Summit Treestands Ultimate Viper User manual

21072 HARDWARE KIT ULTIMATE VIPER
PN Description QTY
10612 1/4” Lock Nut (1/4 -20) 2
10633 Neoprene Washer 2
10632 2 1/2” Carriage Bolt (1/4 -20) 2
10601 1 3/4” Bolt (1/4 -20) 2
10544 Gun Rest Adjustment Bracket 4
10660 Knob 2
20431 Gun Rest Mounting Bracket 2
Ultimate Viper Accessory Instructions
Part 1. Gun Rest
Step 1. Position the gun rest mounting bracket as shown in Figure
1. The bracket MUST be placed at least 3” up the arm to provide
clearance for the platform when the stand is packed together. The
long side of the bracket should go on the outside of the stand.
Warnings and Precautions
NEVER SIT ON THIS GUN REST OR ATTEMPT TO USE IT AS A
CLIMBING AID!
•
ULTIMATE VIPER ACCESSORIES AND PARTS LIST
PN Description QTY
40104 Gun Rest Tube 1
10950 Comfort Mat 1
11911 Drop Blind 1
21072 Hardware Kit 1
Figure 1
Step 2. Slide one 2 1/2” carriage bolt through the mounting bracket
from the inside out.
Step 3. Align one Gun Rest Adjustment Bracket as shown in
Figure 2. Slide the bracket over the carriage bolt and seat it on the
mounting bracket.
Step 4. Position the Neoprene washer as shown in Figure 2. Slide
the washer over the carriage bolt.
Step 5. Position another Gun Rest Adjustment Bracket as shown
below. The teeth should face inward. Slide the bracket over the
carriage bolt and seat it against the bracket/washer from Step 3.
Step 6. Slide the Gun Rest tube onto the outside bracket. Push the
carriage bolt through the pre-punched hole. Use the large knob to
secure.
Step 7. Repeat process for the other side. The carriage bolt may
have to be backed out slightly as you position the two Gun Rest
Brackets and the washer between the Gun Rest tube and the Seat
Base.
Step 8. Attach the 18” arm pad to the front of the bar using the
supplied cable ties.
Figure 2
Gun Rest Adjustment Brackets
Neoprene Washer
Carriage Bolt
Gun Rest Tube
Knob
If you have any questions or concerns about this or any Summit
product, please to not hesitate to call or email us:
www.summitstands.com
256-353-0634
Ultimate Viper Accessory - 2007 Instructions - PN 11807

Part 2. Drop Blind
Step 1. Your drop blind may ship unfolded. Lay the blind out on
a at surface. Start at the ends of the blind material and roll it up.
Once it is completely rolled, tuck it into the pocket and secure with
the long Velcro®strip that runs the entire length of the blind.
Step 2. Fold the blind in half and nd the center point. There
should be a Velcro®loop strap close to the center.
Step 3. Loop this Velcro®loop strap over the stand frame in the
middle of the front pad as shown in Figure 1.
Step 4. Work from the center back looping the straps over and
securing them as shown in Figure 2. Repeat for both sides.
Figure 1
Figure 2
Step 5. To use: Start at the back and unhook the long,
continuous Velcro®strap and let the blind drop around the stand.
Part 3. Comfort Mat
Step 1. The Comfort Mat has cutouts designed to t the standard
shape of the platform. Lay the mat between the platform arms as
shown in Figure 1.
Step 2. Make a small, 3/8”, incision through the mat just behind
the front bar. Insert one cable tie through the mat and around the
frame. Trim off the excess as shown in Figure 2.
Step 3. Make three more cuts in the locations shown in Figure 3.
Use the remaining ties to secure the mat to the stand.
Figure 1
Figure 2
Figure 3