Stryker SDC3 User manual

SDC3
HD Information Management System
HD INFORMA TION MANAGEMENT SYSTEM
SDC 3
0240060100


Table of Contents
Warnings and Cautions ............................................................................................1
About Your Product ...................................................................................................2
Product Description �����������������������������������������������������������������������������������������������������������2
Intended Use ������������������������������������������������������������������������������������������������������������������������2
Indications �����������������������������������������������������������������������������������������������������������������������������2
Contraindications ����������������������������������������������������������������������������������������������������������������2
System Overview .......................................................................................................3
Front Panel �����������������������������������������������������������������������������������������������������������������������������3
Rear Panel ������������������������������������������������������������������������������������������������������������������������������4
Basic Setup ����������������������������������������������������������������������������������������������������������������������������7
Getting Started ..........................................................................................................8
Powering the SDC3 On and O �������������������������������������������������������������������������������������8
Selecting a User Account �������������������������������������������������������������������������������������������������8
Logging In as the System Administrator ��������������������������������������������������������������������9
The Home Screen ������������������������������������������������������������������������������������������������������������� 10
Creating Patient Cases ........................................................................................... 11
Creating a New Patient Case ����������������������������������������������������������������������������������������11
Accessing a Current Patient Case ������������������������������������������������������������������������������� 11
Loading Patient Information ���������������������������������������������������������������������������������������� 12
Viewing the Patient List ��������������������������������������������������������������������������������������������13
Capturing Images and Videos .............................................................................. 14
Capturing Images and Video from a Single Channel ������������������������������������������14
Recording Picture-in-Picture Images and Video ���������������������������������������������������16
Synchronized Video Recording of Dual Channels ������������������������������������������������ 17
Independent Video Recording of Dual Channels �������������������������������������������������18
The Flip Screen ������������������������������������������������������������������������������������������������������������������19
Video Settings: Channel 1 ��������������������������������������������������������������������������������������������� 20
Video Settings: Channel 2 ��������������������������������������������������������������������������������������������� 21
Video Settings: Picture-in-Picture ������������������������������������������������������������������������������22
Picture-By-Picture ������������������������������������������������������������������������������������������������������ 23
Video Settings: On-Screen Display ���������������������������������������������������������������������������� 23
Printer Settings: Page Layout ���������������������������������������������������������������������������������������24
Printer Settings: Advanced �������������������������������������������������������������������������������������������25
Saving Images and Videos .................................................................................... 26
Selecting the Save Location �����������������������������������������������������������������������������������������27

Saving to a Network �������������������������������������������������������������������������������������������������28
Save Settings ��������������������������������������������������������������������������������������������������������������������� 29
Advanced Save Settings ������������������������������������������������������������������������������������������������30
Playback of Images and Videos ........................................................................... 31
Playback of Recorded Images ��������������������������������������������������������������������������������������32
Editing Image Annotations ������������������������������������������������������������������������������������� 33
Playback of Recorded Videos ���������������������������������������������������������������������������������������34
Editing Video Annotations �������������������������������������������������������������������������������������� 35
Printer Settings ����������������������������������������������������������������������������������������������������������������� 36
Viewing Archived Information ............................................................................. 37
Viewing Information Archived on the Hard Disk ��������������������������������������������������38
Viewing Information Archived on a USB Drive ������������������������������������������������������39
Viewing Information Archived on a Disc �����������������������������������������������������������������40
Viewing Information Archived on the Studio3 Media Server ��������������������������41
SDC3 Settings .......................................................................................................... 42
General Settings ���������������������������������������������������������������������������������������������������������������43
General Application Settings ���������������������������������������������������������������������������������44
General Miscellaneous Settings ����������������������������������������������������������������������������� 46
General Audio Settings ���������������������������������������������������������������������������������������������49
General Video Settings ��������������������������������������������������������������������������������������������� 50
Printer Settings ����������������������������������������������������������������������������������������������������������������� 51
Network Settings��������������������������������������������������������������������������������������������������������������52
Network FTP Settings ������������������������������������������������������������������������������������������������ 52
SDC3 Networking Setup ������������������������������������������������������������������������������������������53
Network Adapter Settings ���������������������������������������������������������������������������������������54
WiFi Network Connection ���������������������������������������������������������������������������������������� 55
Authentication ����������������������������������������������������������������������������������������������������������� 56
Wireless IP Settings ����������������������������������������������������������������������������������������������������57
Network Streaming Settings �����������������������������������������������������������������������������������58
User Account Settings ����������������������������������������������������������������������������������������������������59
Creating a New User �������������������������������������������������������������������������������������������������60
Modifying a Selected Account ��������������������������������������������������������������������������������61
System Settings ����������������������������������������������������������������������������������������������������������������67
Date and Time Settings ��������������������������������������������������������������������������������������������67
System Log Settings �������������������������������������������������������������������������������������������������� 68
System Language Settings ��������������������������������������������������������������������������������������69
Studio3 Server Settings �������������������������������������������������������������������������������������������������71
Selecting Fields for Cases Saved on the Studio3 Server ������������������������������������72
Studio3 Networking Setup ��������������������������������������������������������������������������������������72

Saving to a Network �������������������������������������������������������������������������������������������������28
Save Settings ��������������������������������������������������������������������������������������������������������������������� 29
Advanced Save Settings ������������������������������������������������������������������������������������������������30
Playback of Images and Videos ........................................................................... 31
Playback of Recorded Images ��������������������������������������������������������������������������������������32
Editing Image Annotations ������������������������������������������������������������������������������������� 33
Playback of Recorded Videos ���������������������������������������������������������������������������������������34
Editing Video Annotations �������������������������������������������������������������������������������������� 35
Printer Settings ����������������������������������������������������������������������������������������������������������������� 36
Viewing Archived Information ............................................................................. 37
Viewing Information Archived on the Hard Disk ��������������������������������������������������38
Viewing Information Archived on a USB Drive ������������������������������������������������������39
Viewing Information Archived on a Disc �����������������������������������������������������������������40
Viewing Information Archived on the Studio3 Media Server ��������������������������41
SDC3 Settings .......................................................................................................... 42
General Settings ���������������������������������������������������������������������������������������������������������������43
General Application Settings ���������������������������������������������������������������������������������44
General Miscellaneous Settings ����������������������������������������������������������������������������� 46
General Audio Settings ���������������������������������������������������������������������������������������������49
General Video Settings ��������������������������������������������������������������������������������������������� 50
Printer Settings ����������������������������������������������������������������������������������������������������������������� 51
Network Settings��������������������������������������������������������������������������������������������������������������52
Network FTP Settings ������������������������������������������������������������������������������������������������ 52
SDC3 Networking Setup ������������������������������������������������������������������������������������������53
Network Adapter Settings ���������������������������������������������������������������������������������������54
WiFi Network Connection ���������������������������������������������������������������������������������������� 55
Authentication ����������������������������������������������������������������������������������������������������������� 56
Wireless IP Settings ����������������������������������������������������������������������������������������������������57
Network Streaming Settings �����������������������������������������������������������������������������������58
User Account Settings ����������������������������������������������������������������������������������������������������59
Creating a New User �������������������������������������������������������������������������������������������������60
Modifying a Selected Account ��������������������������������������������������������������������������������61
System Settings ����������������������������������������������������������������������������������������������������������������67
Date and Time Settings ��������������������������������������������������������������������������������������������67
System Log Settings �������������������������������������������������������������������������������������������������� 68
System Language Settings ��������������������������������������������������������������������������������������69
Studio3 Server Settings �������������������������������������������������������������������������������������������������71
Selecting Fields for Cases Saved on the Studio3 Server ������������������������������������72
Studio3 Networking Setup ��������������������������������������������������������������������������������������72
Surgical Timeout Checklist Screens .................................................................... 73
Surgical Timeout Checklist Start Screen ������������������������������������������������������������������ 73
Surgical Timeout Checklist Verication Screen ����������������������������������������������������� 74
Surgical Timeout Checklist Summary Screen ��������������������������������������������������������75
Troubleshooting ..................................................................................................... 76
Electromagnetic Compatibility ............................................................................ 78
Cleaning and Maintenance ................................................................................... 81
Symbols .................................................................................................................... 82
Technical Specications ........................................................................................ 83


EN-1
Warnings and Cautions
Please read this manual and follow its instructions carefully� The words warning, caution, and note
carry special meanings and should be carefully reviewed:
Warning: Indicates risks to the safety of the patient or user� Failure to follow warnings may result
in injury to the patient or user��
Caution: Indicates risks to the equipment� Failure to follow cautions may result in product
damage�
Note: Provides special information to clarify instructions or present additional useful information�
1� Caution: Federal law (United States of America) restricts this device to use by, or on order of,
a physician�
2� Read this operating manual thoroughly and be familiar with its contents prior to setting up
or using this equipment�
3� Carefully unpack the unit and check for any damage that may have occurred during
shipment� If damage is detected, contact your Stryker representative�
4� Use of this device is restricted to qualied health care professionals who have a complete
knowledge of the use of this equipment and the devices to which it can be connected�
5� Test this equipment prior to using it in a surgical procedure� This unit was fully tested at the
factory before shipment; however, it must be tested for proper function in the environment
and setup conguration in which it will be used�
6� To avoid risk of electric shock, use only a hospital-grade power cord furnished with the
unit� Disconnect the unit from the power supply to make connections or to inspect the
equipment�
7� Install this device in an operating room that complies with all applicable IEC, CEC, and NEC
requirements for safety of electrical devices� Any installation or connection with other
devices shall be evaluated for electrical safety according to the IEC 60601-1:2005 +Corr 2006
+Corr 2007 standard�
8� Use only clean, dry, undamaged Stryker brand media� The use of damaged, wet, or
incompatible media will void the warranty and may result in the malfunctioning of this
equipment�
9� Ensure that all equipment connected to the SDC3 is properly grounded (and isolated, if
required)�
10� To avoid risk of re, do not use this device in the presence of ammable anesthetics�
11� Avoid direct exposure to the laser beam of the DVD/CD drive as it may harm the eyes�
12� Pay close attention to the care and cleaning instructions in this manual� Failure to follow
these instructions may result in product damage�
13� Attempt no internal repairs or adjustments not specically detailed in this operating manual�
Refer any adjustments, modications, and/or repairs to Stryker Endoscopy or its authorized
representatives�
14� This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment� This equipment should be installed and operated with minimum distance 20
cm between the radiator and your body�
The Stryker Standard Warranty and Return Policy (1000401175) is void if any of these warnings or
cautions are disregarded�

EN-2
About Your Product
Product Description
The SDC3 is a computer-based unit that records, manages, and archives digital images and videos
of surgical procedures� The SDC3 simplies le management by recording surgical photos and
videos to compact digital media, such as CDs, DVDs, Compact Flash Cards, USB Hard Drive, or
USB storage devices, which can then be viewed from a personal computer, a DVD player, or from
the SDC3 itself� The SDC3 records images and videos on a built-in hard drive, where they can be
easily accessed after the surgical procedure� The media stored on the hard drive can be tagged
with patient-specic information and burned to digital media using a touchscreen control panel
located on the front of the unit� This media can also be sent at the push of a button to the Studio3
Media Server for long-term storage and browser-based accessibility�
Intended Use
The SDC3 is intended to electronically capture, transfer, store and display medical device
data independently of the functions or parameters of any connected medical device� It is also
intended to convert medical device data from one format to another in accordance with preset
specications� The SDC3 is intended for use as a secondary display for regulated medical devices
and is not intended to calculate or modify any received data or provide primary diagnosis or
treatment decisions� It is not intended for use for active patient monitoring�
The SDC3 is a non-sterile reusable device not intended for use in the sterile eld� The SDC3 is
intended for use by qualied physicians and qualied operating room personnel who have
complete knowledge of surgical procedures�
Indications
The SDC3 is indicated for use with compatible endoscopic and general surgery devices� The SDC3
can be used in general laparoscopy, nasopharyngoscopy, ear endoscopy, sinuscopy, and plastic
surgery wherever a laparoscope/endoscope/arthroscope is indicated for use�
A few examples of the more common endoscopic surgeries are laparoscopic cholecystectomy,
laparoscopic hernia repair, laparoscopic appendectomy, laparoscopic pelvic lymph node
dissection, laparoscopically assisted hysterectomy, laparoscopic and thoracoscopic anterior spinal
fusion, anterior cruciate ligament reconstruction, knee arthroscopy, shoulder arthroscopy, small
joint arthroscopy, decompression xation, wedge resection, lung biopsy, pleural biopsy, dorsal
sympathectomy, pleurodesis, internal mammary artery dissection for coronary artery bypass,
coronary artery bypass grafting where endoscopic visualization is indicated, and examination of
the evacuated cardiac chamber during performance of valve replacement�
SDC3 users are general surgeons, gynecologists, cardiac surgeons, thoracic surgeons, plastic
surgeons, orthopedic surgeons, ENT surgeons, and urologists�
Contraindications
There are no known contraindications�

EN-3
System Overview
Front Panel
HD INFORMA TION MANAGEMENT SYSTEM
SDC 3
1� CD/DVD Drive
2� Eject button for CD/DVD Drive
3� USB Port
4� Token LED (for use with WiSe Receiver)
5� Token Slot (for use with WiSe Receiver)
6� Power Button
7� LCD Touchscreen
Notes:
• Digital Capture functions are not available on the SDC3 when controlled with the SIDNE
system.
• SDC3 les are not readable on the SDC UItra. SDC Ultra les can be read on SDC3.

EN-4
Rear Panel
1� SPI Preview – SPI Input (For future use)
2� Comp In – Composite Video Input
3� Comp Out – Composite Video Output
4� Equipotential Ground Plug – For connection to an external protective earthing system as
described in the IEC 60601-1 Electrical Safety standard
5� AC Power Inlet
6� Primary R1 – Remote connection for capture control on the primary channel
7� Primary R2 – Remote connection for recording control on the primary channel
8� S-Video IN1 – S-Video Input 1
9� S-Video IN2 – S-Video Input 2
10� S-Video Out – S-Video Output
11� Secondary R1 – Remote connection for capture control for secondary channel
12� Secondary R2 – Remote connection for recording control for secondary channel
13� DVI 2 Out – Secondary Channel DVI Output
14� DVI 2 In – Secondary Channel DVI Input
15� SFB Connector Ports – Enables Firewire connection with Stryker Firewire devices
16� eSATA – Compatible eSATA Cable Port (For future use)
17� DVI 1 Out – Primary Channel Output
18� Serial Port
19� DVI 1 In – Primary Channel Input
20� VGA
21� SORN – RJ45 SORN Port
22� USB Ports for mouse, keyboard, printer
23� RJ45 Port – Network Port
24� Devices – Stryker Devices Port
25� Line-In – Audio Input

EN-5
26� Line-Out – Audio Output
27� Headset – Audio In/Headset Out
Setup
Stryker Endoscopy considers instructional training an integral part of the SDC3 system� Your
Stryker Endoscopy sales representative will perform at least one in-service at your convenience
to help you set up your equipment and instruct you and your sta on its operation and
maintenance� Please contact your local Stryker Endoscopy representative to schedule an in-
service after your equipment has arrived�
1� Choose a location for the SDC3
• Place the SDC3 on a Stryker cart or other sturdy platform�
• Provide at least four to six inches of space around the sides and top of the SDC3 to
ensure proper ventilation and allow access to the power cord�
Warning
RF and other mobile communications equipment may aect the normal function
of the SDC3� When placing the SDC3, follow the instructions located in the
“Electromagnetic Compatibility” section of this manual�
2� Connect peripheral devices according to the interconnection diagram on the following
pages�
Warnings
• Connect only devices that have been specied as part of, or compatible with, the
SDC3 system�
• When the SDC3 is interconnected with other electrical devices, leakage currents
may be additive, resulting in electromagnetic emissions that can interfere
with the normal function of electronic medical equipment� To properly control
electromagnetic emissions and avoid potential harm to the patient or user,
ensure all electrical devices are installed and interconnected according to the
requirements of IEC 60601-1 and IEC 60601-1-1�
• When installed inside the patient environment, represented by an area 1�5
meters from the patient in all directions, the printer must be connected to an
isolation transformer prior to use� Recent Stryker carts include isolation

EN-6
transformers and printers can be installed without the use of an additional
transformer� Please contact your Stryker Endoscopy sales representative to
determine if your cart includes this feature�
3� Connect the AC power�
• Connect the provided hospital power cord to the AC inlet on the rear console panel�
• Connect the other end to a hospital-grade power outlet�
• Use a hospital power cord, part number 0105033001 or part number 0105150027�
Warning
• Check the power cord assembly periodically for damaged insulation or
connectors�
• To avoid risk of electric shock, this equipment must only be connected to a
supply mains with protective earth�
4� (Optional) Connect the equipotential ground probe to an equipotential bus bar (if available)�
The ground probe is provided to ensure all devices installed on the cart are connected to the
same ground potential� Ensure all connections are made according to the requirements of
IEC 60601-1�
5� (Optional) Connect the SDC3 to the WiSe Receiver�
• Insert the LED token provided with the WiSe receiver into the token slot on the front of
the SDC3 console according to the sequence of steps described in the WiSe receiver user
guide�
• When the LED light is o, no link is active, and the token can be inserted to begin
synchronization�
• When the LED light displays green, the link is active, and it is okay to remove the token�
• When the LED light displays amber, the system is busy and the token should not be
inserted or removed�
Note: The SDC3 can only be linked to one WiSe Receiver.

EN-7
Warning
In the event of power loss, all DVI output signals routed from the SDC3 to the surgical
display will be lost� Analog signals (RGBHV, S-Video, Composite) will not be aected
by power loss, and can therefore be used as backup video signals if they have been
connected prior to power loss�
Basic Setup
1� WiSe 26” Monitor 3� Printer
2� SDC3 4� 1288 Camera Control Unit

EN-8
Getting Started
Powering the SDC3 On and O
• To power on the SDC3 console, press the power button located at the bottom left corner of
the front panel� The button will shine green when the system is powered on�
• To power o the system, press the power button again and wait for the LED to turn o�
• As the system starts up, the SDC3 will display the Stryker logo, a black screen, then the
following screen� After a user is selected, the system will say, “Greetings� One moment please�
SDC Ready� Digital Capture Initializing�”
1� The version of the SDC3 software appears beneath the SDC3 logo�
2� Loading progress displays at the bottom of the screen�
Selecting a User Account
After startup, the User Accounts screen will appear if there are multiple user accounts saved in the
SDC3 system�

EN-9
1� Select the desired user account by touching the corresponding icon�
2� Markers at the bottom of each screen show the current screen and total number of screens�
3� To view additional user account screens, touch the button�
Logging In as the System Administrator
The System Administrator account can be accessed from the User Accounts Screen�
• If the account is not password protected, the SDC3 will proceed to the Home Screen�
• If the account is password protected, the login screen will appear:
3
2
1
1� Enter the account password in password eld�
2� After password is entered, press the LOGIN button� After successful login, the system will
display the Home screen�
3� To return to the User Accounts screen, press the SWITCH USER button�

EN-10
The Home Screen
After selecting a user account or logging in as the system administrator, the Home Screen is
displayed� The Home Screen provides links to the major functions of the SDC3� From the Home
Screen, you can
• start a new patient case
• access current patient cases
• access archived patient information
• load patient information into the system
• adjust system settings
1 65432
1� Pressing the SETTINGS button will navigate to the SDC3 Settings screens�
2� Pressing the NEW CASE button will begin a new patient case�
• If a patient case has already been started, but there is no data saved to that case,
the system will conrm, “Do you wish to discard the current case?”
• If a patient case has already been started, and there is data saved to that case, the
system will conrm, “Do you wish to create a new case?”
• Pressing will navigate back to the Home screen� Pressing will navigate
to the New Case screen�
3� Pressing the CURRENT CASE button will navigate to the Current Case screen�
4� Pressing the ARCHIVE button will navigate to the Archived Cases screen, which displays
cases that have been saved to the SDC3, a USB storage device, a disc, or the Studio3 media
server�
5� Pressing the LOAD PATIENT INFO button will navigate to the Patient Info screen to
preload patient information before surgery�
6� Pressing the LOG OFF button will log o the current user� The Login screen will reappear�

EN-11
Creating Patient Cases
The SDC3 organizes all the data associated with a patient into a patient “case�” Patient cases
include information about the patient, the procedure, and any pictures or video captured during
the procedure� Patient cases can be created, accessed, modied, and saved to the SDC3 hard disk
or to external media, such as USB drives, CD/DVD, or network servers�
Creating a New Patient Case
To create a new patient case:
1� On the Home screen, press the NEW CASE button�
2� From the conrmation screen, press to conrm the new case and proceed to the
Capture Screen�
Note: If a patient case has already been started, the SDC3 will ask if you want to discard that
case (the “current case”) before creating a new case. Discarding the case will erase any data
associated with that case. If you do not wish to discard the current case, you can access it
through the CURRENT CASE button from the Home screen.
Accessing a Current Patient Case
To access a current patient case (one for which patient data, pictures, or video has already been
saved to the SDC3):
1� On the Home screen, press the CURRENT CASE button� The Capture Screen will appear�
2� On the Capture Screen, select the desired patient case from the CURRENT CASE PATIENT
ID dropdown list�

EN-12
Loading Patient Information
Patient information (name, ID, procedure, etc�) can be pre-loaded into the system so it will be
available when creating new patient cases� The patient information entered and saved in the
Load Patient Info screen becomes available as a Current Case in the dropdown menu on the
Capture screen�
2
4
3
To load patient information into the SDC3:
1� On the Home Screen, press the LOAD PATIENT INFO button� The Load Patient Info
screen will appear�
2� Populate the desired data elds�
• Touch the desired eld to open a keyboard for typing in data, or
• Select a value from the dropdown list�
• At a minimum, the Patient ID eld should be populated� All other elds are optional�
3� Press the ADD PATIENT button to save the patient information and add the patient to
the current case list�
4� To view patients currently loaded into the system, press the VIEW PATIENT LIST tab�

EN-13
Viewing the Patient List
The Patient List screen displays patient cases that have already been loaded into the system�
1
2
3 4
5
1� To select a case for editing or deletion, touch the corresponding row�
2� To view or edit the selected case, press the OK button�
3� To delete the selected case, press DELETE button�
4� To delete all cases, press the DELETE ALL button�
5� To return to the Load Patient Info screen, press the button�

EN-14
Capturing Images and Videos
Within a patient case, image and video les can be captured to document a surgical procedure�
To open the Capture screen for a patient case, select a NEW CASE or CURRENT CASE
from the Home screen�
Capturing Images and Video from a Single Channel
The Capture screen displays the live image from the camera� The live image can be recorded
as video or captured as a still image�
Note: At least one video source (channel) must be connected to the SDC3 to enable video
recording and image capture.
9
87 65
4
3
1 2
To record video:
1� Press RECORD to initiate recording�
Press PAUSE to pause recording� Video recording duration, video source signal, and video
size are displayed above the preview screen�
2� Press STOP to stop recording�
Other manuals for SDC3
1
This manual suits for next models
1
Table of contents
Other Stryker Measuring Instrument manuals