Stur-D-Stor LSS-482484 Instruction Manual

CONGRATULATIONS on your
selection of Tennsco’s STUR-D-STOR
home shelving system. The
STUR-D-STOR system is designed for
use in the home, the office, and the
industrial workplace. STUR-D-STOR
shelving systems provide sturdy
shelving which may be used as either a
single upright unit or split in half to
provide shelving with a handy work
surface. Our unique shelf support
design provides support for loads of up
to 850 pounds per shelf!
ASSEMBLY INSTRUCTIONS & PARTS MANUAL #1090703
HOME SHELVING SYSTEM,
Model No. LSS-482484
STUR-D-STOR, Dickson, TN 37056-1888 * [phone]
Be Sure To Save This Instruction Sheet For Future Reference!
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when
handling various pieces to avoid injury. For safety, wear a pair of
work gloves when assembling or performing any maintenance on
shelving unit. Shelvingunit is designed to be placed upright on a flat
surface. Distribute the weight of items stored on the shelves evenly
acrosstheshelves.Donotplaceheavieritemsontheuppershelves.
Iftheshelvingunitistobelocatedinanunevenmannerorpositioned
on an unlevel surface, the unit should be secured to a wall or floor
with appropriate fasteners. Do not use as a ladder!
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects
in materials and workmanship for a period of one (1) year from the
date of shipment, hereunder. This warranty shall not apply in the
event goods are damaged as a result of misuse, abuse, neglect,
accident, improper application, modification or repair by persons not
authorized by Seller, where goods are damaged during shipment, or
where the date stampson the goods have beendefaced, modified or
removed. UNLESS CONSIDERED UNENFORCEABLE OR
UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES,INCLUDING BUT NOTLIMITED TO
WARRANTIES OR MERCHANT ABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY EXCLUDED.
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS
SHALL BE LIMITED TO A REFUND BY SELLER OR
REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND
SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND,
WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR
APPROVAL. Seller shall have the right to inspect any goods claimed
to be defective at Buyers place of business or require Buyer to return
the goods to Seller for inspection on Seller’s premises. Transportation
charges covering returned goods will be borne by Seller only if such
goods are proven to be defective, are covered bythis warranty andare
returned within the warranty period stated above.

Step By Step Installation Instructions
Tool required: Rubber Mallet or Hammer
1. Remove all parts from carton and
check against the parts list on back
cover for any missing parts.
3. Place a second
18" wide upright
halfway up the
upright assembly
as shown.
2. Connect two upright posts (Ref. A) with a
18" wide shelf support (Ref. B) by
inserting shelf support rivets into the
bottom two keyhole slots of each upright.
Use a rubber mallet to seat the upright
securely in the keyhole slots.
NOTE: Make sure that the narrow
end of the keyhole slots are pointing
downward, and that the flat edge of
the shelf support is facing up, as
shown in exploded view below.
4. Repeat steps 2 and 3 to
prepare a second set of
uprights, as shown. You should
now have two upright end
assemblies.
A
B
A
5. Place the two end
assemblies about 36"
apart, with the angled corners
facing outward. Connect two 36"
shelf supports (Ref. C) between the
two assemblies, one on each side,
as shown. Be sure to use the two
keyhole slots nearest the floor, as
before.
NOTE: As in step two, make sure the flat edge of the
shelf supports are facing upward. If you have done this
correctly, there should now be a flat surface around all
four edges on which to lay the bottom particleboard
shelf. If any edge has an upward-facing angled edge, the
upright has been inserted upside-down.
C
C

11. Place one particleboard
shelf (Ref. D) in each of
the five levels you have
created, slanting each
shelf slightly as you are
placing it to allow it to
fit between the uprights
and shelf supports. Make sure
each shelf is seated between the
edges on all four shelf supports, and
that the shelf is laying flat. Your Stur-D-Stor
Shelving System is now ready for use.
6. Repeat step 5 halfway
up the post as shown
below.
8. Place another upright post
on the opposite side of
the one you just mounted.
Using the other side of the
same shelf support,
attach in the same way
described in step 7.
9. Repeat steps 7 and 8 on the
opposite end of the unit. Then,
attach the two ends by placing
two 36" shelf supports across the
width of the unit. Be sure to
mount as previously described.
10. Continue placing
shelf levels, one
level halfway
between the
center shelf and
the top, and one
level using the
top two keyhole
slots. Make sure
all shelf supports
are mounted with
flat side facing up.
7. Mount another upright post (Ref. A) to the top
of one of the other uprights and attach with
an 18" shelf support, mounting the bottom
rivet of the shelf support in the bottom upright
post, and the top rivet in the new upright post
,
as shown in the exploded view above.
NOTE: Be sure that the narrow end of
the keyhole slots of the new post are
pointing downward, and that the flat
side of the shelf support is facing
upward, as mentioned in previous steps
.
D
D
D
D
D

REF. NUMBER DESCRIPTION PARTS NO. QTY.
A Upright Post EUR-42 8
B Shelf Support (24" wide) VDRS-2416 10
C Shelf Support (48" wide) VDRS-4816 10
D Particleboard Shelf PBV-4824 5
ORDER REPLACEMENT PARTS DIRECT FROM FACTORY
Please Provide the following information: Contact: STUR-D-STOR, P.O. Box 1888
•Model Number Dickson, TN 37056-1888
•Part Description and Number as Shown Above [phone] [phone]
AB C D
Assembly as a Workbench/Shelf Unit
Tool required: Rubber Mallet or Hammer
Parts List
A. Follow steps one through
six on the inside of this
assembly sheet. B. Instead of stacking the
uprights on top of each other,
as shown in step seven inside
this sheet, place four shelf
supports in the top two
keyhole slots, being sure that
the flat edge of each shelf
support is facing up as
described in earlier steps.
C. Now, build the second unit in the same
manner as you did the first unit, except this
one with only two levels. Place the top
level in the top two keyhole slots, and the
second level at whatever
height you prefer (see
illustration).
D. Insert one
particleboard
shelf at each of
the five shelf levels, as
described in step 11 inside
this sheet. Then, place the two
units together, or use seperately as desired. Your
Stur-D-Stor Shelving System is now ready for use.