stilum supra 2 User manual

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 15.02.2019 p. 1
Mounting instructions for horizontal bar „supra 2“
Item No. 55 1515 402
Diagram 1: Overall view of „supra 2“

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 15.02.2019 p. 2
Mounting instructions for horizontal bar „supra 2“
Item No. 55 1515 402
Legende
Erde, Grund
Ground
Beton
Concrete
Füllmaterial
Filling
700
500
450
450
Freie Fallhöhe =
1370
Einbautiefe 450mm
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
Zust.
Änderung
Datum
Datum
Name
Name
Bearb.
Gepr.
Norm
A3
Bl.
Allgemein-
toleranzen
DIN 7168-m
Maßstab 1:20
04.12.2014
Kistinger
Supra 2
0134-00-00-Supra 2
0134-00-00
Fertigung
E
1. Select the play equipment location in consideration of the required safety
area (see Diagram 3: 2500x 3000mm).
2. Carry out excavation work for the foundation as shown in Diagram 2. After
excavation, compress the foundation oor.
Note: The horizontal bar is built in on the play level. Pay attention to items
marked „play level“ of play equipment!
3. Set up the three concrete foundations acc. to the dimensions indicated in
Diagram 2 with central, horizontal reinforcement.
4. After a setting period of 10-14 days, depending on weather conditions and
foundation size, clean the surface of the foundation.
5. Place the pre-assemled sport equipment on the foundation and screw it with
the heavy-duty dowels included in the delivery.
6. Fill up and compress the holes between the foundation and the foundation
hole with the excavation.
7. Seal the whole minimum zone/safety area with the impact protection required
for the fall heights indicated. Set up impact-absorbing playground surfacing
according to EN 1176-1.
Critical drop height: 1400mm
Recommended surface material: sand, wood chips, gravel,
synth. fall protection
8. Do not allow children to use the equipment before the installation has been
nished.
Reinforcement plan: Concrete foundation with reinforcement
Main foundation: BSt 500S
Ever 4 stirrups Ø 8 mm lengthwise and cross
Concrete cover h´= 3 cm
Concrete quality class C20/25
Diagram 3: Top view
Extent of the minimum
zone = safety area
Diagram 2: Side view with dimension details „supra 2“
Legende
Erde, Grund
Ground
Beton
Concrete
Füllmaterial
Filling
700
500
450
450
Freie Fallhöhe =
1370
Einbautiefe 450mm
D
E
F
C
1 2 3 4
B
A
3 2 1 5
C
D
4 6 7 8
A
B
Zust.
Änderung
Datum
Datum
Name
Name
Bearb.
Gepr.
Norm
A3
Bl.
Allgemein-
toleranzen
DIN 7168-m
Maßstab 1:20
04.12.2014
Kistinger
Supra 2
0134-00-00-Supra 2
0134-00-00
Fertigung
E
2500
3000
OHNE SCHRIFTLICHE ZUSTIMMUNG DER CONRADI+KAISER GMBH DARF DIESE
TECHNISCHE UNTERLAGE WEDER VERVIELFÄLTIGT, NOCH DRITTEN MITGETEILT ODER
ZUGÄNGLICH GEMACHT WERDEN, NOCH IN SONSTIGER WEISE MISSBRÄEUCHLICH VER-
WENDET WERDEN. ZUWIDERHANDLUNGEN WERDEN URHEBERRECHTLICH VERFOLGT.
Oberflächen nach DIN ISO 1302 Reihe 2
Zul. Abweichung DIN 2768 - mH
1
supra 2 (450)
Benennung
Gepr.
Werkstoff
Blatt
Datum
Projekt
Gez.
Zuschnitt
Zeichnungsnummer
Rev Änderung Datum
1:20
A3
Gewicht
Name
Name
Draufsicht
2104-00-00
28.96
Maßstab
Simonis
02.05.18
A
Fallraum kleiner
14.02.19
ES
Gewerbegebiet Larsheck
56271 Kleinmaischeid
Deutschland

© stilum GmbH, Gewerbegebiet Larsheck, 56271 Kleinmaischeid • Tel. [phone] • All rights and product modications reserved State: 15.02.2019 p. 3
Mounting instructions for horizontal bar „supra 2“
Item No. 55 1515 402
Attention: If the play equipment has been incompletely installed or partly dis-
mantled when carrying out maintenance and repair work, this may lead to par-
ticular risks of injury for the user. For this reason, make clearly visible that the
equipment shall not be used in such cases.
NOTE: Play equipment, which contain components made of stainless steel
should not come with „normal“ steel parts in contact. Those steel parts may rub
off and leave small steel particles in combination with moisture brown rust stains.
If such corrosion occur on stainless steel parts, they are ne with an abrasive
(240 grit) to remove.
Please take care when transporting and setting up the fact that the components
are made of stainless steel with no „normal“ steel parts in contact.In order to pre-
serve a good visual appearance of your stilum playground equipment over a long
period one should take care of maintenance of the stainless surface even despite
of their corrosion resistance.
Especially areas, which can not be reached by rainfall should be frequently clea-
ned from dirt and deposits due to air pollution and dirt caused by the atmosphere.
Light soiling can easily be romoved by using a high pressure cleaner.
For persistent deposits use a clean cloth moistened with a special liquid cleaner
(e.g. on phosphoric acid) and rinse off with clear water after a short application
time. During cleaning with mild abrasive components, only wipe over stainless
steel surface in polishing direction.
For heavily soiled surfaces, polishes can be used (e.g. for cleaning chrome on
cars) or for greasy and oily dirt alcoholic cleaning agents and solvents (e.g. ethyl
alcohol, isopropyl alcohol or acetone).
However, it should be noted that the dissolved soiling is not spread over the sur-
face again.
Do not use any chlorid or hydrochloric containing cleaning products nor scouring
powder, bleaching - or silver polish cleaner. Cleaning intervals depend on type and
degree of soiling as well as on demands made on optical characteristics. Therefore
cleaning is advisable at intervals of six to twelve months – whereby in the case of
strong soiling it is appropriate to clean the playground equipment at intervals of 3
to six months.