Starburst Technologies SB-3770ART-DR User manual

INSTALLATION GUIDE
Full motion recessed tv wall mount
SB-3770ART-DR
Support 37" to 70" Screens
Max Load Capacity: 200 lbs (91 kg)
VESA 500x800 compatible

2 of 7
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•¢6.0 drill bit and ¢10.0 masonry drill bits
WARNING
Table of Contents
Parts List ........................................................................................................................................................................ 3
Installation Wall Mount to In-Wall Box.... ............................................................................................................................... 4
Attaching adapter plate to Screen
............................................................................................................
............................................................................................................ ...........................
...
5、6
7
Mounting the
Tilt Adjustment and Cord Covers
•Be sure to read this entire manual thoroughly and you fully understand all the instructions and warning before
attempting to begin your installation.
•This product should only be installed by someone who has a basic knowledge of buiding construction,installations and fully
understands these instructions.
•Make sure that the supporting surface will safely support the combined load of the mount, the display and all
attached hardware and components.
•This wall bracket will only supporting flat panel displays(LCD,Plasma).The maximum load capacity is 200 pounds.
•If mounting to a wall of wood stud construction, be sure that mounting bolt are anchored to the center of the
studs.
•Always have someone assist you to lift and position your equipment.
•Tighten screws and bolts firmly, but do not over tighten. Over tightening can damage the items and greatly reduce
their ability to hold. Please refer to suggested torque values where applicable in these instructions.
•Socket Wrench

3 of 7
C
I J K
1 2
L
M
B
E F G HD
A
A
E
F
4
4
4
4
4
1
4
4
4
G
M6x12 / 6x13x1.2
M6x25
M8x12
M6x12
M5x25
M5x12
M8x25
M8x15/
25.65x25.65x2.5
17x9x14 / 13x7x13
M5
8.2x2.0x16
pan head screw
C4
washer 1
8.2x1.5x16
washer 2
D4
pan head screw
pan head screw
pan head screw
pan head screw
pan head screw
square spacer
allen wrench
B8
pan head screw / washer
H
I
J
spacer ( 1. 2. )
K
L
allen cap screw/
10
Mconcrete anchor ST6.3×50
with your product.
Parts may appear slightly different than illustrated.
Before you b egin, make sure all parts shown are included
Parts List
Description
Hooks
Adaptor
In-Wall Box Wall Mount

A
14.5”
21.5”
M1
M2
M3
M4
M5
N6
N7
N8
N9
N10
Determine where you want your tv mounted on
your wood stud wall. Note that the center of the
arm of this TV mount will represent the center of
your TV. Choose the appropriate height for your
viewing pleasure. The location you choose must
be between two 16 in on center wood studs .
A1: Now that you have chosen an area. Mark
out an area 14.5 inches wide and 21 inches tall.
Note again the center of this area will be the
center of your TV . Make sure that the vertical
edge lines are located on the inside edge of your
wood studs. Fig.1
A2 : Cut out the drywall in the marked area with the
appropriate tools . Fig.1
A3: Insert the metal in wall box into opening. While
pushing the box against the right stud, mark the location of
holes M1 and M2. Remove in wall metal box.
A4: Pre drill the two marked locations M1 and M2 with a 3/16
inch drill bit.
A5: Insert Metal in wall box into opening. Take two screws
(M) from Bits Bag. Using a wrench tighten screws M1 and
M2. Shown in Fig 2.
A6: Insert Wall mount into In wall metal box. Extend both top
and lower braces until they touch both studs. Hold and mark
location of all holes M3 through N10. Fig.3
A7: Remove wall mount from in wall box. Drill 3/16 inch
holes completely through stud in locations M3 to N10.
A8: Put wall mount back into recessed in wall box. Insert
and tighten all screws using 8 lag screws (M/N) from bits bag
in location M3 to N10. Fig 3
Caution: Do not tighten screws with impact drill or hammer.
Hand tighten to not cause damage to wood stud and or lag
screw.
4 of 7
A

5 of 7
Mounting the Assembly Adapter Plate to screen
Modify the Adapter Plate
Adaptor Modify the Assembled Adapter Plate
Slide the adapter brackets into Assembled adapter plate slightly.
Place the Assembled Adapter Plate on the back of the display with
one Adapter Bracket aligned with a set of vertical mounting
holes.Then,slide the other Adapter Bracket in or out until it aligns
with the second set of vertical mounting holes.The Adapter should
be horizontally centered on the back of the flat panel display.
Adaptor and hooks Use four M6x12 screws and four washers
and tighten it with Phillips Head Screw Driver.
Adapter
Bracket
Adaptor and hooks
Back of Screen
Adaptor and hooks
M6x12
Screw
washers
(￠13x￠6x1.2)
Top of
Display
*For screen with a hole
pattern in a pocket,spacers
go between Assembly
Adapter Plate and screen. Spacers
Mounting
Screw
M6&M8
Hole
M5 Hole
Square
spacer
Note:
Recessed Mounting Holes.
If the mounting holes are recessed
into the back of the display, use the
supplied spacers to pack the
recessed hole. If the mounting
screw is M5&M6,use the
Spacers1.(K.1.)If the mounting screw
is M8,use the Spacers 2.(K.2.)
Ensure that the brackets are
securely fixed to the display.
B

6 of 7
top screw
Attach Assembly Adapter Plate to Assembly Arm
.25"
Iron spacer
washers
M8x15mm
screw bolt
M8x15mm
screw
1. Insert two M8x15mm screws
and two metal washers into swivel box
on Assembly Adapter Plate as above
shown.
Leave approx. 1/4" of exposed thread.
NOTE:This procedure will require
two persons.Ensure that the arm is
set to its maximum negative tilt prior
to attaching the display
2. Lift the display and hook it
over the mounting head by lowering
the exposed portion of the top screws
down the open key slots.
3. Once in position, attach the bottom
two M8x15mm screws and two
washers to secure the display to the
mounting head using M5mm Allen
Wrench.
For Flat Back Screen
SCREEN
SPACER
SCREEN
fig C.1 fig C.2
SCREW
AA(mount)
OR
Select the small,medium,large or extra large screws from the baffled .Fastener pack then attach
screen brackets(AA) to screen following figure C.1 or C.2 on page 7.
SCREW
AA(mount)

7 of 7 REV:20141113-B
WARNING:
Before removing
your
display,ensure
the display has a
negative Tilt and
Tilt Lever is
LOCKED!
Tilt Adjustment
Loosen
Tighten
1.Loosen Tiltlevers(Only enough to
allow controlled adjustment)
2. Adjust Tilt
3. Lock Tilt Levers(Tighten)
4. Once Tilt Levers are locked,the position of the levers can be adjusted
without loosening ortightening the unit
by pulling the levers outwards and then
repositioning them to a vertical,less
obtrusive position.
Tiltlever
Install Cord Covers as shown.
NOTE:Be sure to leave enough
slack to allow for movement of
the arms.
Cord Covers
Cord Covers
CTilt Adjustment and cord Coves