Sunbeam Products 183952 User manual

SELF-CLEANING
LITTER BOX
SELF-CLEANING
LITTER BOX
QUICK START GUIDE
B
D
C
E
F
G
A
H
1.
Add litter to the FILL line in the Litter Tray (A) (see Fig. 9).
Your Automatic Litter Box works with most litter brands,
but clumping-type litter works best with this system.
2.
Locate the Power Adapter and plug it in to the outlet
on the side of the Detachable Motor (B). The outlet is
located underneath the Motor on the left side when
facing the Rake Assembly (E), as shown in Figure 10.
3.
Plug the Power Adapter into a standard household
wall outlet. The Control Panel LED lights will blink in
sequence while the unit is powering up and the first
Cleaning Cycle will begin automatically.
Figure 9
Figure 10
Figure 11
NOTE: If the Litter Box does not complete one Cleaning
Cycle, or if you hear the motor running but the Rake does
not move, please go back and review all previous steps.
4.
Choose the Cleaning Frequency on the Control Panel
by pressing the SELECT Button. The Litter Box will
automatically perform one Cleaning Cycle at the time
chosen. For example, if you select “Every 4 Hours”, the
Litter Box will complete a Cleaning Cycle once every 4
hours, as shown in Figure 11.
Select
Sleep
Mode
Hourly Every 4
Hours
Every 8
Hours
HOW TO USE
A. LITTER TRAY
B. DETACHABLE
MOTOR
C. SENSOR
D. CONTROL PANEL
E. RAKE ASSEMBLY
F. WASTE RECEPTACLE
LID w/ ODOR FILTER
G. WASTE RECEPTACLE
H. WASTE RECEPTACLE
LID HOLDER
© 2015 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.
Due to continuing product development, the product inside the packaging may look slightly different than the
one on the package. Sunbeam Products, Inc. is a subsidiary of Jarden Corporation (NYSE: JAH). Made in China.
The ARM & HAMMER™ name logo and associated marks are trademarks of Church & Dwight Co., Inc.
These marks are used under license by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions
P.N.: 183952 SPR-060815-247P

3.
Then push each
post of the Waste
Receptacle Lid (F)
into the hole at the
bottom of the slot on the
Waste Receptacle Lid Holder (H).
When installed correctly, both sides
of the lid should be level and feel
very secure in place. Ensure both
sides are firmly connected before
continuing (see Figure 3).
5.
Slide the
Waste
Receptacle
(with bag) into
place as shown
in Figure 5. Line the Receptacle up
under the opening so that no
waste will miss the Receptacle
(see Figure 5). There is a tab at
the end that will secure the waste
receptacle in place.
NOTE:
The Odor Filter is
pre-installed and
typically needs to be
changed monthly.
Be sure to remove the
plastic protective bag around the Odor
Filter before using it. You may need
to change the Filter more frequently
depending on your cat’s usage and the
number of cats in your household.
RAKE
A S SE M BLY
WASTE RECEPTACLE
A S SE M BLY
WASTE RECEPTACLE
LID ASSEMBLY
DETACHABLE MOTOR
A S SE M BLY
Figure 4
Figure 5 Figure 6
Figure 7
1.
The Rake
Assembly (E)
needs to be
installed. Slowly
slide the rake in
to the litter box tray wall.
Check to make sure that the Rake
Assembly (E) can move up and
down freely, and leave the Rake in
its lowest position before continuing
(see Figure 1).
2.
Install Waste
Receptacle Lid
Holder (H) by
pressing both sides
down into the litter box
tray (A) (see Figure 2).
4.
Place the
Drawstring Bag
into the Waste
Receptacle (G) ,
folding the sides
over the edges as shown
in Figure 4.
7.
After attaching, and while
holding the Detachable Motor
(B) to the back of the Litter Tray
(A), turn the blue Locking Knob
CLOCKWISE to lock the Motor
into place (see Figure 7).
6.
Locate the
Detachable Motor (B)
and align the tabs
with their corresponding
slots on the back of the
Litter Tray (A), as shown in Figure 6.
Figure 1 Figure 2
Figure 3
ASSEMBLY INSTRUCTIONS
SELF-CLEANING
LITTER BOX
SELF-CLEANING
LITTER BOX