Sunhope ECO Spot User manual

ECO SpotTM LED25 User Manual
Copyright © 2013 Sunhope Inc Page 1of 4
Thank you for choosing our ECO SpotTM LED25 Gobo
projector (SKU: ES-LED25). This unit is equipped with a fan
cooled 25W LED light bulb with 50,000 hours bulb life. No
more need for replacement bulbs.
Please read this manual before installing or operating this
fixture, follow the safety precautions listed below and observe
all warnings.
Package Contents
•Projector with power cord and integrated gobo holder and rotator
•Spare gobo retaining ring and spare drive belt
Safety Information
•This product is not for household use, it presents risks of severe injury or death due to fire
and burn hazards, electric shock, lamp explosion and falls.
•Place your fixture at a suitable place with good air flow.
•Keep flammable materials away from the fixture.
•Minimum distance to flammable material = 1 ft (0.3m).
•Minimum distance to illuminated surface = 3.3 ft (1.0m).
•Provide a minimum clearance of 4 in (10cm) around air vents.
•Use only genuine spare parts for part replacement.
•Do not look directly into the lamp; it can result in eye damage.
•Don’t touch the hot surface during operation, use gloves if necessary.
•Always unplug the unit from the power mains before any service is done.
•Allow 20 minutes to cool down before servicing the unit.
•Replace Lamps only with the same type other lamps may cause damage.
•Light fixtures should be installed and maintained only by qualified personnel with
experience in lighting equipment and general electrical experience.
Electrical Safety
•Disconnect the fixture from AC power before handling the fixture.
WARNING! Select the correct Line Voltage with the
selector on the back of the unit before Operating.

ECO SpotTM LED25 User Manual
Copyright © 2013 Sunhope Inc Page 2of 4
•Always ground (earth) the fixture electrically.
•Use only a power source that complies with local building and electrical codes and has
both overload and ground-fault protection.
•Do not use the fixture if the power cable or power plug is in any way damaged, defective or
wet, or if they show signs of overheating.
Handling Instructions
•Before the initial start-up, please unpack and carefully check for damage caused during
transportation.
•Place your fixture at a suitable place with good air flow.
•Make sure there are no flammable materials close to the lamp.
•When suspending the fixture above ground level, verify that the structure can hold at least
10 times the weight of all installed devices.
•Verify that all external covers and rigging hardware are securely fastened and use an
approved means of secondary attachment such as a safety cable.
Warranty
One Year from Date of Purchase
Focusing
•Power up the projector by pressing the larger switch in the back.
•Turn on the gobo rotator with the smaller switch in the back and switch it off when the
gobo projects in the desired position.
•Focus the projection by twisting the lens in and out until the image is well focused. When
used for the first time, the lens will often need to be twisted outwards many rotations to
reach the focusing point. This can take up to three minutes.
Lens Options
•Standard 20 degree (default)
•Optional lenses : Semi Narrow15 degree and Semi Wide 25 degrees
Gobo Rotator
•Turn on and off the gobo rotator with the small red button on the back plate
•There are no controls for rotating speed or direction.
Multi-functional Yoke
•The yoke can slide over the whole length of the fixture body to accommodate multiple

ECO SpotTM LED25 User Manual
Copyright © 2013 Sunhope Inc Page 3of 4
pointing directions.
•The yoke acts as a stand foot.
•The yoke can be screwed to a wall or ceiling or fastened with a C-clamp.
Gobo Replacement
•Unplug the power cord and let the projector cool down.
•Unscrew the four thumbscrews to remove the front cover with the projection lens.
•Push the two pins of the gobo retaining ring together and pull out the retaining ring.
•Carefully remove the old gobo and replace it with the new gobo. You may have to tilt the
projector forward for the gobo to fall out. Use caution, not to break the gobo, have it fall
into your hand.
•If you have a glass gobo, place the most reflective side towards the light bulb.
•Replace the retaining ring and make sure it evenly pushes the gobo all the way back.
•Replace the front cover and adjust the focus.

ECO SpotTM LED25 User Manual
Copyright © 2013 Sunhope Inc Page 4of 4
Specifications
Line Voltage (use the Line Voltage Selector in the back to select the correct line voltage.)
US/Canada Setting: 90-130V, 50-60Hz, 32W
International Setting (220V): 200-240V, 50Hz, 32W
Ambient Operating Temperature
-13 to 104°F (-25 to 40°C)
Gobo Dimensions
Metal or Glass Gobos and Dichroic filters
Outer Diameter (OD): 37.5mm (1.47 in)
Max. Image Diameter (ID): 25mm (1.0 in)
Max Thickness 4mm (0.16 in)
LED Lamp
The projector is equipped with a LED lamp that is designed to work for the full lifetime of the
projector. There is no need for a replacement lamp.
- Extremely high light density for ultra-efficient projection.
- Bulb life: 50,000h
- Color Temperature: 6,000K
- Rated Luminous Flux: 2000lm
- Effective Luminous flux: 870lm
- Not dimmable
Dimensions / Weight
Fixture Body: 11 x 7 x 3.75 in (L x W x H) (280 x 178 x 95mm), Add 0.5 to 2in (12-50mm) to the
length depending on the projection lens.
Height with Yoke: 7.75in (197mm)
Weight: 7lbs (3kg)
Sunhope Inc dba thegobo.com
Contact
2750 14th Ave., Unit G12-13, Markham, ON, L3R 0B6
www.sunhope.ca / www.thegobo.com
Tel: [phone]
Email: [e-mail]