STREETER SUPER LIFT User manual

SUPER LIFT ASSEMBLY GUIDE
streetersuperstands.com
TECH/ORDER LINE: [phone]

Thank You and Congratulations on your purchase of a Streeter Super Stands SUPER LIFT. This booklet is the basic
guide for assembly of your stand. Minimal mechanical knowledge and standard tools are all that will be neded for the
assembly procedure. Please familiarize yourself with this booklet, the included components and your stand prior to
beginning the assembly. On average, most users can complete this assembly and setup within an hour. If you have
any questions or need technical assitance with your SUPER LIFT, contact us at [phone].
Your Streeter Super Stands SUPER LIFT was packaged and shipped in two separate boxes. Upon arrival and removal
from packaging, you will have received:
Control Handle Assembly
DO NOT remove the colored cable tires located on the ends of the wires on
the control handle.
Super Lift Base (with winch) and arms
Hardware kits and bolts
Battery cover and mounting bolts
Front wheels and rear casters
View of included hardware:
*Packaging may dier than shown*
Control handle mounting bolts (2 short, 1 long)
Axle Studs (will be either SILVER or BLACK in color)
Caster and wheel mounting hardware (8 each of nuts, washers and bolts)
& (2 axle nuts for front wheels)
Lift hooks (2) and mounting hardware.
Battery cover, carraige bolts and battery
cable connection bolts
streetersuperstands.com

Thread short end of front axle studs into
the stand. The use of a “blue”thread
locker is suggested. Tigthen each axle/
stud.
Install wheels and tighten each axle nut.
Once tightened, back-o (loosen) nut
just enough so the wheel spins freely.
Install casters and tighten mounting bolts. Some users prefer to position the
base of their stand on its side or lay it upside down during this process. While
installing casters, it is a great time to check the tightness of the (4) bolts on
each caster that hold the wheel to the hub -as to verify they did not loosen
during packing and shipping. Casters should be lubed prior to use and
periodically there after for optimum performance.
Remove terminal cover located on the
bottom of the stand base. Notice that
they are together and matched with
colored cable ties. DO NOT remove the
cable ties on these wires!
There should be NO battery or power of
any kind hooked up to the stand at this
time!
Slide wires from handle assembly through
access hole in frame and in to the terminal
connection area. DO NOT remove the colored
cable ties on these wire!
Losen screws on the empty terminal spots.
streetersuperstands.com

streetersuperstands.com
The two short bolts with nuts will be
used to attach the lower portion of the
handle to the bottom of the stand base.
The longer bolt with nut will attach the
handle to the upper portion of the base.
Strip wire ends on the handle wires and
match up wires to those already installed
in the terminal connector. Match the
colored cable ties and match the corre-
sponding wire colors together. DO NOT
remove the colored cable ties.
Yellow colored cable tied red and black
wires should be installed to match those
in the terminal.
Orange colored cable tied red and black
wires should be installed to match those
in the terminal.
Tighten screws and check to make sure
wires are secure within the terminal.
When this is complete, re-install the
cover plate.
Remove nut, bolt and washers from each
of the stands arm assemblies.
Install arm assemblies onto the base and
insert washers, bolt and nut.
Tighten accordingly, though making sure
the arms freely pivot.

streetersuperstands.com
Chains are semi-installed on the stand.
You will need to tighten the bolts that
attached them to the stand arms. Make
sure the chain links are not kinked and
that each side is extended equal.
Turn the winch knob to“Free Wheel”
mode. The drum should be able to
rotate as to pull the strap (AS NEEDED in
the next steps) out from the spool/drum.
Winch strap should be ran as shown. Un-
der the inner frame rail and in between
the handle post and roller.
Do not pull excessive strap from the
spool/drum.
Do not pull excessive strap from the
spool/drum.
Pin and roller on upper portion of the
stand is then removed and then re-
installed going through the loop of the
winch strap.
Re-spool any possible excessive strap
that may have been pulled out. Upon
conrmation of this and proper rout-
ing, the winch can be taken out of“Free
Spool” mode and back to engagement
mode.

streetersuperstands.com
Install lift hooks, though these will have
to be adjusted to within the dimensions
of your rear bumper. Adjust as needed
and tighten. Streeter Super Stands Super
Lift hooks are designed to work with the
majority of bumpers currently in use.
Hooks are designed to easily adjust up,
down, in and out on your stand. Use the
best pick up point on your bumper for
the most smooth secure operation.
Your Super Lift will use a U1 group sized
battery (lawn tractor type). Suggested
batteries used for a Super Lift are:
Farm & Fleet U1R300 300 CA
Fleet Farm U1R
Tractor Supply GT-X / GT-H
Sears/DieHard U1 / UR1
Wal*Mart U1R7
We also suggest using:
Schumacher SEM-1562A 1.5 amp Battery
Charger/Maintainer.
A proper sized battery will t right in
the tray. Install battery cables inward as
shown. Always double check t before
install.
Slide bottom lip of battery cover under
the battery cables.
Cable tie battery cables together using
provided cable tie or similiar.
Install carriage bolts and tighten battery
cover to base of stand.
Protective ap will be held in place by
hooks on battery hold down cover as
shown.
Standard Battery Dimensions:
7.50 wide x 5.19 depth x 7.19 height (includes posts)
Hooks are designed to work with the majority of existing styles of bumpers.
Check t prior to use. Sometimes, hook adjustments or modication may be
required. If you have questions regarding hooks and their use, please contact
Streeter Super Stands directly. [phone]

streetersuperstands.com
Your Super Lift comes with Arm Stop Ad-
justing Bolts located on the main base.
These are preset at the factory, however
you may need to adjust as needed for
your kart/use. The arms of the stand will
need to sit far enough back to prevent
the stand/winch from pivoting forward
on its own, though not far enough back
as to come in contact with the control
handle.
This is an important step in the assembly of your Super Lift and we suggest
you follow it:
At this time you should grab a favorite beverage of your choice. Find a nice
comfy chair close to your Super Lift. Enjoy your beverage and admire the
completed Streeter Super Stands Super Lift before you. It is now from this
moment forward that your racing endeavours will be easier and your family
and friends will be ever so happy as to not have to help lift your kart. Cheers
to You and Thank You for your purchase of a Streeter Super Stands product!
We appreciate your purchase and of course we fully back our products, however the assembly, care, use and proper operation
of this stand is your responsibility. Do not attempt to lift your kart unless you are sure of the lifting hooks position and you are
also comfortable with the use of this stand. The potential for injury is present and the user accepts all liability as such. Streeter
Super Stands is not responsible for personal injury, any damage to the stand, kart or surroundings due to misuse or wrongful
assembly. User is responsible for the proper assembly, usage and care of the stand. Never exceed the intended use and capacity
of the stand. Streeter does not condone nor oer warranty or reimbursement of damage to stand or items from transport of kart
on stand- user assumes all risk.
Need further assistance or
additional items for your Su-
per Lift? Contact us at (262)
457-5018

streetersuperstands.com
SUPER LIFT ACCESSORIES & OPTIONS:
LOWER STORAGE / PARTS TRAY (part# STR-2800-506)
Keep your mini-starter, tools or parts located with your Super
Lift. The large tray securely bolts to the main base of the stand
and looks great in a matching silver poweder coat and comes
with a rubber pad insert to protect the tray and your tools.
UPPER STORAGE / PARTS TRAY (part# STR-2800-511)
The Super Lift Upper Tray ts all model year Streeter Super Lifts,
quickly attaching to the Control Handle bars. This handy tray is
nice for tool and parts storage when working in the pits or post-
race tech. The center section will hold a water bottle, pop or
your favorite beverage. Durable black powder coat looks great
with any color Super Lift
AIR TANK HOLDER (part# STR-2800-509)
A great solution and very handy idea for storing your air tank
right on your Streeter Super Stands Super Lift. Aluminum Air
Tank Holder bolts directly to your Super Lift and holds most
standard (up to) 5 gallon air tanks. Check t of your own air tank
(needs to clear the silver arms when lowered) or purchase the
air tank listed below to be assured of proper t.
AIR TANK (part# STR-2800-510)
This 5 gallon steel portable air tank is great for at home, at the
track and ts our Super Lift Kart Stand Air Tank Holder perfectly.
Red in color, with Streeter logo. Comes with shut o valve and
gauge.
MORE NEW ACCESSORIES COMING SOON!