens sufficiently to accept the desired accessory.
• Insert the bit or other accessory about 19 mm (3/4") into
the chuck and tighten securely by holding the rear half of
the chuck and rotating the front portion in the clockwise
direction. When the chuck is nearly tightened, you will hear
a clicking sound. After 4–6 clicks, the chuck is securely
tightened around the accessory.
• To release the accessory, repeat step 1 listed above.
Warning! Do not attempt to tighten drill bits (or any other
accessory) by gripping the front part of the chuck and turning
the tool on. Damage to the chuck and personal injury may
result.
Keyless Chuck Removal (Fig. D)
Tighten the chuck around the shorter end of a hex key (not
supplied). Using a soft hammer or piece of wood, strike the
longer end in the counterclockwise direction. This will loosen
the chuck so that it can be unscrewed by hand.
Keyless Chuck Installation (Fig. D)
Screw the chuck on by hand as far as it will go. Tighten the
chuck around the shorter end of a hex key (not supplied) and
strike the longer end in the clockwise direction with a soft
hammer.
Fitting the side handle (fig. A)
The side handle (6) can be fitted to suit both RH- and
LH-users.
Always use the drill with the side handle properly
assembled.
• Loosen the side handle.
• For RH-users, slide the side handle clamp overthe collar
behind the chuck, handle at the left.
• For LH-users, slide the side handle clamp colar behind the
chuck, handle at the right.
• Rotate the side handle to the desired positionand tighten
the handle.
Setting the drilling depth (fig. C)
• Insert the required drill bit into the chuck.
• Slacken the side handle (6).
• Fit the depth adjustment rod (7) through the hole in the
side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.
Forward/reverse slider (fig. A)
• To select forward or reverse rotation, use the
forward/reverse-switch (3) (see arrow on tool).
Always wait until the motor has come to a complete
standstill before changing the direction of rotation.
Instructions for use
• Always observe the safety instructions and applicable
regulations.
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool. Excessive force
does not speed up drilling but decreases tool performance
and may shorten tool life.
• Wear ear protectors with impact drills.Exposure to noise
can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.

(Original instructions) ENGLISH
7
• Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of
the power tool "live" and shock the operator.
• If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Prior to operation
• Insert the appropriate bit.
• Mark the spot where the hole is to be drilled.
Proper Hand Position (fig. A, E)
Warning: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
Warning: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(6), with the other hand on the main handle.
Switching on and off
• To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch.
• For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available
only at full speed.
• To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
• Based on the different applications, turn around the speed
dial (10) to control the maximum speed.
Drilling in metal
Start drilling with slow speed and increase to full power while
applying firm pressure on the tool. A smooth even flow of
metal chips indicates the proper drilling rate. Use a cutting
lubricant when drilling metals. The exceptions are cast iron
and brass which should be drilled dry.
Note: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in steel can
be made easier if a pilot hole [5/32" (4 mm) to 3/16" (5 mm)] is
drilled first.
Drilling in wood
Start drilling with slow speed and increase to full power while
applying firm pressure on the tool. Holes in wood can be
made with the same twist drills used for metal. These bits may
overheat unless pulled out frequently to clear chips from the
flutes. Work that is apt to splinter should be backed up with a
block of wood.
Drilling in masonry
When drilling in masonry, use carbide-tipped bits rated for
Impact drilling and be certain that the bits are sharp. Use a
constant and firm force on the tool to drill most effectively. A
smooth, even flow of dust indicates the proper drilling rate.
Screwdriving
• Select forward or reverse rotation.
Impact drilling (fig. A)
• Select the Impact mode.
• Press the switch (1).
Rotary drilling (fig. A)
• Select the rotary drilling mode.
• Proceed as described for Impact drilling.
Consult your dealer for further information on the appropriate
accessories.
Accessories
The performance of an electric tool depends on its
accessories. STANLEYaccessories are designed according to
high quality standards, to enhance the performance of electric
tool. The use of these accessories can help you conveniently
operate the tool.
Maintenance
The STANLEYcord / cordless appliance / tools are of
sophisticated design, can be used for a long time, and only
little maintenance is needed. To obtain consistent satisfactory
use, proper maintenance and regular cleaning of the tools are
necessary.
Warning! Before performing any maintenance work on the
cord / cordless electric tools, the following points must be
implemented:
• Switch off the power of the equipment / tools and pull off
the plug;
• If the equipment / tools are equipped with independent
battery pack, please turn off the power and remove the
battery pack from the equipment / tools.
• If the equipment / tools are equipped with an integrated
battery, please run out the battery, before turning off its
power.
• Before the cleaning, unplug the charger plug from the
power source. In addition, except the regular cleaning on
your charger, no other maintenance is needed.
• Regularly use the soft brush or dry cloth to clean the
ventilation slot of the equipment / tools / charger.
• Regularly use a damp cloth to clean the motor housing.
Please do not use any abrasive cleaning agents or
solvent-based cleansing agents.
• Regularly open the clamping chuck and tap it gently to
remove any internal dust (after installation).

ENGLISH (Original instructions)
8
Cleaning
Warning! Once the visible dust build-up is found at
and/or around the ventilating ports, immediately
flush the dust and powder within the host shell with
clean dry air. To perform this procedure, wear the
approved safety equipment and dust mask.
Warning! It is strictly forbidden to clean the
non-metallic parts of the tool with the solvents or
other irritant chemicals. These chemicals may
weaken the materials of these components. Use a
cloth moistened with a mild soapy water to clean it.
Do not let any substance permeate into the tool
and.do not immerse any part of the tool into a liquid.
Protecting the Environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
STANLEY provides a facility for the collection and
recycling of STANLEY products once they have
reached the end of their working life. To take
advantage of this service please return your product to any
authorised repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local STANLEY office at the address
indicated in this manual. Alternatively, a list of authorised
STANLEY repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Service Information
STANLEY offers a full network of company-owned and
authorized service locations throughout Asia. All STANLEY
Service Centers are staffed with trained personnel to provide
customers with efficient and reliable power tool
service.Whether you need technical advice, repair, or genuine
factory replacement parts, contact the STANLEY location
nearest to you.
Notes
• STANLEY’s policy is one of continuous improvement to
our products and, as such, we reserve the right tochange
product specifications without prior notice.
• Standard equipment and accessories may vary by country.
• Product specifications may differ by country.
• Complete product range may not be available in all
countries. Contact your local STANLEY dealers for range
availability.
Technical data
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of
exposure.
Warning: The declared vibration emission level
represents the main applications of the tool.
However if the tool is used for different applications,
with different accessories or poorly maintained, the
vibration emission may differ. This may significantly
increase the 1.5exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work
patterns.
Impact Drill STDH8013C
Voltage V 220-240
Frequency Hz 50/60
Power input W 800
No-load speed /min 0-3000
Impact rate IPM 0-54000
Reverse/Forward rotation Yes
Chuck capacity mm 1.5-13
Max capacity
Concrete mm 16
Metal mm 13
Wood mm 32
Weight kg 2.5
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 100.5 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 111.5 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN 60745:
Drilling into metal (ah, D) <6.1 m/s2, uncertainty (K) 1.5 m/s2
Impact drilling (ah, ID) 15.0 m/s2, uncertainty (K) 1.5 m/s2

(Original instructions) ENGLISH
9
EC declaration of conformity
MACHINERY DIRECTIVE
STDH8013C
STANLEY declares that these products described under
"technical data" are in compliance with: 2006/42/EC,
EN 60745-1:2009 + A11:2010, EN 60745-2-1:2010
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact STANLEY
at the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
STANLEY.
R.Laverick
Engineering Manager
STANLEY , Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
03.2017
Two Year Warranty
If your STANLEY product becomes defective due to faulty
materials or workmanship within 24 months from the date of
purchase, STANLEY guarantees to replace all defective parts
free of charge or – at our discretion – replace the unit free of
charge provided that:
• The product has not been misused and has been used in
accordance with the instruction manual;
• The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorized
persons;
• Proof of purchase is produced.
• The STANLEY product is returned complete with all original
components
• The product hasn’t been used for hire purposes
If you wish to make a claim, contact your seller or check the
location of your nearest authorised STANLEY repair agent in
the STANLEY catalogue or contact your local STANLEY office
at the address indicated in this manual. A list of authorised
STANLEY repair agents and full details of our after sales
service is available on the internet at: www.2helpU.com

IИспользование по назначению
Ваша ударная электрическая дрель STANLEY STDH8013C
предназначена для сверления отверстий в древесине,
металле, пластмассе и кирпичной кладке, а также для
заворачивания саморезов. Данный инструмент
предназначен для профессионального использования.
Инструкции по технике безопасности
Общие предупреждения по технике
безопасности электроинструментов
Внимание! Ознакомьтесь со всеми
правилами безопасности и инструкциями.
Несоблюдение предупреждений и инструкций,
указанных ниже, может привести к поражению
электрическим током, пожару и/или серьезной
травме.
Сохраните все предупреждения и инструкции для
будущего использования. Термин "электроинструмент"
во всех предупреждениях, указанных ниже, относится к
вашему сетевому (с кабелем) электроинструменту или
аккумуляторному электроинструменту (без кабеля
питания).
1. Безопасность рабочего места
a. Содержите рабочее место в чистоте и обеспечьте
хорошее освещение. Плохое освещение или
беспорядок на рабочем месте может привести к
несчастному случаю.
b. Не используйте электроинструменты, если есть
опасность возгорания или взрыва, например,
вблизи легко воспламеняющихся жидкостей,
газов или пыли. В процессе работы
электроинструменты создают искровые разряды,
которые могут воспламенить пыль или горючие пары.
c. Во время работы с электроинструментом не
подпускайте близко детей или посторонних лиц.
Отвлечение внимания может вызвать у Вас потерю
контроля над рабочим процессом.
2. Электробезопасность
a. Вилка кабеля электроинструмента должна
соответствовать штепсельной розетке. Ни в коем
случае не видоизменяйте вилку электрического
кабеля. Не используйте соединительные
штепсели-переходники, если в силовом кабеле
электроинструмента есть провод заземления.
Использование оригинальной вилки кабеля и
соответствующей ей штепсельной розетки уменьшает
риск поражения электрическим током.
b. Во время работы с электроинструментом
избегайте физического контакта с заземлёнными
объектами, такими как трубопроводы, радиаторы
отопления, электроплиты и холодильники. Риск
поражения электрическим током увеличивается, если
Ваше тело заземлено.
c. Не используйте электроинструмент под дождём
или во влажной среде. Попадание воды в
электроинструмент увеличивает риск поражения
электрическим током.
d. Бережно обращайтесь с электрическим кабелем.
Ни в коем случае не используйте кабель для
переноски электроинструмента или для
вытягивания его вилки из штепсельной розетки.
Не подвергайте электрический кабель
воздействию высоких температур и смазочных
веществ; держите его в стороне от острых кромок
и движущихся частей электроинструмента.
Повреждённый или запутанный кабель увеличивает
риск поражения электрическим током.
e. При работе с электроинструментом на открытом
воздухе используйте удлинительный кабель,
предназначенный для наружных работ.
Использование кабеля, пригодного для работы на
открытом воздухе, снижает риск поражения
электрическим током.
f. При нео бходимо с ти раб оты с
электроинструментом во влажной среде
используйте источник питания, оборудованный
устройством защитного отключения (УЗО).
Использование УЗО снижает риск поражения
электрическим током.
3. Личная безопасность
a. При работе с электроинструментами будьте
внимательны, следите за тем, что Вы делаете, и
руководствуйтесь здравым смыслом. Не
используйте электроинструмент, если Вы устали, а
также находясь под действием алкоголя или
понижающих реакцию лекарственных
препаратов и других средств. Малейшая
неосторожность при работе с электроинструментами
может привести к серьёзной травме.
b. При работе используйте средства
индивидуальной защиты. Всегда надевайте
защитные очки. Своевременное использование
защитного снаряжения, а именно: пылезащитной
маски, ботинок на нескользящей подошве, защитного
шлема или противошумовых наушников, значительно
снизит риск получения травмы.
c. Не допускайте непреднамеренного запуска.
Перед тем, как подключить электроинструмент к
сети и/или аккумулятору, поднять или перенести
его, убедитесь, что выключатель находится в
положении «выключено». Не переносите
электроинструмент с нажатым курковым
выключателем и не подключайте к сетевой розетке
электроинструмент, выключатель которого
установлен в положение «включено», это может
привести к несчастному случаю.
РУССКИЙ (Перевод с оригинала инструкции)
10