STW TCGi User manual

QUICK START GUIDE FOR STARTING UP
TCG with machines.cloud

1 Check the scope of delivery*1
Connect the antennas to the SMA plugs.
2 Configuring the SIM card
1. Press the yellow button
beside the card tray
2. Remove the SIM card holder
(for micro SIM cards or smaller
cards a corresponding
adapter is required)
3. Place the SIM card into the tray
4. Slide in the fitted holder carefully
TCGi Breakout cables
Cable
harness
adapter Power supply
TCGe 2G/3G/4G Wi-Fi/Bluetooth GPS/GLONASS
Optional:
*1Only with standard loan kit

3 Starting up TCG
1. Supply the TCG with power:
a. Set the power supply to 12 V
b. Connect the TCG to the breakout cables
c. Connect the breakout cables to the cable harness
adapter
d. Connect the power supply unit to the cable harness
adapter
e. ATTENTION: Select the correct power supply output
connectors
f. ATTENTION: Check the polarity of the power supply
output connectors
2. Switch on the cable harness adapter
3. Wait for the status LED of the TCG
ATTENTION: For (optimal) GPS and GSM reception, the TCG
must be positioned outside buildings

4 Status detection by LED light
Yellow Ready for use no Internet
access; GPS not active
or no GPS reception
The TCG lights up yellow
after switching on
Blue No Internet access;
GPS active After booting the TCG, it
may take a few minutes
for a GPS signal to be
received or for Internet
access to be established
Pink Internet access available;
GPS not active or no
GPS reception
Green Internet access
available; GPS active
Flashing Data traffic via CAN The flashing can occur
with all colors
Red
flashing
Error signal (see
operating instructions)
A restart of the TCG
is recommended
5 Establish a connection with
machines.insight
1. Connect your smartphone, tablet or PC to the TCG WiFi
network
Example with TC3G:
Network name:
TC3G-"serial number“
 Password:
see label on the TCG
2. Open address "192.168.201.1" in your browser
3. Click on "Login" in the left menu bar
4. Login data: Username: admin
Passwort: admin
machines.insight

6 Configuring machines.insight
1. Select "System" in the left menu bar
2. Switch to Wi-Fi within
"Network Configuration“
3. Select the "Access Point"
window on the right
4. Change the password for
Wi-Fi access
5. Click on "Save"
6. Switch to "machines.cloud"
within the "Network
Configuration"
7. Switch the Activate connec-
tor to "ON"
8. Click on "Save"
9. Switch to GSM within
"Network Configuration"
10. Does the SIM card already
have a PIN? Set the PIN
switch in the GSM window to
"Yes" and enter the PIN
11. Set GSM status to "ON"
12. Click on "Save" and restart the TCG (switch off/on the cable
harness adapter)
ATTENTION: With M2M SIM cards further configurations
are necessary (Point 7 )

7 Configuring a M2M SIM card (only
necessary for M2M SIM cards)
1. Login as "admin" in machines.insight
2. Navigate to "System" "Network Configuration" "GSM"
3. Select the "Custom Configuration" field on the right
4. Enter M2M parameters (source: SIM card provider)
5. Click on “Save" and restart the TCG (switch off/on the
cable harness adapter)

8 Registration in machines.cloud and
first steps
1. Open the e-mail from
no-[email protected]
with the link to the cloud
2. Click on the link and change your password on the web
page
3. Log in with the new access data
User name: tenantname_admin
4. Top right click on "<<"
5. In the area of “Help & Support” click on “T.O.N.I.”*2and
then on “Show Tours”
6. The following tours are available:
a. Register Device
b. m.a Welcome Page
c. Create / Use VPN
d. Track Evaluation
e. Data Explorer
f. Codesys Gateway
*2Trusted Online Navigation Instructor

Sensor-Technik Wiedemann GmbH (STW)
Am Bärenwald 6
87600 Kaufbeuren
Telephone: [phone]
Telefax: [phone]
[email protected]
www.stw-mm.com
Further Information
Video Tutorials:
German: youtu.be/UTl4E_I39sE
English: youtu.be/dJcDs7t28yw
All Manuals and Tutorials here:
stw-digitalization.com
Password: connectivity
T.O.N.I. Tours:
Available in machines.cloud and machines.access
Top right click on „<<“
20190415–86876-EN–Irrtümer und Änderungen vorbehalten