studioduc juno User manual
juno crib
a how-to guide that won’t leave you in tears.
ASSEMBLY INSTRUCTIONS
parenting is hard.
this is easy.
no really, it is.
MADE HERE™
MADE SAFE MADE SMART
MADE WELL™
thank you for selecting a
studio duc product!
Please check contents against the components list in these instructions. Also, please
ensure there was no damage that may have occurred in shipping.
If any components are missing or you find any damage, please contact ducduc before
continuing.
Read all the instructions before use of the crib.
Please remember to securely tighten all bolts and fasteners, and periodically check to
make sure every component is properly and securely in place and all bolts and fasten-
ers are tight.
Pay close attention to the safety warnings in these instructions and on crib labels.
A minimum of two people is required to safely assemble and move the crib. Do not
attempt to move this crib alone - dragging or sliding it across a floor may cause struc-
tural damage.
KEEP INSTRUCTIONS FOR FUTURE USE
OPERATION + MATTRESS PANEL ADJUSTMENT:
The mattress height should be lowered as your baby grows to ensure that
he/she does not climb out of the crib. When child is able to pull to standing
position, set mattress to lowest position and remove bumper pads, large toys
and other objects that could serve as steps for climbing out. Regularly assess
your baby’s abilities and make adjustments accordingly.
To adjust the height of the mattress support, remove the mattress from the
crib. Unscrew all four MATTRESS SUPPORT BOLTS E, remove all LOCKING
WASHERS G and FLAT WASHERS F and remove MATTRESS PANEL C. Remove
and re-insert the smooth ends of each MATTRESS SUPPORT PIN D in mattress
support holes on SIDE RAILS B at desired height. Refer to steps 8 through 9 for
re-inserting MATTRESS PANEL C and reattaching FLAT WASHER F, LOCKING
WASHERS G and MATTRESS SUPPORT BOLTS E.
MAINTENANCE:
Periodically check to make sure every component is properly and securely in
place and all bolts and fasteners are tight.
CLEANING:
Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever refinish
this furniture, be sure to use only a non-toxic finish specified for children’s
furniture.
STORAGE:
Store crib in a dry area.
WARNING
!
Failure to follow these warnings and the assembly instructions could result in serious
injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
Infants can suocate on soft bedding. Never add a pillow or comforter. Never place
additional padding under infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by your physician.
STRANGULATION HAZARD:
Strings can cause strangulation! Do not place items with a string around a child’s neck,
such as hood strings or pacifier cords. Do not suspend strings over a crib or attach
strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body
or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a
child.
FALL HAZARD:
When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for
climbing out.
Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm.).
Check this product for damaged hardware, loose joints, loose bolts or other fasteners,
missing parts, or sharp edges before and after assembly and frequently during use.
Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are
missing, damaged or broken. Contact ducduc for replacement parts and instructional
literature if needed. DO NOT substitute parts.
If refinishing, use a non-toxic finish specified for children’s products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they
can cause suocation.
Infants can suocate in gaps between crib sides and a mattress that is too small.
WHAT’S IN THE BOX:
A (x2)
end panel
B (x2)
side rail
C
mattress panel
D (x4)
mattress support pin
E (x4)
mattress support bolt
F (x4)
5/16” flat washer
G (x4)
5/16” locking washer
WHAT YOU’LL NEED:
15 minutes
(or less)
2 people
plus a dog for moral support
(unless you’re a cat person)
phillips head screwdriver
1Lean A against the wall.
*duc insider tip*
Steps in this assembly will require parts to be
flat on the floor.
Assemble on a soft surface to prevent any
damage. Try a rug, a blanket, or even a sheet
of foam from the packaging!
still confused? scan this code to watch the assembly video!
Insert B connectors into slots on right side of A.
2
still confused? scan this code to watch the assembly video!
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
**be sure the (4) holes are in
the bottom interior position
when connecting both (B) parts
to both (A) parts**
Push B down to lock connectors into place.3
still confused? scan this code to watch the assembly video!
Repeat STEPS 2 + 3 to lock remaining part B into place.4
still confused? scan this code to watch the assembly video!
5Insert the connectors on both parts B into slots on remaining part A.
still confused? scan this code to watch the assembly video!
Push both parts B down to lock connectors into place.6
still confused? scan this code to watch the assembly video!
Insert hardware D (qty: 4) into the top hole on each side of B. Make sure hardware D is the
same height on all 4 sides.
7
*duc insider tip*
If you‘re setting up the crib for a newborn, start with the mattress panel
in the highest position (hardware in the top most holes).
As baby gets older, adjust the mattress panel to the lower
settings as needed for more space. See operation + mattress panel
adjustment instructions on page 5.
still confused? scan this code to watch the assembly video!
8Place C into the crib so each piece of hardware D is inserted into a hole.
*duc insider tip*
Tilt C down as shown when placing inside the crib for an easy
and smooth transition.
still confused? scan this code to watch the assembly video!
9Place hardware G and F as shown in detail onto C, then screw in hardware E using a phillips
head screwdriver. Repeat on all four sides.
still confused? scan this code to watch the assembly video!
yipee! you did it!
give yourself a pat on the back, take a bow,
or go house a pint of ice cream…we don’t judge.
Other manuals for juno
1
Other studioduc Baby & Toddler Furniture manuals
