StarTech.com ARMSLIMDUOS User manual

Manual Revision: 12/18/2019
User Manual
For the latest information and specications visit
www.startech.com/ARMSLIMDUOS
Dual Monitor Mount with Built-in 2-port USB
Pass-Through | Silver
SKU#: ARMSLIMDUOS
Actual product may vary from photos

1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and
other protected names and/or symbols of third-party companies not related in
any way to StarTech.com. Where they occur these references are for illustrative
purposes only and do not represent an endorsement of a product or service
by StarTech.com, or an endorsement of the product(s) to which this manual
applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com
hereby acknowledges that all trademarks, registered trademarks, service marks,
and other protected names and/or symbols contained in this manual and
related documents are the property of their respective holders.

2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Warning Statements
• Makesurethatyouassemblethisproductaccordingtotheinstructions.
• Donotexceedtheweightcapacityofthisproduct.Overloadingthis
productmightresultininjuryorpropertydamage.Thisproductcan
supportthefollowingweight:17.6lb.(2x8kg).
• Thisproductisintendedforindooruseonlyandshouldnotbeused
outdoors.
Varningsmeddelanden
• Setillattdumonterarproduktenienlighetmedinstruktionerna.
• Överskridinteproduktensviktkapacitet.Överbelastningavprodukten
kanorsakaskadapåpersonelleregendom.Dennaproduktharstödför
följandevikter:(2x8kg).
• Produktenärendastavseddföranvändninginomhusochskainte
användasutomhus.
Avertissements
• Assemblezceproduitconformémentauxinstructions.
• Nedépassezpaslacapacitépondéraleduproduit.Unesurchargedu
produitpeutentraînerdesblessuresoudesdommagesmatériels.Ce
produitpeutsupporter(2x8kg).
• Ceproduitestuniquementdestinéàuneutilisationenintérieuretne
doitpasêtreutiliséàl’extérieur.
Warnhinweise
• BeachtenSiebeiderMontagediesesProduktsdie
Montageanweisungen.
• ÜberschreitenSienichtdieTragkraftdiesesProdukts.EinÜberladen
diesesProduktskannzuVerletzungenoderzurBeschädigungdes
Produktsführen.DiesesProduktistfürfolgendesGewichtgeeignet:(2
x8kg).
• DiesesProduktistnurzumGebrauchinInnenräumenvorgesehenund
solltenichtimFreienverwendetwerden.
Dichiarazioni di avvertenza
• AssicurarsidiAssemblareilprodottosecondoleistruzioni.
• Nonsuperarelacapacitàdicaricodelprodotto.Ilsovraccaricodel
prodottopotrebbecausaredanniolesioni.Ilprodottoèingradodi
supportareiseguentipesi:(2x8kg).

3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
• Ilprodottoèdestinatoall’usoinambientiinterni.Senesconsiglia
l’impiegoinambientiesterni.
Mensagens de aviso
• Certique-sedequemontaesteprodutodeacordocomasinstruções.
• Nãoexcedaacapacidadedepesodesteproduto.Sobrecarregareste
produtopoderesultaremferimentosoudanosdepropriedade.Este
produtopodesuportaroseguintepeso:(2x8kg).
• Esteprodutodestina-seapenasaumautilizaçãonointeriorenãodeve
serutilizadonoexterior.
Advertencias de uso
• Asegúresedeensamblaresteproductosegúnlasinstrucciones.
• Asegúresedenoexcederlacapacidaddepesodeesteproducto.La
sobrecargadeesteproductopuedecausarlesionespersonalesodaños
enlapropiedad.Esteproductotienecapicidadparaelsiguientepeso:
(2x8kg).
• Elusodeesteproductoessoloparainterioresynodebeutilizarseen
exteriores.
Waarschuwingen
• Zorgdatuditproductvolgensdeinstructiesinelkaarzet.
• Overschrijddemaximalecapaciteitvanditproductniet.Overbelasting
vanditproductkanletselofmateriëleschadeveroorzaken.Ditproduct
ondersteunthetvolgendegewicht:(2x8kg).
• Ditproductisalleenbedoeldvoorbinnengebruikenmagnietbuiten
wordengebruikt.
注意
• 必ず取扱説明書に従って本製品の組み立てを行って下さい。
• 本製品で定められた最大積載重量を超えないようにして下さい。最大積載重量をオーバーした
場合、怪我をする恐れや器物破損の恐れがあります。 本製品は、モニター1台あたり(2x8kg)まで
支持できます。
• 本製品は、室内での使用を想定しています。戸外では使用しないで下さい。

4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Cables(includingpowerandchargingcables)shouldbeplacedand
routedtoavoidcreatingelectric,trippingorsafetyhazards.
Mesures de sécurité
• Lescâbles(ycomprislescâblesd’alimentationetdechargement)
doiventêtreplacésetacheminésdefaçonàévitertoutrisque
électrique,dechuteoudesécurité
安全対策
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回し
を行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• Icavi(inclusiicavidialimentazioneediricarica)devonoessere
posizionatiestesiinmododaevitarepericolidiinciampo,rischidi
scosseelettricheopericoliperlasicurezza.
Säkerhetsåtgärder
• Kablar(inklusiveelkablarochladdningskablar)skadrasochplaceraspå
såsättattriskförsnubblingsolyckorochandraolyckorkanundvikas.

5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Warning Statements..............................................................................2
Safety Statements..................................................................................4
Product Diagram....................................................................................6
Product Dimensions................................................................................................................................. 7
Product Information..............................................................................8
Package Contents ..................................................................................................................................... 8
Product Specications............................................................................................................................. 11
Requirement ............................................................................................................................................... 12
Assembling the Monitor Mount...........................................................13
Mounting the Monitors.........................................................................17
Adjusting the Monitor Mount..............................................................20
Adjusting the Spring Arm Tension...................................................................................................... 20
Adjusting the Tilt ....................................................................................................................................... 22
Adjusting the Swivel................................................................................................................................ 23
Routing the Cables.................................................................................25
Using the 3.0 USB Passthough Ports...................................................27
Using the 3.5 mm Audio Port ...............................................................28

6
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
1VESA Holder 5Lower Arm
2Upper Spring Arm 6USB Ports and 3.5 mm
Audio Ports
3Cable Cover 7C-Clamp
4Cable Clip
1
2
3
4
5
6
7

7
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Dimensions
Note: The measurements displayed are maximum measure-
ments and are in mm/inches, unless otherwised specied.

8
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Information
Package Contents
Arm Assembly
Qty: 1
Upper Clamps
Qty: 2
Lower Clamps
Qty: 2
VESA Mounts
Qty: 2

9
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Rubber Pads
Qty: 2
M4 x 12 mm Screws
Qty: 8
M4 x 30 mm Screws
Qty: 8
Plastic Spacers
Qty: 8

10
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
4 mm Hex Key
Qty: 1
5 mm Hex Key
Qty: 1
M6 x 12 mm Screws
Qty: 8
M8 x 12 Screws
Qty: 4

11
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Specications
VESA
75 x 75
100 x 100
Rotation
- 3600to + 3600
Tilt
- 900to + 850
LB
kg
Total Weight (two monitors)
17.6 lb (2 x 8 kg)

12
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Screen Size
15” to 32”
Swivel
-900 to +900
Requirement
Tools
• Phillips Head Screwdriver x 1
Displays
• 15” to 32” Displays x 2
Optional
• USB Cables x 2
• USB Compatible Devices x 2
• 3.5 mm Headset

13
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Assembling the Monitor Mount
1. Align the four Screw Holes on the top of the Upper Clamps
with the four Screw Holes on the bottom of the Base of the
Arm Assembly.
Installing the Upper Clamps
2. Insert eight M6 x 12 mm Hex Screws through the Screw
Holes on the Upper Clamps and into the Screw Holes on
the bottom of the Base.
3. Using the 4 mm Hex Key, tighten the M6 x 12 mm Screws,
being careful not to over-tighten.

14
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the M6 x 12 mm Screws
4. Remove the backing from the Rubber Pads.
5. Apply the adhesive side of the Rubber Pads onto the
bottom of the Upper Clamps covering the M6 x 12 mm
Screws.
6. Align the two Screw Holes on the Lower Clamps with two
Screw Holes on the bottom of the Upper Clamps.

15
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Installing the Lower Clamps
7. Insert four M8 x 12 mm Screws through the Screw Holes on
the Lower Clamps and into the Screw Holes in the Upper
Clamps.
8. Using the 5 mm Hex Key, tighten the M8 x 12 mm Screws,
being careful not to over-tighten.

16
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Tightening the M8 x 12 mm Screws
9. Align the C-Clamp Assembly with the edge of the
Mounting Surface.
10. Slide the C-Clamp Assembly over the edge of the
Mounting Surface.
11. From underneath the Mounting Surface, tighten the two
Thumb Screws at the bottom of the C-Clamp Assembly.
Tighten the Thumb Screws until the C-Clamp Plate is
pressed tightly against the bottom of the Mounting
Surface.

17
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
C-Clamp Dimensions
Mounting the Monitors
1. Place the Monitor screen side down on a at, clean surface.
2. (Optional) Remove any Screws or Place Holders from the
VESA Mounting Holes on the back of the Monitor.
Note: Be careful not to remove any of the Screws holding
the Monitor’s Casing together.
3. Align the Screw Holes on the VESA Mount with the VESA
Mounting Holes on the back of the Monitor. The VESA
Mount can support 75 x 75 or 100 x 100 mounting pattern.

18
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Note When attached, the Arrow on the VESA Mount
should be point upward.
Aligning the VESA Mount with Monitor
4. Select the appropriate hardware for mounting the VESA
Mount to the back of the Monitor either M4 x 12 mm, M4 x
30 mm, or customer sourced screws.
5. Insert the appropriate Screws through the Screw Holes on
the VESA Mount and into the VESA Mounting Holes on the
back of the Monitor.
6. (Optional) For recessed surface mounting, align the four
Spacers with the VESA Mounting Holes on the back on the
Monitor, prior to securing the VESA Mount to the Monitor.

19
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
7. Using a Phillips Head Screwdriver (or appropriate
screwdriver) tighten the screws.
Note: Do not over-tighten the Screws. If you encounter re-
sistance while you’re tightening the Screws, stop tightening.
Failure to do so could result in damage to the Monitor.
8. Repeat steps 1 - 7 to install the VESA Mount of the second
Monitor.
Note: It is recommended that two people mount the Moni-
tors.
9. Pull the VESA Clip on the VESA Holder back towards the
Spring Arm.
Pulling back the VESA Clip