stilum caligo pluma 2014 User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „caligo pluma 2014“
Item No. 51 3018 401
State: 28.10.2015 p. 1
Diagram 1: Overall view of the play equipment

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „caligo pluma 2014“
Item No. 51 3018 401
State: 28.10.2015 p. 2
100
600
550 842
ok
600
Fertigung
51.3018.401-02
Fundamentplan
Federgerät - Caligo Pluma
Gru
25.07.2014
Maßstab 1:20
Allgemein-
toleranzen
DIN 7168-m
Bl.
A4
Norm
Gepr.
Bearb.
Name
Name
Datum
Datum
Änderung
Zust.
Diagram 2: Side view with dimension details „caligo pluma 2014“
Play level
Concrete foundation
Floor anchor
1. Select the play equipment location in consideration of the required safety
area (see Diagram 3: Ø 3500 mm).
2. The impact area of a playground equipment with an enforced movement is
not allowed to overlap the impact area of other equipment.
Regarding to DIN 1176 - 4.2.8.2.5, impact absorbing surfaces have to be put
under the whole impact area of every equipment with an enforced movement.
3. Carry out excavation work for the foundation anchor as shown in Diagram 2.
After excavation, compress the foundation oor.
Note: The springrider is built in on the play level. Pay attention to items
marked „game level“ of play equipment!
4. Grout the foundation oor with concrete of quality class B25 up to a
height of appr. 100 mm.
5. Insert the play equipment with foundation anchor into the concrete mass as
shown in the diagram, so that the base plate is surrounded by a concrete
thickness of at least 50 mm both above and below.
Reinforcement plan: Concrete foundation with rein-
forcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class B25

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „caligo pluma 2014“
Item No. 51 3018 401
State: 28.10.2015 p. 3
Diagram 3: Top view „caligo pluma 2014“
3500
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
Zust.
Änderung
Datum
Datum
Name
Name
Bearb.
Gepr.
Norm
A3
Bl.
Allgemein-
toleranzen
DIN 7168-m
Maßstab 1:20
25.07.2014
Gru
Federgerät - Caligo Pluma
Fallraumplan
51.3018.401-03
Fertigung
E
Extent of the minimum
zone = safety area
6. After a setting period of 8 – 10 days, depending on weather conditions and
foundation size, seal the foundation with the safety cover required for the
height of fall indicated. Set up impact-absorbing playground surfacing accor-
ding to EN 1177 HIC 1000.
Recommended surface material: grass, sand, bark mulch, gravel, synth. fall
protection. (Critical drop height ≤ 1000 mm)
7. Do not allow children to use the equipment before the installation has been
nished.
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to par-
ticular risks of injury for the user. For this reason, make clearly visible that the
equipment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may rub
off and leave small steel particles in combination with moisture brown rust stains.
If such corrosion occur on stainless steel parts, they are ne with an abrasive
(240 grit) to remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for springrider „caligo pluma 2014“
Item No. 51 3018 401
State: 28.10.2015 p. 4
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type
and degree of soiling as well as on demands made on optical characteristics.
Therefore cleaning is advisable at intervals of six to twelve months – whereby in
the case of strong soiling it is appropriate to clean the playground equipment at
intervals of 3 to six months.