Steelcase 9000 Series User manual

Page 1 of 7
939503251 Rev C
Series 9000®Desk Adapter Kit
(Used for Mounting 22-5/8" D Pedestals Under 30"D Desks)
®
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2003 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
3/8" HEX
SOCKET
#2 PHILLIPS BIT
NOTE: For pedestals manufactured prior
to February 2004, use adapter kit 99239
per assembly direction 939501141.
Components
Tie Plate
#10 x 1/2" Self
Drilling Screw
(GQTFC)
Back Panel
Retainer
1/4-20 x 1/2"
Hex Head Screw
(853014765MP)
Adapter Bracket
For Package of all
Components above
(9U239)

Page 2 of 7
939503251 Rev C
1a
1b
1d
1e
1c
ACCESS CAP
RELEASE
TAB
OUTER END
PANEL
TAB
1.Remove outer end panel.
Remove access cap by pulling
upward on the left end cap (1a).
With your finger, move the
exposed release tab disengaging
top of outer end panel (1b).
With the top of outer end panel
tilted outward, lift up removing the
bottom tabs (1c). Flip desk over
onto a soft protective surface
(1d). Remove back panel (1e).

Page 3 of 7
939503251 Rev C
2.Attach adapter brackets to
worksurface channels using two (2)
#10 x 1/2" self-drilling screws
(GQTFC) per bracket.
2a
2b
2c
ADAPTER
BRACKET
#10 X 1/2" SELF-DRILLING
SCREW (GQTFC)

Page 4 of 7
939503251 Rev C
3/4” HEIGHT BACK PANEL
FULL HEIGHT BACK PANEL
TIE PLATE
#10 X 1/2"
SELF-DRILLING
SCREW (GQTFC)
3
4
3. If necessary, relocate back
panel to the recessed position.

4. Secure back panel to
worksurface using the tie plate
and three (3) #10 x 1/2"
self-drilling screws (GQTFC).
BACK PANEL
RETAINER
1/4-20 x 1/2"
HEX HEAD SCREW
(853014765MP)

Page 5 of 7
939503251 Rev C
7
8
Removal of Drawers
5. Pull drawer forward.
6. Push on tab on each side of the
drawer rails.
7. Remove drawer completely.

8. Push drawer rails back into
pedestal.
9. Remove remaining drawers.

TIP: Mark all drawers so they can be
easily re-installed in their original
positions.

10. Remove hanger bracket.
5
6
10

Page 6 of 7
939503251 Rev C
11
Pedestal Installation
11. Attach pedestal to worksurface
and adapter brackets using five (5)
1/4-20 x 1/2" hex head screws
(853014765MP) as shown.
12. Flip desk back over and replace
end panel covers.
13. Adjust end panel glides to level
the worksurface.
Bottom View of Pedestal
Showing Screw Locations
(Back)
(Front)
EXTRA SCREW IS
CLOSEST TO END PANEL

Page 7 of 7
939503251 Rev C
Drawer Re-Assembly

NOTE: Remember to re-install drawers in their
original positions.

1. Verify that drawer rails are pushed back into
pedestal.

2. Pull ball cages on drawer rails to front of
drawer rails.

3. Carefully align drawer portion of rail with ball
cage of pedestal portion of rail and gently push
drawer back into pedestal.

TIP: Failure to re-assemble drawers correctly
may damage rails, rendering them non-functional.
3
1
2