stilum funis User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for cableway „funis“
Item No. 517021101
State: 10/10/2014 · S. 1 · MS/TSA
Lateral pole
Pendulum seat
Cable car
Steel cable
Diagram 1: Overall view of play equipment with description of individual elements

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for cableway „funis“
Item No. 517021101
State: 10/10/2014 · S. 2 · MS/TSA
Mounting instructions for cableway „funis“
Foundation
Diagram 2: Side view with dimension details of „funis“
Diagram 3: Top view
Play level
Brake spring
Brake spring
Extent of the minimum zone =
safety area
1. Select the play equipment location in consideration of the required safety
area (see Diagram 3: 34000 x 4000 mm).
2. Carry out excavation work for 2 foundations as shown in Diagram 2.
3. After excavation, compress the foundation oor. Note: The cableway is only
available with an installation depth of 450 mm. Pay attention to items marked
„game level“ of play equipment!
4. Set up concrete foundations in the dimensions indicated (LxWxH 3400 x
1200 x 600 mm) and integrate reinforcement as shown in the plan (see plan)
in the quality class B 25. Insert the pre-mounted cable car into the foun-
dations in accordance with the dimensions indicated. Make sure that the
concrete between the tubes of the poles is also compressed properly (see
Reinforcement Plan).
No warranty for damage to backwater or condensation in the tube. Adequate
drainage in the foundation is necessary.
5. Align the cable car horizontally and vertically and keep it supported until the
foundations have completely set. Note: Do not allow children to use the cable
car as long as it is supported.
6. After a setting period of 10-14 days - depending on weather conditions and
foundation size - seal the foundation with the safety cover required for the
height of fall indicated. Set up impact-absorbing playground surfacing accor-
ding to EN 1177 HIC 1000.

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for cableway „funis“
Item No. 517021101
State: 10/10/2014 · S. 3 · MS/TSA
Mounting instructions for cableway „funis“
7. Mould the area around the equipment as shown in Diagram 2.
Recommended surface material: grass, sand, bark mulch, gravel, synth. fall
protection. (Critical drop height ≤ 1000 mm)
8. Fasten the rope to the eyelet and hang in the brake springs (brake spring at
the exit: 3000 mm – brake spring at the start: 1000 mm) and the cable car.
Mount the chain tightener, screw the rope onto it and tighten the rope bytur-
ning the chain tightener (rope sagging of 1% - max. 2%).
9. Important note: Minimum distance of seat (with load) to ground is 400
mm!
10. The brake spring at the exit has to be  xed in such a way that with a load of
130 kg on the seat and with a de ection of 45° a barrier-free space of 2.00 m
is still guaranteed (see Diagram 5).
11. Hang the swing seat into the cable car and fasten it with screws.
12. Do not allow children to use the equipment before the installation has been
nished.
Diagram 4: Reinforcement Plan
C 25/30, XC 2, XF 1, 3400 / 1200 / 600 mm mit Mindestüberdeckung (Sand) 450 mm
Reinforcement cage Bü.-Ma. R 188 A, with 6 bars Ø 12 mm above and below, provide
case for supports or embed one directly in concrete
2 x 1500 mm = 3 x BüMa R 188 A, 2150 x 3500 mm
2 x 12 = 24 bars Ø 12 mm, l = 3800 mm
Reinforcement Plan
1
1
1100 mm
500 mm
150 mm
150 mm

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved.
Mounting instructions for cableway „funis“
Item No. 517021101
State: 10/10/2014 · S. 4 · MS/TSA
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to particu-
lar risks of injury for the user. For this reason, make clearly visible that the equip-
ment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel should
not come with „normal“ steel parts in contact. Those steel parts may rub off and
leave small steel particles in combination with moisture brown rust stains.If such
corrosion occur on stainless steel parts, they are ne with an abrasive (240 grit) to
remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.
In order to preserve a good visual appearance of your stilum playground equip-
ment over a long period one should take care of maintenance of the stainless
surface even despite of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type and
degree of soiling as well as on demands made on optical characteristics. Therefore
cleaning is advisable at intervals of six to twelve months – whereby in the case of
strong soiling it is appropriate to clean the playground equipment at intervals of 3
to six months.
Diagram 5: Installation brake spring
A
45°
2100
DETAIL A
MAßSTAB 1 : 50
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
MAßSTAB:
KUNDE:
BESTELL-NR:
Auslenkung 45°
Funis
ZG-NR:
BENENNUNG:
V. Bishop
FREIG:
GEPR:
GEZ:
NAME:
DATUM:
WERKSTOFF / ROHMAß:
1:200
ZUL. ABWEICHUNG
DIN 2768 - mH
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
WERKSTUECKKANTEN
NACH DIN 6784
-0,3
+0,3
25.11.2009
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A4
A
45°
2100
DETAIL A
MAßSTAB 1 : 50
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI + KAISER GMBH DARF DIESE TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT
NOCH DRITTEN MITGETEILT ODER ZUGÄNGLICH GEMACHT WERDEN NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VERWENDET
WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
MAßSTAB:
KUNDE:
BESTELL-NR:
Auslenkung 45°
Funis
ZG-NR:
BENENNUNG:
V. Bishop
FREIG:
GEPR:
GEZ:
NAME:
DATUM:
WERKSTOFF / ROHMAß:
1:200
ZUL. ABWEICHUNG
DIN 2768 - mH
OBERFLAECHEN NACH
DIN ISO 1302 REIHE 2
WERKSTUECKKANTEN
NACH DIN 6784
-0,3
+0,3
25.11.2009
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland
A4