TECHWOOD DVDC97 User manual

2
Safety Precautions
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference, should the unit
require maintenance, contact an authorized service location-
see service procedure.
Use of controls, adjustments or the performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to water,
dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifi-
cations are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Notes on copyrights:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyright material without
permission.
This product is equipped with copy protection measures
developed by Macrovision. Copy protection signals are record-
ed on some discs. When recording these discs on a VCR,
picture noise will appear during playback.
This product incorporates copyright protection technology that
is protected by certain U.S. patent claims and other intellectual
property rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: TO REDUCE THE RISK OF FIRE OR ELEC-
TRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

INTRODUCTION
3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS IN THIS OWNER’S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR
FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety.
Improper use can result in electric shock or fire hazard. The safeguards
incorporated in this unit will protect you if you observe the following proce-
dures for installation, use, and servicing.
This unit does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read These Instructions
All safety and operating instructions should be read before the
product is operated.
2. Follow All Instructions
All operating and use instructions should be followed.
3. Keep These Instructions
The safety and operating instructions should be retained for future
reference.
4. Heed All Warnings
All warnings on the product and in the operating instructions should
be adhered to.
5. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power supply in your home, consult your product dealer or
local power company. For products intended to operate from bat-
tery power, or other sources, refer to the operating instructions.
6. Grounding or Polarization
Do not defeat the safety purpose of the polarized plug has two
blades with one wider than the other. A grounding-type plug has
two blades and a third grounding prong. The wide blade or the
prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obso-
lete outlet.
7. Ventilation
Slots and openings in the cabinet are provided for ventilation and to
ensure reliable operation of the product and to protect it from over-
heating. These openings must not be blocked or covered. The open-
ings should never be blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventila-
tion is provided or the manufacturer’s instructions have been adhered
to.
8. Heat
Do not install near any heat sources such as radiators, heat regis-
ters, stoves, or other apparatus (including amplifiers) that produce
heat.
9. Water and Moisture
Do not use this apparatus near water. For example: near a bath
tub, wash bowl, kitchen sink, Laundry tub, in a wet basement; or
near a swimming pool.
10. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Clean only with dry cloth.
11. Power-Cord Protection
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
12. Overloading
Do not overload wall outlets, extension cords, or integral conven-
ience receptacles, this can result in a risk of fire or electric shock.
13. Lightning
Unplug this apparatus apparatus during lightning storms or when
unused for long periods of time. This will prevent damage to the
product due to lightning and power-line surges.
14. Object and Liquid Entry
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
15. Attachments
Only use attachments/accessories specified by the manufacturer.
16. Accessories
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
17. Disc Tray
Keep your fingers well clear of the disc tray as it is closing. It can
cause personal injury.
18. Burden
Do not place a heavy object on or step on the product. The object
may fall, causing serious personal injury and serious damage to the
product.
19. Connecting
When you connect the product to other equipment, turn off the
power and unplug all of the equipment from the wall outlet. Failure
to do so may cause an electric shock and serious personal injury.
Read the owner’s manual of the other equipment carefully and fol-
low the instructions when making any connections.
20. Sound Volume
Reduce the volume to the minimum level before you turn on the
product. Otherwise, sudden high volume sound may cause hearing
or speaker damage.
21. Sound Distortion
Do not allow the product to output distorted sound for a longtime. It
may cause speaker overheating and fire.
22. Earphone
When you use the earphone, keep the volume at a moderate level.
If you use the earphone continuously with high volume sound, it
may cause hearing damage.
23. Laser Beam
Do not look into the opening of the disc tray or ventilation opening
of the product to see the source of the laser beam. It may cause
sight damage.
24. Disc
Do not use a cracked, deformed, or repaired disc. These discs are
easily broken and may cause serious personal injury and product
malfunction.
25. Damage Requiring Service
Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normal, or has been dropped.
26. Servicing
Do not attempt to service this product yourself as opening or
removing the cover may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
27. Replacement parts
When replacement parts are required, be sure the service techni-
cian has used replacement parts specified by the manufacturer or
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
28. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
PORTABLE CART
WARNING

4
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel and Display Window . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to Optional Equipment . . . . . . . . . . . 11
Before Operation . . . . . . . . . . . . . . . . . . . . . . . 12-15
General Explanation. . . . . . . . . . . . . . . . . . . . . . 12
On-Screen Display. . . . . . . . . . . . . . . . . . . . . . . 12
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 13-15
 Initial Settings General Operation. . . . . . . . . 13
 Language . . . . . . . . . . . . . . . . . . . . . . . . . . 13
 Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
 Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
 Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
 Parental Control. . . . . . . . . . . . . . . . . . . . . . 15
Operation
Operation with DVD and Audio CD . . . . . . . . . 16-19
Playing a DVD and Audio CD. . . . . . . . . . . . . . . 16
 Exchanging discs during playback . . . . . . . . 16
 Skipping discs . . . . . . . . . . . . . . . . . . . . . . . 16
 Exchanging the disc and starting playback. . 16
General Features. . . . . . . . . . . . . . . . . . . . . . . . 17
 Moving to another TITLE . . . . . . . . . . . . . . . 17
 Moving to another CHAPTER/TRACK . . . . . 17
 Still Picture and Frame-by-Frame Playback . 17
 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
 Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 17
 Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
 Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
 Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
 Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 18
 Time Search . . . . . . . . . . . . . . . . . . . . . . . . 18
 Selecting the sound enhancement . . . . . . . 18
 Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
 Marker Search. . . . . . . . . . . . . . . . . . . . . . . 19
Special DVD Features . . . . . . . . . . . . . . . . . . . . 19
 Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
 Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
 Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 19
 Changing the Audio Language . . . . . . . . . . . 19
 Changing the Audio Channel . . . . . . . . . . . . 19
 Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Programmed Playback with Audio CD . . . . . . . . . 20
Programmed Playback with Audio CD . . . . . . . . 20
 Repeat Programmed Tracks/All . . . . . . . . . . 20
 Erasing a Track from Program List . . . . . . . . 20
 Erasing the Complete Program List . . . . . . . 20
Operation with MP3 Disc. . . . . . . . . . . . . . . . . . . . 21
Playing an MP3 Disc . . . . . . . . . . . . . . . . . . . . . 21
 Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
 Moving to another Track . . . . . . . . . . . . . . . 21
 Repeat Track/All/Off. . . . . . . . . . . . . . . . . . . 21
Notes on MP3 Discs . . . . . . . . . . . . . . . . . . . . . 21
Programmed Playback with MP3 Disc . . . . . . . . . 22
Programmed Playback with MP3 Disc . . . . . . . . 22
 Repeat Programmed Tracks/All . . . . . . . . . . 22
 Erasing a Track from Program List . . . . . . . . 22
 Erasing the Complete Program List . . . . . . . 22
Additional Information . . . . . . . . . . . . . . . . . . . . . 23
Last Condition Memory . . . . . . . . . . . . . . . . . . . 23
Screen Saver. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 23
Reference
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 25
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 26
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.

5
INTRODUCTION
Before Use
Playable Discs
DVD Video
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
Notes
– Depending on the conditions of the recording equip-
ment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on this unit.
– This unit cannot play CD-R/RW discs that do not con-
tain any data, or contain different kinds of formatted
data other than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heart-
shaped or octagonal). It may result in malfunctions.
Notes on DVDs
Some playback operations of DVDs may be intentional-
ly fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the soft-
ware manufacturer, some playback features of the unit
may not be available, or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
playable on this unit.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured
for playback of region “1” encoded DVD soft-
ware. The region code on the labels of some DVD discs
indicates which type of player can play those discs. This
unit can play only DVD discs labeled “1” or “ALL”. If you
try to play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their
playback is prohibited by area limits.
Note on DTS-encoded CDs
To avoid possible damage to the audio system, turn
down the volume before playing back such discs. Adjust
the volume gradually to personal preference. To enjoy
DTS Digital SurroundTM playback, an external 5.1 chan-
nel DTS Digital SurroundTM decoder system must be
connected to the digital output of the player.
Disc-related terms
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles.
A title is composed of one or several chapters. Each
chapter is assigned a chapter number, enabling you to
locate the chapter you want. Chapter numbers may not
be recorded on all discs.
Track (Audio CD only)
Sections of a picture or a musical piece on an audio
CD. Each track is assigned a track number, enabling
you to locate the track you want.
1

6
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, and turn off
the unit after removing the disc.
To keep the exterior surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not allow rubber or plastic products to
contact the unit for a long period of time. They will leave
marks on the surface.
To move the unit
When you move the player, take out any discs. If you
don’t, the discs may be damaged or drop into the inter-
nal workings of the DVD player.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents, such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn down, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sun-
light, as there may be a considerable temperature build-
up inside the car.
Cleaning discs
Fingerprints and dust on the disc can cause poor pic-
ture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the cen-
ter out.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
About Symbols
About the symbol display
“ ” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
When a section in this manual includes the following
icons, the data provided herein is applicable only to the
software represented by that icon.
DVD
Audio CDs.
MP3 disc.
MP3
CD
DVD

7
INTRODUCTION
Front Panel and Display Window
TITLE PROG. RANDOM ALL AB CHP/TRK
1
234 5
MP3 CD DVD
Forward Skip ( TT)
Advances to NEXT chapter/track.
Press and hold for two seconds for fast forward search.
DISC EXCHANGE
Changes a disc (other than the one playing) during playback
Reverse Skip ( SS)
Returns to beginning of current chapter/track or
to PREVIOUS chapter/track.
Press and hold for two seconds for fast reverse search.
STOP ( 99)
Stops playback.
PAUSE ( ;;)
Pauses playback temporarily /
press repeatedly for frame-by-frame playback.
PLAY ( 22)
Starts playback.
OPEN/CLOSE ( //)
Opens or closes the disc tray.
STANDBY/ON indicator
Lights red when the player is in Standby mode (off).
Remote Sensor
Point the DVD Player remote
control here.
Display window
Shows the current status of the player.
Indicates current player function:
Playback, Pause, etc.
A light will appear if a disc is in the disc
tray. The current disc tray flashes.
ANGLE Lights when multi angles
are present.
DVD inserted
CD Audio CD inserted
MP3 MP3 disc inserted
DVD
TITLE Indicates current title number
CHP/TRK Indicates current chapter or track number
Indicates total playing time/elapsed time
PROG. Programmed playback active
RANDOM RANDOM play-
back active
Indicates repeat
mode
Disc Tray
Insert a disc here.
POWER
Switches the player ON and OFF.
Disc number (1 - 5)
Selects a disc tray for playback.
DISC SKIP
Moves to the next available disc tray.

8
Remote Control
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor
Angle: About 30° in each direction of the front of the
remote sensor
Remote control battery installation
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with and
aligned correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
AAA
MARKER
Marks any point during playback.
POWER
Switches DVD Player ON and OFF.
AUDIO •
Selects an audio language (DVD) or
an audio channel (CD).
SUBTITLE •
Selects a subtitle language.
ANGLE •
Selects a DVD camera angle if
available.
RANDOM •
Plays tracks in random order.
ZOOM •
Enlarges video image.
STOP ( 99) •
Stops playback.
PAUSE/STEP ( ;;) •
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
GUI DISPLAY
Accesses On-Screen display
Reverse SLOW ( ,, ) •
Reverse slow playback.
Forward SLOW ( .. ) •
Forward slow playback.
MENU •
Accesses menu on a DVD disc.
TITLE •
Displays the discs Title menu, if
available.
SETUP •
Accesses or removes setup menu.
RETURN •
Removes the setup menu.
SEARCH
Displays MARKER SEARCH menu.
OPEN/CLOSE
Opens and closes the disc tray.
PROGRAM
Accesses or removes program menu.
CLEAR
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
0-9 number buttons
Selects numbered items in a menu.
•FWD ( TT )
Search forward*/ go to next chapter
or track.
•PLAY ( 22)
Starts playback.
•REV ( SS )
Search backward*/ go to beginning
of current chapter or track or go to
previous chapter or track.
* Press and hold button for about
two seconds.
SELECT/ENTER
Acknowledges menu selection.
11 22 33 44 (left/right/up/down)
Selects an item in the menu.
•REPEAT
Repeat chapter, track, title, all.
•A-B
Repeat sequence.
•DISC SKIP
Moves to the next available disc tray.

INTRODUCTION
9
Rear Panel
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
Dust protection cap
Remove the dust protection cap from the OPTICAL
DIGITAL OUT jack and connect the optical digital cable
(not supplied) securely so that the configurations of
both the cable and the connector match. Keep the dust
protection cap and always reattach the cap when not
using the connector to protect against dust intrusion.
Dust protection cap
COAXIAL (Digital audio out jack)
Connect to digital (coaxial) audio equipment.
VIDEO OUTPUT Switch
Select either S-VIDEO or COMPONENT, depending on
how you connect DVD Player to the TV.
OPTICAL (Digital audio out jack)
Connect to digital (optical) audio equipment.
COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y PBPR)
Connect to a TV with Y PBPRinputs.
ANALOG AUDIO OUT (Left/Right) 1, 2
Connect to an amplifier, receiver or stereo system.
VIDEO OUT
Connect to a TV with video inputs.
AC Power Cord
Plug into the power source.
S-VIDEO OUT
Connect to a TV with S-Video inputs.

10
Connections
Tips
Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the player. Use only one of the connections
described below.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
For better sound reproduction, connect the player’s
AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment.
See “Connecting to optional equipment”on page 11.
Caution
–
Make sure the DVD Player is connected directly to the
TV. Select the TV to the corresponding video input.
–Do not connect the DVD Player’s AUDIO OUT jack to
the phono in jack (Turntable) of your audio system.
–Do not connect your DVD Player via your VCR. The
DVD image could be distorted by the copy protection
system.
Connecting to a TV
Make one of the following connections, depending on
the capabilities of your existing equipment.
When using the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks, set the VIDEO
OUTPUT switch to COMPONENT. When using the
S-VIDEO OUT jack, set the VIDEO OUTPUT switch
to S-VIDEO.
Video connection (Good)
11
Connect the VIDEO OUT jack on the DVD Player to
the video in jack on the TV using the video cable
supplied (V).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD Player to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
S-Video connection (Better)
11
Connect the S-VIDEO OUT jack on the DVD Player
to the S-Video in jack on the TV using an optional
S-Video cable (S).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD Player to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Component Video (Color Stream®) connection (Best)
11
Connect the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks on the DVD Player to
the corresponding in jacks on the TV using an
optional Y PBPRcable (C).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD Player to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Progressive Scan (ColorStream®pro) connection
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD
Player’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan for-
mat, the picture will appear scrambled if you select
Progressive Scan output from the DVD Player.
11
Connect the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks on the DVD Player to
the corresponding in jacks on the TV using an
optional Y PBPRcable (C).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD Player to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Notes
–Set the Progressive to “On”from the setup menu, see
page 13.
–Progressive scan does not function simultaneously
with the analog video connections (yellow VIDEO
OUT jack).
Note
If the TV has an S-video input, connect the DVD player
with the S-video cable. When using an S-video cable,
do not connect the yellow video cable.
P R
P B
Y
COMPONENT VIDEO /
PROGRESSIVE SCAN INPUT
L
R
AUDIO INPUT VIDEO
INPUT S-VIDEO
INPUT
Rear of TV
Rear of DVD player
SA V C

11
PREPARATION
Connections (Continued)
Connecting to Optional Equipment
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
Connect the Left and Right AUDIO OUT jacks on the
DVD Player to the audio left and right in jacks on your
amplifier, receiver or stereo system, using the supplied
audio cables (A).
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby Digital™, MPEG 2 or DTS)
11
Connect one of the DVD Player’s DIGITAL AUDIO
OUT jacks (OPTICAL Oor COAXIAL X) to the cor-
responding in jack on your amplifier. Use an option-
al digital (optical Oor coaxial X) audio cable.
22
You will need to activate the player’s digital output.
(See “Digital Audio Output”on page 14).
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD Player (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Notes
–
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
–Six Channel Digital Surround Sound can only be
obtained if your receiver is equipped with a Digital
Multi-channel surround sound decoder.
–To confirm the audio format of the current DVD
selection display, press AUDIO.
–Repeated pressing of the AUDIO button may allow
you to select between various audio formats available
on the disc.
Note
This player does not perform internal (2 channel)
decoding of a DTS sound track. To enjoy DTS
multi channel surround, you must connect this player to
a DTS compatible receiver via one of this player’s
digital audio outputs.
Amplifier (Receiver)
Rear of DVD player
A XO
L
R
AUDIO INPUTDIGITAL INPUT
OPTICAL COAXIAL
DIGITAL INPUT

12
Before Operation
General Explanation
This manual gives basic instructions for operating the
DVD Player. Some DVDs require specific operation or
allow only limited operation during playback. When this
occurs, the symbol appears on the TV screen, indi-
cating that the operation is not permitted by the DVD
Player or is not available on the disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
11
Press GUI DISPLAY during playback.
22
Press 33or 44to select an item.
The selected item will be highlighted.
33
Press 11or 22to change the setting of an item.
The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press SELECT/ENTER to execute the setting.
Repeat mode Icons
Repeat Title
Repeat Chapter
Repeat Track (Audio CD only)
Repeat All Tracks (Audio CD only)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
Notes
Some discs may not provide all of the features includ-
ed on the on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
OFF
A B
ALL
TRACK
CHAPT
TITLE
Items
Title Number
Chapter Number
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
Sound
Function (Press 33 /
44to select desired item)
Displays the current title number and total number of
available titles, and skips to a desired title number.
Displays the current chapter number and total number of
available chapters, and skips to a desired chapter number.
Displays the elapsed playing time, and
searches a point identified by its elapsed time.
Displays the current audio soundtrack language,
encoding method and channel number, and
any changes you make to the setting.
Displays the current subtitles language, and
any changes you make to the setting.
Displays the current angle number and total number of
angles, and any changes you make to the angle number.
Displays the current sound mode, and
any changes you make to the setting.
Selection Method
11 / 22, or Numbers,
SELECT/ENTER
11 / 22, or Numbers,
SELECT/ENTER
Numbers,
SELECT/ENTER
11
/
22
11
/
22
11
/
22
11
/
22
1/3
1/12
0:16:57
1 ENG
D
6 CH
OFF
1/1
NORM.
Items
Track Number
Time
Audio Channel
Sound
Function (Press 33 /
44to select desired item)
Displays the current track number, total number of tracks,
and skips to the desired track number.
Displays the elapsed playing time (Display only)
Displays the audio channel, and
changes you make to the audio channel.
Displays the current sound mode, and
any changes you make to the setting.
Selection Method
11
/
22
,or Numbers,
SELECT/ENTER
–
11
/
22
11
/
22
1/4
0:16:57
STER.
NORM.
DVD
CD

PREPARATION
13
Before Operation (Continued)
Initial Settings
You can install your own Personal Preferences.
Initial Settings General Operation
11
Press SETUP.
The setup menu appears.
22
Press 33/44to select the desired item.
The screen will display the current setting for the
selected item, as well as alternate setting(s).
33
While the desired item is displayed, press 22,
then 33/44to select the desired setting.
44
Press SELECT/ENTER to confirm your selection.
Some items require additional steps.
55
Press SETUP, RETURN or PLAY to exit the
setup menu.
Language
Disc Language
Select a language for the disc’s Menu, Audio and
Subtitle.
Original : The original language included on the disc is select-
ed.
Other : To select another language, enter the 4-digit number
corresponding to the language code list on page 25. If you
enter the wrong language code, press CLEAR.
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Picture
TV Aspect
4:3 Letterbox: Select when a standard 4:3 TV is con-
nected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a standard 4:3 TV is con-
nected. Displays pictures cropped to fill your TV screen.
Both side of the original picture may be cut off.
16:9 Wide: Select when a 16:9 wide TV is connected.
Progressive Scan
Progressive Scan Video provides the highest resolution
pictures with less flicker and line structure.
If you are using the COMPONENT VIDEO OUT/
PROGRESSIVE SCAN jacks, but are connecting the
DVD Player to a standard (analog) television, set
Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Note
–Progressive Scan is available only when the VIDEO
OUTPUT switch on the rear panel is set to COMPO-
NENT/PROGRESSIVE SCAN.
Caution
Once the setting for progressive scan output is entered, an
image will only be visible on a progressive scan compatible
TV or monitor. If you set Progressive Scan to On in error,
you must reset the unit. Pointing the remote at the player,
press the STOP key to stop any disc that is playing. Next,
press the STOP key again and hold it for five seconds
before releasing it. The video output will be restored to the
standard setting, and a picture will once again be visible on
a conventional analog TV or monitor.
DVD
DVD
DVD
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio Original
Spanish
English
Chinese
Polish
Hungarian
Russian
French
German
Italian
Other ————
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
PiS
Disc Audio English
Spanish
French
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio Off
On
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio 4:3 Letterbox
4:3 Panscan
16:9 Wide
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio Original
Spanish
English
Chinese
Polish
Hungarian
Russian
French
German
Italian
Other ————

14
Before Operation (Continued)
Sound
Digital Audio Output
Each DVD disc may have a variety of audio output
options. Set the player’s Digital Audio Output according
to the type of audio system you use.
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM”
if you connect the DVD Player’s DIGITAL OUT jack to a
Dolby Digital decoder (or an amplifier or other equip-
ment with a Dolby Digital decoder).
Stream/PCM: Select “Stream/PCM”if you connect the
DVD Player’s DIGITAL OUT jack to an amplifier or other
equipment with a DTS decoder, Dolby Digital decoder
or MPEG decoder.
PCM: Select when connected to a 2 channel digital
stereo amplifier. The DVD player outputs sounds in the
PCM 2ch format when you play a DVD video disc
recorded on the Dolby Digital, MPEG1 or MPEG2
recording system.
Sample Frequency
To change the Sample Frequency setting, first select
the desired Digital Audio Output as indicated above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz
signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass all signals through without
down conversion, or processing.
Others
The DRC and Vocal settings can be changed.
Press 33/44to select the desired item and press
SELECT/ENTER. The setting of the selected item
alternates between On and Off.
Dynamic Range Control (DRC)
With the DVD format, you can hear a program’s sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Vocal
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio DRC Off
Vocal On
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio DOLBY
DIGITAL /PCM
Stream/PCM
PCM
Sample Freq.
48 KHz
96KHz

PREPARATION
15
Before Operation (Continued)
Parental Control
Rating
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
11
Select “Rating”on the Setup menu using the 33
and 44buttons.
22
While “Rating”is displayed, press 22.
33
When you have not entered a password yet;
Install a 4-digit password using the number buttons
to create a personal 4-digit security password, then
press SELECT/ENTER. Enter the 4-digit password
again and press SELECT/ENTER to verify.
When you have already entered a password;
Install your 4-digit password using the number
buttons to confirm the personal 4-digit security
password, then press SELECT/ENTER.
If you make a mistake before pressing SELECT/ENTER,
press CLEAR and install your 4-digit security password
again.
44
Select a rating from 1 to 8 using the 33/44but-
tons. One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play without restrictions.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the play-
er, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found,
playback will stop. You must enter your 4-digit
password or change the rating level in order to play
the disc.
55
Press SELECT/ENTER to confirm your rating
selection, then press SETUP to exit the menu.
Country Code
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 26.).
11
Select Country Code using the 33/44buttons on
the setup menu.
22
While Country Code is selected, press 2.
33
Follow step 3 of “Rating”on left.
44
Select the first character using the 33/44buttons.
55
Shift the cursor using 11/2buttons and select
the second character using 33/44buttons.
66
Press SELECT/ENTER to confirm your country
code selection, then press SETUP to exit the
menu.
Note
Confirmation of your 4-digit password is necessary
when the code is changed (see “Changing the 4-digit
code”below ).
Changing the 4-digit code
1Follow Steps 1-2 as shown above to the left (Rating).
2Install your old code, then press SELECT/ENTER.
3Select Change using the 33/44buttons then press
SELECT/ENTER.
4Install the new 4-digit code, then press
SELECT/ENTER.
5Install exactly the same code a second time and veri-
fy by pressing SELECT/ENTER.
6Press SETUP to exit the menu.
If you forget your 4-digit code
If you forget your password, to clear the current pass-
word, follow the procedure below.
1Press SETUP to display the setup menu.
2Use the Number buttons to enter the 6-digit number
“210499.”
The 4-digit password is cleared. “P CLr”appears on the dis-
play. The message will appear if the disc tray is closed. It
will be on the display until you try another feature.
3Enter a new code as shown above to the left (Rating).
DVD
DVD
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio Code Set
U S
Disc Subtitle
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
5.1 Speaker Setup
Others
Disc Audio 8
7
6
5
4
3
2
1
Unlock
Change

16
Operation with DVD and Audio CD
Playing a DVD and Audio CD
Playback Setup
Turn on the TV and select the video input source
corresponding to the DVD player.
Audio system: Turn on the audio system and select
the input source connected to the DVD player.
11
Press OPEN/CLOSE to open the disc tray.
22
Load your disc in the tray, with the label facing
up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing up.
•Discs can be loaded one at a time by pressing
DISC SKIP to rotate the carousel.
33
Press OPEN/CLOSE to close the tray.
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu may appear instead.
If a disc menu screen is displayed
The menu screen may be displayed first after loading a
DVD that contains a menu.
Use the 11 22 33 44 buttons to select the title/chapter
and additional selections you want, then press
SELECT/ENTER to start playback.
Press TITLE or MENU to return to the disc menu
screen.
Notes
–If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 15).
–DVDs may have a region code.
–Your player will not play discs that have a region code
different from your player. The region code for this
player is 1 (one).
Exchanging discs during playback
Press DISC EXCHANGE on the front panel during
playback to open the disc tray.
Press DISC SKIP to rotate the disc trays to the
desired position. The carousel will rotate clockwise by
one disc increments.
Exchange the discs and press DISC EXCHANGE or
OPEN/CLOSE to close the disc tray.
Note
–The disc tray presently loaded in the play position can
not be exchanged.
Skipping discs
Press DISC SKIP during play or when playback is
stopped.
Notes
–When DISC SKIP is pressed, the disc tray rotates and
playback begins from the beginning of the next disc.
–If there is no disc on the next disc tray, the following
disc tray will be selected.
–When DISC SKIP is pressed during playback of disc
5, playback of disc 1 will start.
Exchanging the disc and starting playback
1.Press OPEN/CLOSE during playback or when play-
back is stopped.
Play stops (if pressed during playback), the disc tray opens
and the disc that was in the play position comes to the front.
2.Exchange the disc.
3.Press OPEN/CLOSE or PLAY again.
The tray closes and playback begins (with the disc
that was in front).
DVD
CDDVD

Operation with DVD and Audio CD (Continued)
General Features
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available from the Setup menu.
Moving to another TITLE
When a disc has more than one title, you can select to
another title as follows:
Press GUI DISPLAY when playback is stopped.
From the title function, press the appropriate num-
bered button (0-9) to select a title number.
Moving to another CHAPTER/TRACK
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
Press REV .or FWD >briefly during playback
to select the next chapter/track or to return to the
beginning of the current chapter/track.
Press REV .twice briefly to step back to the pre-
vious chapter/track.
To go directly to any chapter during DVD playback,
press GUI DISPLAY. Then, press 33/44to select C
(chapter) (or for an Audio CD, select T for track).
Then, enter the chapter/track number using the num-
bered buttons (0-9).
Note
For two-digit numbers, press the buttons in rapid
succession.
Still Picture and Frame-by-frame playback
1Press PAUSE/STEP during playback.
The player will now go into PAUSE mode.
2You can advance the picture frame by frame by
pressing PAUSE/STEP repeatedly on the remote
control.
Pause
1Press PAUSE/STEP during playback.
2To return to playback, press PLAY or press
PAUSE/STEP again.
Slow Motion
1Press SLOW tor Tduring playback.
The player will enter SLOW mode.
2Use the SLOW tor Tto select the required speed:
t 1/16, t 1/8, t 1/4 or t 1/2 (reverse), or T
1/16, T1/8, T1/4 or T1/2 (forward).
3To exit slow motion mode, press PLAY.
Search
1Press and hold REV .or FWD >for about two
seconds during playback.
The player will now go into SEARCH mode.
2Press and hold REV .or FWD >repeatedly to
select the required speed: mX2, mX4, mX16,
mX100 (backward) or MX2, MX4, MX16,
MX100 (forward).
3To exit SEARCH mode, press PLAY.
Random
1Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM (1-3)”appears on the TV screen.
•RANDOM1: Plays all the tracks on a single disc in random
order and then stops.
•RANDOM2: Plays all the tracks on current disc in
random order and then plays all the tracks on each suc-
ceeding disc in random order and then stops.
•RANDOM3: Plays 2 tracks randomly from a disc and then
plays 2 tracks randomly from a different disc until all
tracks on all discs have been played.
2To return to normal playback, press RANDOM until
“RANDOM”disappears on the display window.
Tip
By pressing REV .or FWD >during Random
playback, the unit selects another title (track) and
resumes Random playback.
Note
This function works only with Compact Discs and
Karaoke discs.
CDKaraoke DVD
CDDVD
DVD
CD
DVD
1/31/12
CDDVD
1/3
DVD
OPERATION
17

Operation with DVD and Audio CD (Continued)
General Features (cont’d)
Repeat
DVD Video Discs - Repeat Chapter/Title/Off
1
To repeat the chapter currently playing, press REPEAT.
The Repeat Chapter icon appears on the TV screen.
2To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Audio CDs - Repeat Track/Disc/All/Off
1To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the TV screen.
2To repeat the disc currently playing, press REPEAT a
second time.
The Repeat Disc icon appears on the TV screen.
3To Repeat of entire all disc contents, press REPEAT a
third time.
The Repeat All icon appears on the TV screen.
4To exit Repeat mode, press REPEAT a fourth time.
The Repeat Off icon appears on the TV screen.
Repeat A-B
To repeat a sequence in a title:
1Press A-B at your chosen starting point.
A- appears briefly on the TV screen.
2Press A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat sequence
begins (a-b repeat appears on the player’s display).
3To cancel the sequence, press A-B.
Time Search
The Time Search function allows you to start playing at
any elapsed time location on the disc.
1Press GUI DISPLAY during playback. The on-screen
display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
2Within 10 seconds, press 33/44to select the Time
Search icon in the on-screen display.
The “-:--:--”appears in the Time Search box.
3Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes and sec-
onds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press SELECT/ENTER to confirm the
start time.
Playback starts from the selected time on the disc. If you
enter an invalid time, playback will continue from the current
point.
3D Surround
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multi-
channel audio from a home theater system.
1Press DISPLAY during playback.
2Press 3or 4to select the sound option.
The sound option will be highlighted.
3Press 1or 2to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM”.
Zoom
The Zoom function allows you to expand the video
image and to move the focus point of zoomed image.
1Press ZOOM during playback or still playback to acti-
vate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six times.
2Use the 11/22/33/44buttons to move the focus point off
the zoomed image.
3Press CLEAR to resume normal playback or return to
the paused image.
Notes
The zoom function may not work for some DVDs.
The zoom function may not work on multi-angle
scenes.
DVD
3D SUR
NORM.
DVD
-:--:--
0:16:57
DVD
OFF
A B
A *
CDDVD
OFF
ALL
DISC
TRACK
TITLE
CHAPT
CDDVD
18

OPERATION
19
Operation with DVD and Audio CD (Continued)
General Features (cont’d)
Marker Search
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1During disc playback, press MARKER at the location
you want to memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a disc.
To Recall a Marked Scene
1During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2Within 10 seconds, press 1/2to select a Marker num-
ber that you want to recall.
3Press SELECT/ENTER.
Playback will start from the Marked scene.
4To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2Press 1/2to select the Marker number that you want
to erase.
3Press CLEAR.
The Marker number will be erased from the list.
4Repeat steps 2 and 3 to erase additional Marker
numbers.
5
To remove the MARKER SEARCH menu, press SEARCH.
Note
All disc markers are cleared when the power is turned
off or the disc is removed.
Special DVD Features
Checking the contents of DVD Video
discs: Menus
DVDs may contain menus that allow you to access spe-
cial features. To access the disc menu, press MENU.
Then, press the appropriate number button to select an
option. Or, use the 1/2/3/4buttons to highlight your
selection, then press SELECT/ENTER.
Title Menu
1Press TITLE.
If the current title has a menu, that menu will appear on the
screen. Otherwise, the disc menu may appear.
2The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3To remove the title menu, press TITLE again.
Disc Menu
1Press MENU.
The disc menu is displayed.
2To exit the disc menu, press MENU again.
Camera Angle
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
Changing the Audio Language
Press AUDIO repeatedly during playback to hear different
audio languages or audio tracks available on the disc.
Changing the Audio Channel
Press AUDIO repeatedly during playback to hear a dif-
ferent audio channel (STEREO, LEFT or RIGHT).
Subtitles
Press SUBTITLE repeatedly during playback to view
the different subtitle languages available on the disc.
Note
If appears, the feature is not available on the disc.
1 ENG
DVD
RIGHT
LEFT
STER.
CD
1 ENG
D
6 CH
DVD
1/1
DVD
DVD
DVD
DVD
MARKER SEARCH
1/9
CDDVD

20
Programmed Playback with Audio CD
Programmed Playback with Audio CD
11
Insert a Audio CD and close the tray.
22
Press PROGRAM while playback is stopped.
The Program menu will appear.
Note
Press PROGRAM or RETURN to exit the Program
menu.
33
Enter the disc number using the numerical keys
(1-5) and then press SELECT/ENTER.
44
Enter the track number using the numerical
keys (0-9) and then press SELECT/ENTER.
The next area is selected.
55
Repeat steps 3 to 4.
Up to 20 tracks can be programmed.
66
Press PLAY to exit the menu.
The selected tracks are stored in the player memory and
playback begins with the first programmed sequence.
77
After playback of all programmed tracks is com-
pleted, playback is stopped
Tip
After playback of all programmed tracks is completed,
playback is stopped.
Repeat Programmed Tracks/All
To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the menu screen.
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat All icon appears on the menu screen.
To cancel Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the menu screen.
To resume normal playback from programmed
playback
Press and hold PROGRAM until “PROG.”indicator dis-
appears in the display window.
Erasing a Track from Program List
1Press PROGRAM while playback is stopped.
The Program menu will appear.
2Use 1/2/3/4to select the track that you wish to erase
from the Program list.
3Press CLEAR.
The track will be erased from the Program list.
Erasing the Complete Program List
1Press PROGRAM while playback is stopped.
The Program menu will appear.
2Use 1/2/3/4to select “Clear All”, then press
SELECT/ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
Step 1
Program
Clear All
1