Stryker T-Tops SG300 User manual
SG300 INSTALLATION GUIDE
& OWNER’S MANUAL
KIT INCLUDES:
SG300 T-TOP FRAME
SUNBRELLA®CANOPY
MOUNTING HARDWARE
IMAGE SHOWN WITHOUT CANOPY FOR CLARITY
SG300
SG300
SG300
SG300
SG300
SG300
SG300
SG300
SG300
SG300
Proper Usage & Safety
For your safety and everyone else, plus, to avoid damage to your Stryker T-Top and boat, please read and
observe the following. Make sure all bolts and screws are properly torqued down. Over time, vibrations can
loosen them up so it is important to retighten everything periodically. Do not use the t-top to tow
wakeboarders, skiers, knee boarders, inflatables or tubes. Do not trailer your boat with the t-top folded down.
When trailering your boat, make sure it is in the upright position and pay close attention to clearance
limitations like low bridges, car port covers, tree branches, etc. Be sure to measure the highest point of your
t-top or mounted accessories before hitting the road.
Do not attempt troll fishing with lines or rods cast from the t-top. When the boat is in motion either in the
water or on a trailer, be sure to take down any rods, outriggers or other items that might conflict with
clearance heights on your route. Stryker T-Tops is not responsible or liable for damage due to a customer’s
misuse of our products or negligence.
Wiring Instructions
You can easily wire your Stryker T-Top to connect lights, antennas, speakers or other electronics. The frames
are hollow and are a perfect place to keep wires tucked out of sight and away from the elements. Careful
planning will help you avoid the cleanest installation without unnecessary drilling or miscalculations.
Start by drilling a hole where you want the accessory mounted to the tubing. If mounting to the top “hoop”
section that the canvas ties to, start by feeding the wire into the tubing at that location. Work the wire
through towards the middle of the top sections where the leg sections clamp. The clamps are solid billet
aluminum but have a predrilled hole for wires. This is how you will get the wires down towards the deck. Drill
an exit hole in the top section that is in line with where your clamps are located.
Note: you will have to have your t-top completely installed to know exactly where your leg section clamps will
be located relative to the top section.
Once aligned, you can feed the wire exiting the top section down through the middle of the leg section
clamps. Continue working the wires down the leg section closest to the bow. Be sure to plan ahead, know
where the terminals on the boat are located and know if it’s better for you to run wires down the port or
starboard leg.
The most important thing to know is that the joints that connect the top and bottom leg sections are solid
billet aluminum and must be bypassed. They are not pre-drilled like the top clamps. Do not attempt to drill
through these sections as it could compromise the strength of the joints.
To bypass them, you will need to drill an exit hole and re-entry hole around the joint. Make a 1” hole about
1.5” away from the weld line. To keep water out, we recommend picking up some rubber grommets that fit
the holes you are drilling. Also, give yourself a little extra slack in the bypassing wire especially if you have a
t-top model that folds. This is another good reason to run the wires down the leg section tubing closest to the
bow since that is the folding joint on certain models.
Lastly, most of our customers exit the wire out of the bottom of the leg section with one more drilled hole
and another rubber grommet. From there, you can run the wire to where you need to connect it. Once
everything is complete, we recommend putting a little silicon caulking on the rubber grommets around the
wire to prevent water from getting inside the tubing.
SG300
Center Console Units with a Hinged Door
If your boat’s center console unit has a hinged door, you shouldcarefully measure thesizeand clearance
required to fully open it. Depending on the Stryker T-Top model, the lower leg sections might have a
horizontal brace that could prevent the door from opening. On the SG300, this braceiswelded on; the SG600
has a brace that is mounted with allen head bolts and can betemporarily removed; the SG900has been
designed with a much higher horizontal brace to avoidthis situation.
Probably the simplest solution, some of our customers have replaced their door hinges with pins. This allows
the door to be pulled out without swinging it open. However,you will still need toconsider how the
horizontal brace with affect your access to the inside of the console unit. Please contact us with your door’s
measurements sowe can help figureout the best solution basedon your needs.
Care & Maintenance
Properly cleaning your Stryker T-Top products with greatly extend the life andmaintaintheir value! We
recommend more frequent light cleaning. This will avoid a build-upof grime and deposits that will require
stronger cleaning and harsher cleansers.
GENERAL CLEANING T IPS
• Over-cleaning or excessive rubbing can do more harm than good.
• To prevent marring, make sure your sponges, microfiber cloths, pads, etc, are clean and grit-free.
• Only use clean water. Dump and refill bucket regularly to remove abrasive dirt and contamination.
• Avoid abrasive or household cleaners that can cause permanentdamage to painted surfaces.
• Avoid abrasive materials such as steel wool, scouring pads, hard bristle brushes, etc.
• When using recommended solutions avoid drips and splashes. Remove run downs as quickly as possible.
• Avoid temperature extremes. Heat accelerates chemical reactions and may evaporate water from solution.
Extremely low temperature may give poor cleaning effects.Cleaningunder adverse conditions may result in
streaking or staining. Ideally, cleaning shouldbedone in theshade at a moderate temperature.
• Do not substitute a heavy duty cleaner for a frequently used mild cleaner.
• Do not scour painted surfaces.
• Never use paint removers, aggressive alkaline, acid or abrasive cleaners.
• Always do a test on a small hidden area before treating the entire surface.
• Follow the manufacturer’s instructions for applying, mixing, diluting, etc.
• Never mix cleaners.
A N ODIZED A L UMINUM C A R E
You can save yourself a lot of timeand unnecessaryextra effort bysimply committing to aregular, stress-free
cleaning regimen. Frequent light cleaning goes a long way to avoiding deposit build-up, etching or other ugly
conditions that require lots of elbow grease and harsher cleaning methods.
Start by determining the condition of the surface and how long it has been since the last cleaning.
If it’s just dirty, you can wash down anodizedaluminum with a mild soapy solutionor with warm water
containing a suitable wetting agent. Rinse with clean water anddry everything with a clean micro fiber cloth.
SG300
Care & Maintenance (continued)
ANODIZED ALUMINUM CARE
Because anodizing creates a hard finish, mild abrasives or an abrasive cleaning sponge is sometimes
recommended. More difficult grime deposits may also require the use of a mild abrasive.
BE VERY CAREFUL with whatever you use for medium to heavy cleaning! Start with a small hidden spot. Make
sure the surface is cool, out of direct sunlight and always follow the instructions on the bottle. Some of our
customers have had success using either Woody Wax Kit http://www.woody-wax.com/woody-wax-kit.php or
Flitz Liquid Polish: https://www.flitz.com/flitz-polish-liquid/
DO NOT use harsh acidic or alkaline cleaners because they may destroy the finish permanently. Use solvents
with care as they may stain, discolor or erode the finish. Remember to be thorough and clean all surfaces, all
sides, all corners and every nook. Also, thoroughly rinse with clean water especially where crevices are
present to ensure removal of all residues. If improperly rinsed, residual cleaning agents can lead to etching or
discoloration. Dry everything with a clean micro fiber cloth.
For more difficult condition issues, please either contact us or your local professional.
POWDER COATING CARE
You can save yourself a lot of time and unnecessary extra effort by simply committing to a regular, stress-free
cleaning regimen. Frequent light cleaning goes a long way to avoiding deposit build-up, etching or other ugly
conditions that require lots of elbow grease and harsher cleaning methods.
The best method of cleaning any powder coated finish is by regularly washing it using a solution of clean
water and a mild detergent. The entire surface- including all the nooks and corners- should be cleaned using a
soft cloth or sponge, using nothing harsher than a natural bristle brush. This will remove any dirt, minerals and
residue that could scratch or etch the finish. Rinse with clean water and dry with a micro fiber cloth.
If the atmospheric pollution has resulted in heavy soiling of the coating that is difficult to remove, then
nothing harsher than white spirit should be used for cleaning. Make sure the surface is cool and out of direct
sunlight. Always test in a less visible spot before treating the entire surface.
DO NOT use abrasive pads, steel wool or other hard textured mediums because they could permanently
destroy the finish. There are a variety of “powder coating polish” products on the market that are specifically
designed to polish and protect. Carefully follow the manufacturer’s instructions.
For more difficult condition issues, please either contact us or your local professional.
SG300
Warranty Information
WE TAKE PRIDE IN THE QUALITY OF OUR MANUFACTURING PROCESS AND MATERIALS. WE INSPECT
EVERY PRODUCT BEFORE IT IS SHIPPED TO ENSURE OUR STRICT STANDARDS ARE MET.
Stryker's 5 year warranty starts from the purchase date and covers defects that have occurred during the
manufacturing process. Following a physical inspection that determines a valid warranty claim, Stryker will- at
its discretion- replace, send replacement parts or reimburse for the repair of any eligible products. The
anodized or powder coated finish and hardware are excluded from the warranty coverage. Stryker is not
responsible for personal injury, boat damage or equipment loss directly or indirectly related to our products.
This warranty does not cover damage due to acts of God (fire, flood, lighting, etc.) nor product misuse and
accidental damage. Any cost of shipping and installation related to the return and replacement of products is
the responsibility of the customer unless otherwise deemed by Stryker. Stryker T-Tops disclaims any warranty
of merchantability or fitness for a particular purpose in connection with the Buyer’s purchase of units of any
Product under this agreement. For any products we sell but do not manufacture, that product's manufacturer
warranty applies and RMA requests must be made with them.
Defects must be reported within 30 days from the receipt of purchase.
Your new product was manufactured and assembled to meet the strict quality standards of the original
manufacturer. We ship thousands of products every year to customers who are very happy with the quality
and craftsmanship of our products.
Due to the nature of aluminum and stainless steel manufacturing and welding, some minor blemishes,
scratches and/or nicks may be visible on the product. SUCH MINOR BLEMISHES, SCRATCHES AND/OR NICKS
ARE NORMAL AND ARE NOT A VALID REASON TO RETURN A PRODUCT. If you believe that your product
shows excessive blemishes, scratches or nicks, you must send us an email within 3 days stating your concern.
DO NOT WAIT TO INSPECT YOUR PARTS! Your email must include photographs that clearly shows the size,
pattern and location of the blemish, scratch and/or nick.
As you are unboxing all the product parts, be very careful not to misplace any small parts or hardware.
All Stryker T-Tops and accessories have been carefully designed, manufactured and tested to meet the
highest standards of quality and performance to be extremely well-suited for a specific purpose. If any
product is found to have been modified, altered, incorrectly installed, mistreated, neglected, improperly
maintained, used for purposes it was not originally intended for or used beyond its physical limitations of
design or material, any and all warranties will be deemed void. The warranty period shall not be extended by
the replacement of materials under this warranty but the remaining warranty period shall continue in effect
and be applicable to the replaced or repaired products or component parts areas under conditions of the
warranty.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THOSE CONCERNING MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS LIMITED WARRANTY IS ALSO IN LIEU OF ANY OTHER POSSIBLE LIABILITIES OF THE SELLER OR
MANUFACTURER, WHETHER ALLEGED TO ARISE BY AGREEMENT OR BY OPERATION OF LAW.
RESPECTING THE SALE , APPLICATION, USE OR FUNCTION OF PRODUCTS, INCLUDING BUT NOT LIMITED
TO CLAIMS OF NEGLIGENCE, GROSS NEGLIGENCE, STRICT LIABILITY OR ANY OTHER TORT. IN NO EVENT
SHALL THE SELLER OR MANUFACTURER BE LIABLE FOR PERSONAL INJURY OR PROPERTY DAMAGE, REAL
OR PERSONAL, ATTRIBUTED TO ITS PRODUCTS, NOR FOR ANY EXCAVATION, REMOVAL, REAPPLICATION,
DOWNTIME, CLEANUP, LOSS OF USE, LOSS OF OPPORTUNITY, LOSS OF MARKET VALUE, LOSS OF RENTAL
VALUE OR FOR ANY LOSS OF PROFITS OR OTHER SPECIAL, INCIDENTAL, RESULTING, CONSEQUENTIAL
OR EXEMPLARY DAMAGE.
SG300
Product Returns
Goods can be returned by the ORIGINAL PURCHASER at their expense within three (3) days of the date of
DELIVERY with no questions asked for a full refund of the purchase price (less shipping, labor, special order,
and non-certified funds charges) provided the product(s) are in original new condition, in their complete
original packaging and have not been installed.
If for any reason you're dissatisfied with your purchase, we will replace the product or refund your purchase
price within 30 days of purchase date from strykerttops.com. Note that returns must be in original packaging
and in new, resalable condition otherwise a 25% restocking fee will be added. Damaged or unsalable products
will not be accepted. All packaging, shipping and insurance costs incurred to return products to Stryker
T-Tops are the responsibility of the purchaser and will not be credited. Original shipping fees paid for
shipping to the customer are non-refundable.
All customer shipping charges are non-fundable. Customers are responsible for any shipping charges incurred
for returns or exchanges. Customer will be billed for any additional shipping charges incurred for refused
shipments.
Prior to returning any products to Stryker T-Tops for a return or replacement, please fill out the form at
www.strykerttops.com/warranty-returns. If you are requesting to return multiple products, please complete a
form for each product. We will contact you via email within 2-3 business days with further instructions.
Contact Us
If you have any additional questions, please don’t hesitate to contact us. Our team is always available to help
you before your purchase, during the installation and for the lifetime of ownership.
Stryker T-Tops
23197 Alcalde Drive
Laguna Hills, CA 92653
(949) 407-5000
Table of contents
