Sunrection EF-2036F User manual

Electric Fireplace
EF-2036F User Manual
CONSUMER SAFETY INFORMATION
Read this manual before installing and operating this appliance.
Failure to follow these instructions may result in electric shock, fire conflagration,
or personal injury.
Do not store or use gasoline or other flammable liquids in vicinity of this appliance.
1.
2.
3.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

1.
2.
3.
4.
5.
IMPORTANT SAFETY INFORMATION!
WARNING
Read all instructions before using this heater!
This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at
least 3 feet (0.9m) from the front of the heater, and keep them away from the
sides and rear.
Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
DO NOT operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner.Discard heater,
or return it to authorized service facility for examination and /or repair.
DO NOT run power cord under carpet. DO NOT cover power cord with throw
rugs, runners, or similar coverings. DO NOT route power cord under furniture
or appliances. Arrange power cord away from the traffic area and where it will
be tripped over.
WARNING
Connect to properly grounded outlets ONLY.
DO NOT insert or allow foreign objects to enter any ventilation or exhaust
openings, as this may cause electric shock or fire, or damage the heater.
To prevent a possible fire, DO NOT block air intakes or exhaust in any manner.
Doing so could cause a fire. DO NOT use on soft surfaces, like a bed, where
openings may become blocked.
A heater has hot and arcing or sparking parts inside. DO NOT use it in areas
where gasoline, paint, or flammable liquids are used or stored.
Use this heater only as described in this manual. Any other use not recommend-
ed by the manufacturer may cause fire, electric shock, or injury to persons.
ALWAYS plug heaters directly into a wall outlet/receptacle. Never use with
an extension cord or relocatable power tap (outlet/power strip).
DO NOT place the heater near a bed because objects such as pillows or
blankets can fall off the bed and be ignited by the heater.
NEVER use this heater in bathrooms, laundry rooms, or any other location
where the heater could fall into a bathtub or pool, become damp or come in
contact with water.
AVOID FIRE! Regularly inspect all air vents to make sure they are free from dust,
lint, or other Blockage.Unplug the unit and clean with a vacuum ONLY.
DO NOT rinse or get wet.
ALWAYS mount to wall bracket before use. DO NOT set on the floor, or other
surface, to use.
-1-
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

PREPARATION
NEVER use a wall mount bracket from another manufacturer.
This product is not intended to be a primary heat source.
It is for supplemental heat only.
INDOOR use only! NEVER use this heater outdoors! Doing so may result in
electric shock!
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
ALWAYS turn this heater off before unplugging it from the outlet.
ALWAYS disconnect this unit from the power supply before performing any
assembly or cleaning, or before relocating the electric fireplace.
NEVER leave this heater unattended. ALWAYS unplug this heater when not in use.
ALWAYS store this heater in a dry location.NEVER use the fireplace if it has
become wet.
NEVER plug this heater into an outlet that is old, cracked, or has any loose wires
or connections. Plugging this heater into a faulty outlet could result in electric
arcing within the outlet that could cause the outlet to overheat or catch fire.
ALWAYS check your heater cord and plug connections when used each time!
i)MAKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or
loose plugs can cause the outlet to overheat.
ii)Heaters draw more current than small appliances. Overheating may occur
even if it has not occurred with the use of other appliances.
iii)During use check frequently to see if the plug outlet or face plate is HOT!
iv) If the outlet or face plate is HOT, discontinue use immediately and have
a qualified electrician inspect and/or replace the faulty outlets.
-2-
The power cord supplied with the heater
has a plug with two flat blades (live and
neutral) and one round pin (ground). If a
3-slot receptacle is not available,
an adapter MUST be used. The adapter
MUST be properly grounded to the
outlet box (see figure at right).
(Note:Adapter NOT INCLUDED.)
SAVE THESE INSTRUCTIONS!
This product includes a GLASS panel! Always use extreme caution when handing
glass. Failure to do so could result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a clean, soft, dry
surface. Parts and assembly steps are grounded for wall-hanging or recessing use.
Check the parts list to make sure nothing is missing. Dispose of packaging materials
properly. Please recycle whenever possible. You will need the following tools
(not included): Phillips screwdriver; stud finder; level; tape measure; electric drill; 1/4”
wood drill bit, hammer.
Grounding Pin
Adapter
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

-3-
PARTS & HARDWARE
Specification and Dimension
PRODUCT DIMENSIONS
A - Fireplace
B - Wood Screws
D - Decorative
Crystals E - Log set
C-Drywall anchors
Remote control
A
B
C
D
E
FG
N
M
u
o
m
d
b
e
e
l rA B C D E F G
EF-2036FU 36”
91.4CM
19”
48CM
6”
15.2CM
32.8”
83.3CM
18”
45.9CM
10.6”
27CM
29.7”
75.4CM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR
LACQUER MUST BE HEAT RESISTANT TO PREVENT DISCOLOURATION
PREPARATION
WARNING
-4-
Your appliance is a wall-mounted, recessed and /or mantel installed appliance. Select a
suitable location that is not susceptible to moisture and is away from drapes, furniture
and high traffic areas.
NOTE：Follow all National and local electrical codes.
MINIMUM CLEARANCE TO COMBUSTIBLES
Measurements are taken from the glass front.
Bottom 0”Top 11.8”(300mm) to mantel
Sides 0”Top 11.8”(300mm) to mantel
Back 0”
MANTEL
FLOOR
SIDE VIEW
11.8”(300mm)
MINUMUM MANTEL CLEARANCES
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

STEP A. Selection a dry wall to open a hole for fireplace box. Size of
hole as below chart.
STEP B. Punch 4 holes around the wall and install 4 Drywall anchors
(Part C), please drive C completely into the wall.
33.4”
Framing Hole Size
Model Number W H
EF-2036FU 33.4”(84.84cm) 18.8”(47.75cm)
18.8”
-5-
RECESSED TO WALL INSTALLATION
hole size
W
H
( A )
Wall Anchors
(4pcs)
33.8”
13.4”2.16”
W
H
( B )
Only qualified person can perform the installation.
WARNING
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

STEP C. Take off the screws (The fourth screw from top to bottom)in
both sides of fireplace. Figure (C)
STEP D. Remove packaging attachments from the log set.
STEP F. Take off the two screws in both sides of fireplace. Figure (C)
If the appliance is fully recessed into the wall:
Use the 4 screws(provided) to lock the appliance into wall with the
existing two side flanges, see Figure(F)
Install the media and re-install the glass front.
STEP G. Place the front panel lock the appliance. See Figure (G)
STEP H. Fireplace will be like this after installation Figure (H)
1.Remove the front grass.
2.Remove the pear cotton block.
3.Remove the log set’s packaging bag.
STEP E. Have two person to take the glass panel out of the fireplace
box. Place it to a soft and clean place. Figure (E)
-6-
（C）
（F） （G） （H）
（E）
The fourth screw
from top to bottom
hole size
W
H
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

Due to the many different materials used on different walls, it is highly recommended
that you consult your local builder before you install this appliance on the wall.
Wall Mounted Installation
-7-
1.You can see the 2 clips
on the back of the device. 2.Install 2 dry wall anchors
on the wall.
3.Two people lift the fireplace and
hang the 2 clips on the back on the
2 dry wall anchors.
B-Wood Screws C-Drywall anchors
28.5”
3.Install 2 wood screws, taking care
not to screw them in completely.
Screw head exposed 0.12-0.19inch
distance.
0.12-0.19inch
Only qualified person can perform the installation.
WARNING
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

Logset /Crystal Ember Installation
-8-
1.Remove the screws (The fourth screw from top to bottom) on both side
of the device to remove the front grass.
2.Take out the log set inside. 3.Put the decorative crystals in.
4.Install the glass plate.
The fourth screw from
top to bottom with
different color screw
Only qualified person can perform the installation.
WARNING
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

Read and understand this entire owner’s manual, including all safety
information, before plugging in or using this product. Failure do to so
could result in electric shock, fire, serious injury, or death.
WARNING
OPERATION INSTRUCTION：
-9-
Plug in a power plug hear a long buzzer and the electric fireplace is in standby mode.
Press the POWER key on the keyboard to show red, and the rest of the display is not
displayed. At this time, the electric fireplace is in standby mode.
Note: the ICONS on the keypad have the same function as the ICONS on the remote
control.
small remote control
Remove the romote control insulation sheet.
PULL
POWER
ICONS FUNCTIONS
Switch on/off button, turn on operation:
click the POWER button on keyboard or on remote control with a short buzzer
sound, the electric fireplace starts to work, the POWER button on the keyboard
with blue color, other keys with white color, the LED lights on the front and back
start to light up, the display window shows the room temperature .
turn off operation: click the POWER button on keyboard or on remote control
with a short buzzer sound, the LED light will be turned off, the electric fireplace will
be turned off, the heating will be turned off, the POWER button on the keyboard
will turn red to show all out, at this time, the fan which inside electric fireplace will
be continue to work for 10 seconds after stopped, then the electric fireplace is in
standby state.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

-10-
HEATER
TIMER
High Heating and Low heating setting:
If press "HEATER" button on keypad by 3 seconds,can switch between ℉and℃(Note:
this function is not available on the remote control.).Boot default setting temperature is
72℉(22℃), if the room temperature is lower than the setting temperature,Then the electric
fireplace high heating mode start to work, if you need electric fireplace heating work in
low heating mode, then click the keypad or remote control on the HEAT button to switch
the heating on high and low working mode ( first time press the button the display window
will display the current heating work mode, such as the current heating setting mode is
high heating then display window flicker HH, when you press the button once again, the
display window flicker LL, the heating mode become low heating, if you press the button
once again, then the display window flicker OO, the heating mode become OFF mode, if
you repeat press the HEAT button, then the heating mode will be working on HH-LL-OO
three kind mode in cycles), every time you press the button will have a short buzzer
sound, if you want to turn off the electric fireplace heating function, you can also operate
on the keypad or remote control setting temperature "DOWN" button.Make the setting
temperature is lower than the room temperature, then you can shut off the electric
fireplace heating function. When the heating is turned off, the fan which inside the electric
fireplace will continue to work for 10 seconds after stopped.
Timer Setting:
Timer can be set between 0 to12 hours, When turn on , the electric fireplace timing of
the default is 0 hours, you can operate the timer setting by the keypad or remote control
With the TIME button, After the electric fireplace on working, press the TIME buttons on
the keypad or on the remote control, then the display at the temperature display in the
display window changes to "00" and is flashing, at this time, every time you press the
button of the TIME in (0.5H-1.0H-1.5H-2H-2.5H-3H-3.5H-4H-4.5H-5H-5.5H-6.0H-6.5H-
7.0H-7.5H-8.0H-8.5H -9.0H-9.5H-10H-11H-12H) change, How long time you need it,
then you stop press, after display flashing by 10 seconds, if you not operate, the display
will be transferred back to the room temperature display and in a constantly light state.
Temperature setting increase buttons:
Temperature setting range is 60℉(15℃)-97℉(36℃), ( the default setting temperature is
72℉/22℃), press the UP button on the keypad or remote control, the temperature will
add 1℉/1℃each time. If long time press on it (don't loose the button), the temperature
will continue to increase until maximum(this long press function is not available on the
remote control.).When on temperature setting, the temperature display window is in a
flickering state. After notoperating the temperature setting button for 10S, the display
window will be turned back to the room temperature display and in a constantly bright
state.
Temperature setting decrease buttons:
Temperature setting range is 60℉(15℃)-97℉(36℃), ( the default setting temperature is
72℉/22℃), press the DOWN button on the keypad or remote control, the temperature
will reduce 1℉/1℃each time.If long time press on keypad,(don't loose the button) the
temperature will continue to decrease until the minimum.(Notethat this long press function
is not available on the remote control.) When on temperature setting, the temperature
display window is in a flickering state. After notoperating the temperature setting button
for 10S, the display window will be turned back to the room temperature display and in
a constantly bright state.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

13. Room temperature display error correction function:
When using this heater, if the heater's displayed room temperature is different with the
actual room temperature, you can use the temperature display error correction
function to correct the displayed room temperature, through long time press TIME key
on the keypad for 3 seconds, then the display window of room temperature normally
light change to temperature correction display.The digital display is in the flashing
display mode. When the first time use the temperature error correct function, pressing
the TIME button for 3 seconds, and the display window will be displayed as 0. At this
time, every time you press the up or down key on the remote control, the display
window will be up +1 or down -1 accordingly, and the correction range is between -9
and 9. After not operating on the heater for 10S, the display window will be turned
back to the room temperature display and in a constantly bright state.
-11-
LOCK
FLAME
DIMMER FUNCTION :
The flame brightness is on the brightest level by the first time. The flame brightness
have five levels. If you need to adjust the flame brightness, every time you press the
FLAME button, the brightness of the LED lamp front and back will become dark, the
display window of digital tube will be on brightness display. The digital tube in the middle
will flash display brightness level (5-4-3-2-1), every time you press the FLAME button,
the number will minus 1.If you press the DIMMER button when the flame brightness is
at the darkest level, it will returned to the brightest flame again.
CHANGE FLAME COLOR FUNCTION:
The default boot flame color is orange and press the COLOR MODE button on the
remote control, the display window by the temperature display to the COLOR display,
(C-1, C-2, C-3, C-4, C-5, C-6, C-7, C-8 , C-9).Every time you press the button, the LED
lights will light by (C-1)Orange- (C-2)green, (C-3)blue- (C-4)white- (C-5)green+orange-
(C-6)orange+blue- (C-7)orange+white- (C-8)green+blue- (C-9)green+white.
Child lock function:
The electric fireplace have lock function on remote control and keypad.After finished all
function setting of the products, press the "UP" and "DOWN" button together by 3
seconds on keypad or child lock button on remote control by one second, you will hear the
buzzer short sound, then the electric fireplace is locked, the button can not be operating.
The display window of middle display is in a flickering state by L after 10S the display
window will be turned back to the room temperature display. If you want to operate the
keyboard and the remote control again, you need to press the "UP" and "DOWN" button
together on keypad by 3 seconds or child lock button on remote control by one second,
and you will hear the buzzer short sound, the child lock function is unlock.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

NEVER dispose of batteries in fire. Failure to observe this precaution may
result in an explosion. Dispose of batteries at your local hazardous material
processing center.
Remote control battery used depends on the remote control type
which selected above.
NOTICE
This heater is equipped with a Temperature Limiting Control. Should the heater reach
an unsafe temperature, the heater will automatically turn OFF. To reset:
Turn the ON/OFF switch on the CONTROL PANEL to OFF. Wait 5 minutes.
Unplug the power cord from the outlet.
Inspect the fireplace to make sure no vents are blocked, or clogged with dust or
lint. If they are, use a vacuum to clean the vent areas.
With the POWER switch in the OFF position, plug the power cord back into the outlet.
If the problem continues, have your outlet and wiring inspected by a professional.
Temperature Limiting Control
Small remote control uses one CR2025 battery(included)
Remote Control Battery Information
1.
2.
3.
4.
5.
When the heater first turned on, a slight odor may be odor may be
present. This is normal and should not occur again unless the
heater is not used for a long period of time.
NOTICE
To improve operation, aim the remote control at the front of the
fireplace. DO NOT press the buttons too quickly. Give the unit time
to respond to each command.
NOTICE
14. Screen protection function:
The heaters have a screen protect function, If the heater working without operating on
the keypad or remote control for 30 seconds, the heater will automatically turn off all
the displayed light expect the power light.If you need wake up the display screen
again, you only need to press any button on the keypad or on the remote control then
it can be light up again.
-12-

Buff using a soft cloth, slightly dampened with a citrus oil-based product.
DO NOT use brass polish or household cleaners as these products will damage
the metal trim.
ALWAYS turn the heater OFF and unplug the power cord from the outlet
before cleaning, performing maintenance, or moving this fireplace. Failure to
do so could result in electric shock, fire, or personal injury.
CARE AND MAINTENANCE
Cleaning
Metal
Use a good quality glass cleaner and dry thoroughly with a paper towel or lint-free cloth.
NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
Glass:
Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
Clean the exterior of the fireplace with a slightly damp cloth or duster.
Vents:
-13-
NEVER immerse in water or spray with water. Doing so could result in
electric shock, fire, or personal injury.
The fan motors are lubricated at the factory and will not require lubrication.
Electrical components are integrated in the fireplace and are not serviceable by the consumer.
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
Maintenance
Electrical and Moving Parts:
Store heater in a clean dry place when not in use.
Storage:
WARNING! No other servicing should be performed by the consumer.
Do not attempt to service the unit yourself.
ALWAYS turn the heater OFF and unplug the power cord from the outlet
before cleaning, performing maintenance, or moving this fireplace. Failure to
do so could result in electric shock, fire, or personal injury.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM

DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO
ANY SERVICE.
ONLY A QUALIFIED SEVICE PERSON SHOULD SERVICE AND PEPAIR THIS
ELECTRIC APPLAINCE.
1.Wiring is loose
2.Ember is off mode
1.Low batteries.
2.Not aiming control correctly.
3.Defective remote control and /
or sensor
1.Fireplace turns
offand will not
turn on.
2.Flame is not
moving.
3.Flame is not
visible.
4.Log set and /
or is not glowing.
5. Remote control
does not work.
Problem Possible Cause Solution
Troubleshooting
-14-
WARNING
1. Pull the plug, wait 5 minutes to plug it
back in and turn it on.
1.Inspect wiring for loose connections.
2.Call a qualified service technician to
replace flame motor.
3.“Flame Rod”out of place due to rough
transit/handing of the product. This issue can
be corrected as simple as removing the
glass, flipping the fireplace upside and down,
removing a set of screws that are holding the
bottom frame plate and placing the flame rod
back into place.
1.Disconnect from power source and inspect
wiring for loose connections and repair or
replace if necessary.
2.Push the flame button to high.
1.Disconnect from power source and inspect
wiring for loose connections and repair or
replace if necessary.
1.Replace batteries in remote control.
2.Aim control at sensor located directly behind
glass screen in center of unit just above logs.
3.Replace remote control and/or sensor.
1.Fireplace has overheated and
safety devise has caused
thermal switch to disconnect or
home circuit breaker has opened.
1.Loose wiring.
2.Flame motor defective.
3.Flame rod out of place.
1.Wiring is loose.
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM
ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM ELM