Studebaker SB3705 User manual

E-1

E-2
COMPLIANCE WITH FCC REGULATIONS
FCC ID: 2AWRTSB-3705
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) Thisdevicemaynotcauseharmfulinterference,and
(2) This device must accept any interference received, including interference that may
causeundesiredoperation.
This equipment has been tested and found tocomply with the limits for a Class B Digital
Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of thefollowingmeasures:
- Reorient or relocate thereceivingantenna.
- Increase the separation between the equipmentandreceiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
isconnected.
- Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible
forcompliancecouldvoidtheuser'sauthoritytooperatetheequipment.
CAUTION
Followtheadvicebelowforsafeoperations.
ON PROTECTION AGAINST LASER ENERGY EXPOSURE
Asthelaserbeamusedinthiscompactdiscplayerisharmfultotheeyes,donotattemptto
disassemblethecasing.
Stopoperationimmediatelyifanyliquidorsolidobjectshouldfallintothecabinet.
Donottouchthelensorpokeatit.Ifyoudo,youmaydamagethelensandtheplayermay
notoperateproperly.
Do not put anything in the safety slot. If you do, the laser diode will be ON when the CD
door isstillopen.
If the unit is not to be used for a long period of time, make sure that all power sources are
disconnectedfromtheunit.Removeallbatteriesfromthebatterycompartment.
This unit employs a laser. The use of controls or adjustment or performance of procedures
otherthanthosespecifiedheremayresultinexposuretohazardousradiation.
Shouldanytroubleoccur,removethepowersourceandreferservicingtoqualifiedpersonnel.

E-3
DEAR STUDEBAKER CUSTOMER
Selecting fine audio equipment such as the unit you've just purchased is only the start of your
musical enjoyment. Now it's time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association's
Consumer Electronics Group want you to get the most out of your equipment by playing it at
a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion and, most importantly, without affecting your sensitive hearing. Sound can be
deceiving.Overtimeyourhearing"comfortlevel"adaptstohighervolumesofsound.Sowhat sounds
"normal" can actually be loud and harmful to your hearing. Guard against this by
settingyourequipmentatasafelevel BEFOREyourhearingadapts.
To establish a safe level:
• Start your volume control at a lowsetting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
• Once you have established a comfortable sound level: Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for alifetime.
WeWantYouListeningForaLifetime
Used wisely, your new sound equipment will provide a lifetime of
fun and enjoyment. Since hearing damage from loud noise is
often undetectable until it is too late, this manufacturer and the
Electronic Industries Association's Consumer Electronics Group
recommend you avoid prolonged exposure to excessivenoise.
Customer'sRecord:
The serial number of this product is found on its bottom cover. You should note the serial
number of this unit in the space provided as a permanent record of your purchase to aid in
identification in the event of theft ofloss.
ModelNumber:SB3705 SerialNumber:

E-4
LOCATION OF CONTROLS
7
8 14
9 15
10 16
11 17
12 18
13 19
1
CD DOOR OPEN SWITCH
11
MODE BUTTON
2
MICRO USB JACK
12
BBS ON/OFF BUTTON
3
DC IN JACK
13
10 + BUTTON
4
HOLD OFF/ON SWITCH
14
/ OFF BUTTON
5
STEREO EARPHONE JACK
15
/ ON BUTTON
6
VOLUME CONTROL
16
M + BUTTON
7
LCD DISPLAY
17
M - BUTTON
8
TUNER / BUTTON
18
PROG / MEM BUTTON
9
TUNER / BUTTON
19
FM BUTTON
10
CD BUTTON
5V
1
2 3
4
5 6

E-5
POWER SOURCE
BATTERY OPERATION
Notes: If you are using an external AC adapter (not included) for powering the unit,
disconnect it beforeinstalling batteries.
Forbestperformanceandlongeroperatingtime,werecommendtheuseofalkalinebatteries.
1. Open the BATTERY DOOR on the bottom ofthe unit.
2. Follow the polarity diagram shown in the BATTERY COMPARTMENT to insert 2 X ‘AA’
size(UM-3)batteriesandclosetheBATTERYDOOR.
3. The LCD backlight last for 30 seconds when you press the buttons if you are using battery
powered.
BATTERYWARNING
1. Besurethebatteriesareinstalledcorrectly.Wrongpolaritymaydamagetheunit.
2. Useonlythesizeandtypeofbatteriesspecified.
3. Do not mix old andnew batteries.
4. Donotmixalkaline,standard(carbon-zinc)orrechargeable(nickel-cadmium)batteries.
5. If the unit is not to be used for an extended period of time, remove the batteries. Old or
leakingbatteriescancausedamagetotheunitandmayvoidthewarranty.
6. Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow batterymanufacturer’sdirections).
7. Donotdisposeofbatteriesinfire,batteriesmayleakorexplode.
ACADAPTOROPERATION(adaptornotincluded)
ThisunitcanalsobepoweredusinganACadapter(notincluded)withaninputvoltageofAC
120V~60Hz,andoutputvoltageofDC4.5V 700mA .
1. PlugtheACadaptor(notincluded)intonormalACpoweroutletsocket.
2. Insert the DC plug of the AC adaptor cord into the DC INJACK(#3).
3. When the unit is operated using AC adapter, the battery source will automatically be
disconnected.
WARNING: Before connecting to the power supply, ensure that the supply corresponds to
theinformationontheratinglabelatthebackoftheapparatus
USB POWER
This unit can also be powered using the built-in MICROUSBJACK (#2) and a USB power source
(not included) like a cell phone charger, computer USB port or USB power bank. USB cord is
also required.
1. Use a USB power source with a minimum output of DC 5V 700mA.
2. Plug one end (micro USB plug) of the USB cable into the MICRO USBJACK (#2) and the
other end of the cable to the USB charger/power bank/computer (not included).
3. The battery source will automatically be disconnected when using the USB port for
powering the unit
Caution: When not using USB power, disconnect the USB cable.

E-6
EARPHONES CONNECTION
Connect the plug of the stereo earbuds (included) into the STEREO EARPHONE JACK (#5).
Notes:
•Without insert the earphones, the unit will enter CD and FM transmit mode.
•When earphones is inserted, the FM transmission is stop. Press CD MODE BUTTON (#10)
to select CD mode. Press FM MODE BUTTON (#19) to select FM radio mode..
CAUTION
•Avoid excessive volume levels for long period of time when using the
earphones.Prolonged use at high levels may impairyour hearing.
•Do not use earphones while operating a motorized vehicle, as it may create a
traffichazard and is illegal inmany areas.
CD / MP3 CD OPERATION
PLEASE READ THIS IMPORTANT INFORMATION:
CD mechanisms used in devices like this are designed to fully read all commercial CDs. They
willalsoreadself-compiledCD-R/CD-RWdiscsbutitmaytakeupto10secondsforplayback to start. If
playback does not start, it is likely due to the quality of the CD-R/RW disc and/or the
compatibility of the CD compilation software. Manufacturer is not responsible for the
playbackqualityofCD-R/RWdiscs.
DonotattachalabelorsealtoeithersideoftheCD-R/RWdisc.Itmaycauseamalfunction.
FOR WINDOWS USERS:
When using the “Burn a CD” feature to create an MP3 CD in Windows, you must select the
“With a CD/DVD player”option when it asks “How do you want to use the disc?” The MP3 CD
will not play on this unit if you select the “Like aUSB flash drive” option or if the MP3 CD is not
finalized
1. Press / ON BUTTON to turn on the unit.
2. Press CD BUTTON to enter CD mode if necessary.
(For power saving, the unit will turn off automatically after idled 60 seconds.)
3. SlidetheCD DOOROPEN SWITCH(#1)toopentheCDdoor.
4. CarefullyplaceanaudioCD/MP3CDwithitslabelsideupwardintheCDcompartment and close
the CDdoor.
5. The player will start reading TOC ofthedisc.
6. The total number of tracks and time on the CD will appear on the LCD DISPLAY (#7)
after a fewseconds
Note: The total number of folders and tracks on the MP3 CD will appear on the LCD
DISPLAY (#7).
7. Tapthe / ON BUTTON(#15)to start toplay.
8. Adjust the VOLUME CONTROL (#6) to obtain the desired sound level.
9. To suspend playing, tap the / ON BUTTON(#15) again. To resume playing, tap the
/ ON BUTTON(#15) again.
10. You can choose to play your favorite track directly by pressing either the /
BUTTON or / BUTTONS (#8 or #9) repeatedly. The LCD Display (#7) will indicate
the correct track number selected.
Tap the 10+ BUTTON to select the next 10 tracks
11. To locate a particular passage within a track, keep the / BUTTON or /

E-7
BUTTONS (#8 or #9) depressed until it is found.
12. To repeat a particular track, tap the MODE BUTTON (#11) repeatedly until the “”
indicator lights on the LCD DISPLAY.
Note: To repeat the entire folder of the MP3 CD, tap the MODE BUTTON (#11)
repeatedly until the “DIR” indicator lights on the LCD DISPLAY (# 7).
13. To repeat all the songs on the disc, tap the MODE BUTTON (#11) repeatedly until the
“ALL” indicator light on the LCD display.
14. To play the first 10 seconds of each song on the disc, tap the MODE BUTTON (#11)
repeatedly until the “INTRO” indicator light on the LCD display.
15. To play songs randomly,tap the MODE BUTTON (#11) repeatedly until the RAND
indicator light on the LCD display.
16. To stop playing, tap the / OFF BUTTON (#14).
17. Press and hold the /OFF BUTTON (#14) to turn off the unit
PROGRAM OPERATION
This function allows the tracks to be played in a programmed sequence.
Programs can be set in STOP mode.
1. Tap the PROG / MEM BUTTON (#18) once. The Program Channel Number "01P" will
appear and the “PROG” indicator and track number “00” will blink on the LCD DISPLAY
(#7) to prompt for input.
[For MP3 CD, track number “000” will blink on the LCD DISPLAY (#7) to prompt for input.]
2. Tap / BUTTON or / BUTTON (#8 or #9) repeatedly t select the track to be
programmed.
3. Tap the PROG/MEMbutton (#18) again to store selection. The Program Channel
numberwillchangeto02Pandthetracknumberwillreturnto00 (000 for MP3
CD)topromptforinput.
4. You mayrepeatsteps2-3toprogramas manyas20tracks.
5. Tap BUTTON (#15) tostart theprogrammedplay, the “PROG”indicator will show up in
the LCD DISPLAY (#7).
6. You may repeat the current programmed track or all programmed tracks by pressing the
MODEbutton(#11)repeatedlyto select repeat 1 or repeat all at programmed play mode.
7. Tap /OFFBUTTON (#14) once to stop playback.
8. Tap / ON BUTTON (#15) to resume programmed play.
9. To cancel programmed play, press /OFFBUTTON (#14) twice.
ANTI-SHOCK PROTECTION
This player incorporates an electronic anti-skip circuit to prevent interruption of the sound
outputwhentheunitissubjectingtoshock,vibrationorrollingduringCDplayback.Theantis- shock
system will automatically activate when a discisplayed.
Once anti-skip buffer is full, it will give you approximately 60 seconds (CD disc) or 120
seconds (MP3 disc) of protection against interruption of sound output. If the player is
subjected to shock or rolling for longer than the buffer memory, some interruption of sound
output will occur. This is normal and to be expected and the sound will resume once the
player has stabilized from the shock or rolling disturbance.
Note: The anti-skip function provides for continues sound output when the unit is subjected
to shock or vibration. It will not compensate for errors arising from the use of defective,
scratched or dirtydiscs.

E-8
RADIO OPERATION
1. Press / ON BUTTON to turn on the unit.
2. Press FM MODE BUTTON(#19) to selectFMmode.
3. The “FM”indicatorandradiofrequencylightontheLCDDISPLAY(#7).
4. To manually tune to a specific radio station, tap / BUTTON or / BUTTON (#8 or
#9). Use the manual tuning method to tune in weaker stations that
arebypassedduringAutomaticTuning.
5. To automatically tune to the next available radio station, press and hold the / BUTTON
or / BUTTON (#8 or #9) 1-2 seconds until frequencyreadoutonthedisplay begins to scan
and then release the button. The tuner will stop scanning when it
receivesthenextbroadcastingstationofadequatesignalstrength.
6. Adjust the VOLUME CONTROL (#6) to the desiredvolumelevel.
PRESET RADIOSTATIONS
1. Tunetothedesiredradiostationeitherby“manually”or“automatically”tuningmethod.
2. After receiving a station, press and hold the PROG/MEM BUTTON (#18), the “MEM’
indicator and the preset memory number P-01 will blinkon the LCD DISPLAY (#7) to prompt
for input, press the M + BUTTON (#16) or M – BUTTON (#17) repeatedly to select the preset
numberyou want to assign the station to.
3. Tap the PROG/MEM BUTTON (#18) to confirm the setting.
4. Repeat above steps 1 - 3 to preset up to 20stations.
TIPSFORBESTRECEPTION
•Thecordoftheearphoneactsasanantennafortheradioandmustbefullyextendedfor
bestreception.
•Unplug the earphone, the unit will change to CD mode automatically.
FM TRANSMISSION
1. Press / ON BUTTON to turn on the unit.
2. Disconnect the earphones if necessary. The unit will enter CD and FM transmit mode
automatically.
3. Adjust the radio (car radio) to the white space (i.e. the channel without any broadcast).
The reference is clear rustling.
4. Press M+ BUTTON (#16)/ M- BUTTON(#17) to adjust the transmission frequency (87.5-
108MHz) to the same as the radio (car radio).
(The transmit frequency will show on the LCD display (#7) and last 2 seconds,
5. Now you can enjoy the CD/CDMP3 music from the SB3705 through your radio (car radio).
Notes:
•The transmit frequency of the factory preset is 88.1 MHz. For quick connect with your
radio (car radio), just play CD without insert the earphones. Radio (car radio) search
down to find the transmit frequency (88.1 MHz) would be OK.
•Once earphones inserted, the unit will stop the transmission.

E-9
BASSBOOSTFUNCTION
Tapthe BBS ON/OFF BUTTON (#12) to turn on the BBS to enhance the bass effect of the
music. Tap again to turn off the BBS.
HOLDFUNCTION
To prevent accidental function changes during active use, this unit is fitted with a function
hold. After the unit has been powered on and playing in CD or FM mode,slide the HOLD
ON/OFF SWITCH (#4) to ON position.The hold indicatorwill lightontheLCDDISPLAY(#7).
Slide the HOLD ON/OFF SWITCH (#4) to OFF position toturnoffthehold function.
RESETTING THE UNIT
In case of malfunction due to electrostatic discharge, reset the unit by disconnecting the DC
plug of the AC Adapter from the DC IN JACK (#3) and remove the batteries. Wait at least
for3minutesbeforereconnectingtheDCplugtotheDCINJACK(#3)orinsertthebatteries.
INSTALLING CAR MOUNT
Attach the magnetic mount to air vent by sliding the vent claw onto a single air vent flap.
There is one metal plate installed inside the unit. Place your unit on the magnetic car mount.
CAREANDMAINTENANCE
1. Cleanyourunitwithadamp(neverwet)cloth.Solventordetergentshouldneverbeused.
2. Avoidleavingyourunitindirectsunlightorinhot,humidordustyplaces.
3. Keep your unit away from heating appliances and sources of
electrical noise such as fluorescent lampsor motors.
4. If drop-outs or interruptions occur in the music during CD play,
or if the CD fails to play at all, its bottom surface may require
cleaning. Before playing, wipe the disc from the center outwards
with a good soft cleaningcloth.

E-
TROUBLESHOOTINGGUIDE
If you experience difficulties in the use of this CD / MP3 CD Player, please check the
following or call 1-800-777-5331 for Customer Serviceand support
SYMPTOM
POSSIBLE
SOLUTION
Nosound
Battery nopower
Replace all batteries with new
ones.
Volume set atminimum
IncreaseVolume.
Noise or sound
distorted on FM
broadcast
Earphone cord is not
extended Extend earphonecord
Radio nosound
The
mode
unit
is
not
in
Radio
Insert the earphone and select
Radiomode
The station isweak
Retune the stationagain
CD player will notplay
Unit not in CDmode
Switch to CDmode
CD is installedincorrectly
Insert CD with label sideup.
Batteries becomeexhausted
Replace all batteries with new
ones.
It the CD is self-compiled, the
media used may not be
compatible with theplayer.
Use better quality blank media
andretest.
CD skips whileplaying
Disc is dirty orscratched.
Wipe CD with clean cloth oruse
anotherdisc.
Dirty or defectivedisc
Clean or replace the defective
disc
Dirty pick uplens
Use a CD-lens cleaning disc to
clean thelens
Player is subject to excessive
shock orvibration
Relocate the player away from
shock orvibration
Batteries becomeexhausted
Replace all batteries with new
ones.
SPECIFICATION
Power Requirement Battery: 2 x "AA"(UM-3) batteries(notincluded)
AC Adaptor (not included): Input: AC 120V ~60Hz
Output:DC4.5V 700mA
USB Power Output: DC 5V 500mA
FMFrequency 87.5 MHz– 108MHz
TM Transmission 87.5 MHz– 108MHz

E-
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U.S.A. ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from defective
materials or factory workmanship for a period of 90 days from the date of original customer
purchase and provided the product is utilized within the U.S.A. This warranty is not assignable
or transferable. Our obligation under this warranty is the repair or replacement of the defective
unit or any part thereof, except batteries, when it is returned to the SPECTRA Service
Department, accompanied by proof of the date of original consumer purchase, such as a duplicate
copy of a sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty service. If
the product is repaired or replaced under warranty, the return charges will be at SPECTRA’s
expense. There are no other express warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage
outside the descriptions and warnings covered within the user manual or non-
SPECTRA approved modifications.
c. Claims are made within the warranty period.
2. This warranty does not cover damage or equipment failure caused by electrical wiring not in
compliance with electrical codes or SPECTRA user manual specifications, or failure
to provide reasonable care and necessary maintenance as outlined in the user manual.
3. Warranty of all SPECTRA products applies to residential use only and is void when
products are used in nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. TO OBTAIN SERVICE please remove all batteries (if any) andpack the unit carefully
and send it freight prepaid to SPECTRA at the address shown below. IF THE UNIT IS RETURNED
WITHIN THE WARRANTY PERIOD shown above, please include a proof of purchase (dated
cash register receipt) so that we may establish your eligibility for warranty service and repair of the
unit without cost. Also include a note with a description explaining how the unit is defective. A
customer service representative may need to contact you regarding the status of your repair, so
please include your name, address, phone number and email address to expedite the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $30.00 to cover
the cost of repair, handling and return postage. All out of warranty returns must be sent prepaid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at
[e-mail] for updated information on the unit requiring service. In some cases,
the model you have may be discontinued, and SPECTRA reserves the right to offer alternative
options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL60634, USA. 1-800-777-5331
To register your product, visit the link on the website below to enter your information.
http://www.spectraintl.com/wform.htm
0720 Printed in China