Storehouse 93198 User manual

Copyrigh t © 2 005 by Harbor FreightTools®.All rights reserved.No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions and replacement parts, please call 1-800-444-3353
ASSEMBLY INSTRUCTIONS
93198
BIN RACK
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit ourWeb site at http://www.harborfreight.com
Due to continuing improvements, actual product may differ slightly from the
product described herein.

SKU 93198 For technical questions, please call 1-800-444-3353. Page 2
Specifications
Save This Manual
You will need the manual for the safety warnings and precautions, assembly
instructions, operating and maintenance procedures, parts list and diagram.
Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep the manual and invoice in a safe and dry place for future
reference.
Safety Warnings and Precautions
WARNING: When using product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
3. Check for damaged parts. Before using any product, any part that
appears damaged should be carefully checked to determine that it will
perform its intended function. Check for any broken or damaged parts and
any other conditions that may affect its operation. Replace or repair
damaged or worn parts immediately.
4. Replacement parts. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
5. Always check hardware and assembled parts after assembling. All
connections should be tight and hardware tightened.
6. Keep children away. Children must never be allowed in the work area.
Small objects stored in Bins could be swallowed by small children.
Materials
Assembled Dimensions
Bin Inside Dimensions
Color of Bins
Weight Cap.
Net Weight
Molded Polyethylene Plastic Bins–Stack-able –Qty. 15
13” H x 10-1/4”W
5” Depth x 3.5”W x 2.83” Deep
Yellow-Qty. 5; Red-Qty. 5; Blue-Qty. 5
5 Lbs. Capacity per Bin
7.70 Lbs.

SKU 93198 For technical questions, please call 1-800-444-3353. Page 3
7. Use eye protection. Always wear ANSI approved impact safety goggles
when setting up this product.
8. Maintain products with care. Keep the Bin Rack clean for better and safer
performance. Follow instructions for set up. Inspect periodically.
9. Do not overload the Bin Rack. The weight capacity is 5 lbs. per bin.
Warning: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may oc-
cur. It must be understood by the user that common sense and caution are
factors which cannot be built into this product, but must be supplied by the
user.
Unpacking
When unpacking this product, check to make sure that all parts are included
as shown in the parts list. If any parts are missing or broken, please call
Harbor Freight Tools at the number below.
Assembly
1. Attach the right and left Stands (2) to the
Rack (1), using Bolts (7), Washers (6) and
Nuts (8). See Figure 1 and Parts
Diagram on Page 5.
2. Tap the Plugs (5) on each end of the
Stands (2), right and left. (Qty.4).
See Figure 1.
Figure 1
Rack (1)
Stand (2)
Bolt (7)
Washer (6) (qty. 2)
Nut (8)
Plug (5)

SKU 93198 For technical questions, please call 1-800-444-3353. Page 4
3. Place the colored Bins (4-1, 4-2 and 4-3) over the hooks on the Rack (1) by
lifting up and clicking into place at the back of the individual Bins. See
Figures 2 and 3.
4. Be careful not to overload the individual Bins, especially the ones at
the top.This could cause the Bin Rack to tip over.
Figure 2
Figure 3
5. After assembly, you can slip a label (not provided) for each Bin in the Name
Plate Holder (3) on the front of each Bin. (example: Nut M5, Washer 5mm,
Bolt M5x10, Nails, etc.) The Name Plate Holder (3) slips off the Bin and can
be snapped back in place after the label has been placed between the plastic
sleeve.The Bin Rack can also be used to organize craft products or other
small objects. See Figure 3.
Red Bin (4-1) Rack (1)
Blue Bin (4-3)
Yellow Bin (4-2)
Name Plate
Holder (3)

SKU 93198 For technical questions, please call 1-800-444-3353. Page 5
Parts Diagram
1. To remove dust, use a damp cloth.To remove grease or oil, use a detergent
based cleaning solvent, rinse and dry with a cloth.
2. This product should be stored in a dry area.
Maintenance

SKU 93198 For technical questions, please call 1-800-444-3353. Page 6
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BYTHE BUYER.THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE-
MENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.
Parts List
1
2
3
4-1
4-2
4-3
5
6
7
8
Part # Description Qty.
Rack
Stand
Name Plate Holder
Red Bin
Yellow Bin
Blue Bin
Plug
Washer 5mm
Bolt M5X10
Nut M5
1
2
15
5
5
5
4
8
4
4
Part 2
Part 1
Part 4-1
Part 4-2
Part 4-3 Parts 6,7,8
Part 3
Part 5
Parts Identification